GCV160 Honda Carburetor Clean and Tune-up Husqvarna HU700H

  Рет қаралды 75,287

The Lawnmower Lady

The Lawnmower Lady

Күн бұрын

How to resurrect a Husqvarna HU700H lawn mower with a Honda GCV160 engine that's been sitting for five years in a shed. Full carburettor clean and tune-up: air filter, oil change, and spark plug replacement. Same techniques for many mowers with Honda engines by Craftsman, Troy-Bilt, Toro, Lawnboy, and others.
Honda Air Filter: amzn.to/3pNJZRv
Honda float bowl gasket: amzn.to/2XVpYNi
NGK BPR5ES Sparkplug: amzn.to/3Eqrs1F
Honda 30W engine oil: amzn.to/3ClrkQr
Wireless Tachometer: amzn.to/3sHibiH
M6 stainless steel all-thread: amzn.to/37Fo3Bn
00:00 I am not Tardif L
01:33 Remove air box and fuel lines
03:58 Drain fuel and clear tank
05:29 Remove and clean tank fuel filter
07:25 Remove carburettor and clean exterior
09:25 Disassemble carburetor
14:08 Clean and polish carb bowl
16:07 Ultra-sonic cleaner process
19:01 Carburettor re-assembly
22:19 Replace carb, fuel lines, and air box
25:20 Replace air filter
26:18 Replace and gap new spark plug
28:55 Oil check and change
32:08 The money shot
32:50 RPM adjustment and test drive
The tools I like and use most often:
Magnetic spark plug socket set: amzn.to/3CzmpvO
Tachometer: amzn.to/3sHibiH
Vessel Megadora JIS screwdriver set: amzn.to/363RFqO
Channellock Bent Needle-nose pliers: amzn.to/3I5DbnA
Long 1/4 Quick-connect Torx Driver Bits: amzn.to/3HUNgnm
Spark Tester: amzn.to/3CxW2qi
OTC Leak-down Test Kit: amzn.to/3CyUhJn
Compression Tester: amzn.to/3IWd6sp
Wear your safety glasses, or you'll put your eye out. Try on some gloves. Take off that spark plug boot. Clean your room. Open the windows, those fumes are nasty. Just 'cause I do it, don't think it's the end all, be all solution. There's plenty more ideas out there, I can't take responsibility if you slice off a few fingers after watching my videos. And don't just pour that toxic stuff down the sewer or in the ditch, dispose of waste responsibly. Just be safe, OK?
Follow along with me elsewhere:
/ thelawnmowerlady
the-lawnmower-lady.blogspot.com/
Titles, opening graphics, and music by AbleVFX.
Any links to products are likely affiliate links, and I may earn a small commission from qualifying purchases (Thank You!), with no additional costs to you.
Disclaimer: The content of this video is purely for my entertainment, and is available to you for informational and educational purposes only. It's not substitute advice from small engine mechanics with professional training and certifications, nor does it create any kind of relationship between the The Lawnmower Lady and you. Your situation may be different, and the The Lawnmower Lady makes no warranties, express or implied, as to the fit, accuracy, or applicability of the information shown in this video, and implies no guarantee of results. The Lawnmower Lady and any sponsors of this video are not liable for any damages of personal injury, property damage or loss of any kind that may result from the use or reliance on this video and/or any parts and procedures represented in this video. You are using the information presented in this video solely at your own risk.
#gcv160 #honda #husqvarna #hu700h #lawnmower #smallenginerepair #DIY

Пікірлер: 374
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
If this video helped you, please consider clicking on the THANK$ button above 🙌 After all this and your mower still won't start? It might just be a bad brake cable: kzfaq.info/get/bejne/bp5kptSqrqu0Z5c.html
@xS0UL3ATERx
@xS0UL3ATERx 2 жыл бұрын
thanks so much for the walkthrough! i'm about to fix up an old one of these i have. Might video and add it to my channel or my company channel Son of a Fink. I'll Shout You Out For The Awesome Step By Step Tutorial. My Mower I let someone borrow and they left the gas cap off of it and it got rain in it. going to buy some replacement parts for it. new carb, filters, etc. and a new bail bar for the top because that's missing. LOL! Thanks again!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
@@xS0UL3ATERx I wish you good luck with that repair. I've started to tell people never loan out equipment, especially to family 😂
@xS0UL3ATERx
@xS0UL3ATERx 2 жыл бұрын
@@TheLawnmowerLady hahah yep great advice. my sisters ex-boyfriend is the one who messed it up! live and learn! 🤣😂
@thorbbs1854
@thorbbs1854 2 жыл бұрын
I have to say that I followed your KZfaq video on the Husqvarna self-propelled lawn Mower to the tee. You are an excellent small engine repair person. I did everything you recommended and followed your video. I could not start my lawnmower for various reasons. I must’ve pulled that cord over 100 times. I even tried carburetor cleaner spraying from the outside and it would only start for two or three seconds. After I completed your overhaul, the engine started on the first pull. I have to give you five stars on this video.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Happy to help Mr Thor! Cheers!
@williamhogg7830
@williamhogg7830 Жыл бұрын
LADY, you 're the BEST! How you get into every detail, will, this is what makes a good teacher from a GREAT TEACHER! I give you 4 STARS! THANK YOU SO MUCH.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Wow, thank you! I appreciate you watching. Cheers!
@residentmanager3088
@residentmanager3088 2 жыл бұрын
This is BY FAR the best tutorial for these Honda GCV160 engines. Mine is on a Ryobi pressure cleaner. Mahalo for your video!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Wow, thanks! I appreciate you watching. Cheers!
@TomDobyMowerRepair
@TomDobyMowerRepair 2 жыл бұрын
bless ya, i worked on 3 of those today, even after my shower i smell like i been refinishing floors haha
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
You and me both Mr Tom! I remember going to a brewery one time after a long day, and thy guy sitting next to me at the bar asked if I worked at a golf course. LOL. My overalls reeked of gasoline and freshly mown grass.
@marksavage4018
@marksavage4018 10 ай бұрын
A very thorough mower maintenance tutorial, with the close-up perspective that helps enormously! You had a LOT of helpful tips, but the one about guide bolts is the bees knees for keeping the cursing to a minimum. You are much appreciated! Thank you very much for your help, and encouragement.
@TheLawnmowerLady
@TheLawnmowerLady 10 ай бұрын
Glad you enjoyed it!
@clintdenman3037
@clintdenman3037 3 ай бұрын
I am a car mechanic and I am learning some great tricks from you i mean guides and things like that are handy for Honda cars you should patent some of your idea I mean seriously they work.
@TheLawnmowerLady
@TheLawnmowerLady 3 ай бұрын
Glad to help. I wish I could take credit for that stud idea. Honda actually makes this “tool” waaaaay overpriced. I’m too cheap for that, and made sadly own. I appreciate you watching. Cheers!
@brantsmallenginerepairs
@brantsmallenginerepairs 2 жыл бұрын
Great job breathing new life into that mower. Can't beat a "Hooskavarna" with a Honda engine. Like the M6 studs to hold everything together. Definately makes life easier. Keep up the good work!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for watching Mr Gerry!
@HobbyMotorDK
@HobbyMotorDK 2 жыл бұрын
As always easy to follow and fantastic camera work and Husqvarna spoken like a true Swede.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
I said that just for you Mr Claus! Cheers!
@TheShwa
@TheShwa 2 ай бұрын
You know your stuff well, and you explain things in a way that's both interesting and informative. Well filmed as well. One of the best how-to videos I've seen on You-Tube by far. Well done!
@TheLawnmowerLady
@TheLawnmowerLady 2 ай бұрын
Much appreciated!
@stephenhowlett5824
@stephenhowlett5824 2 жыл бұрын
Stella starting anything with one pull will keep me watching.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks Mr Stephen! I appreciate you watching. Cheers!
@ulrblitzer
@ulrblitzer 2 жыл бұрын
Just cleaned up a GCV160 and fought all the gaskets reinstalling the carb and air box. Love the idea of threaded M6 rods! Adding that to my arsenal.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Glad it helped. Cheers!
@EyobAklilu
@EyobAklilu 2 жыл бұрын
Thank you for this post. It helped me a lot. People like you makes this world a better place to live.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Wow, thank you. I truly happy I could help. Cheers!
@jerrystark6766
@jerrystark6766 13 күн бұрын
Using the M6 x 1.00 threaded rods to maintain alignment of the parts and gaskets is genius! Well done. Possibly, I have a tip that you might find useful. Before you unscrew the main jet, insert a piece of wire (I use a straightened paper clip) into the hole in the side of the main jet housing. (I have also used a plastic toothpick to do this also works well.) Keeping slight pressure on the jet with this wire and prying upwards as the jet loosens from its threads as you unscrew the jet will make it much easier to remove the jet. No tapping or pounding will be necessary. Thanks for the video. 👍👍
@TheLawnmowerLady
@TheLawnmowerLady 2 күн бұрын
Great idea, I actually do that with a small dental pick sometimes. Thanks for watching. Cheers!
@beakittelscherz5419
@beakittelscherz5419 Жыл бұрын
Water in the Fuel, dirty Carb, Airfilter Oily... This Mower had no Chance to run... Nice Vid! Lots of good info to use on ya own machine. Awesome Content on this Channel!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thank you so much for watching. Prost!
@brianmcglew2117
@brianmcglew2117 2 жыл бұрын
Great video! The M6 tip was awesome. Thank you for taking the time to make these videos and please keep them coming!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks Mr Brian, will do! I appreciate you watching my videos. Cheers! 😀
@xylemmelyx
@xylemmelyx Жыл бұрын
Dear, dear Lawnmower Lady, thank you, thank you, thank you! You saved my bacon. Guitar strings is genius. You gave me the courage to completely disassemble my carb and I finally found the chunk of crud inside the brass emulsion tube. After 4 days of messing around, it's now runnin' like a champ, thanks to you!!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
You are so welcome! I appreciate you watching. Cheers!
@gregoneill1495
@gregoneill1495 2 жыл бұрын
It was cheaper for me to replace my carburetor as bad as it was. Thanks for the great video.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for watching Mr Greg. I know the OEM Honda carbs are very reasonably priced in USA. Crazy expensive in UK. Cheers!
@biggaspirit1
@biggaspirit1 2 жыл бұрын
Systematically worked through, checked, and tested. All good. Thank you again Mrs Lawnmower Lady.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
You're welcome Mr Bigg! I appreciate you watching :)
@nashguy207
@nashguy207 2 жыл бұрын
What a fantastic job bringing this mower back to life. Great video for people that need help with these problems to watch. I'M loving my Vessel JIS screw divers. Have a great week!!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for watching Mr Bob! Glad those tools are working out for you. Cheers!
@sumfunnow7800
@sumfunnow7800 Жыл бұрын
I love the "emptying the gas tank trick", using shop air!!! Especially if there is some water in the tank! Great channel! Thanks!!!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I do appreciate you watching. Cheers!
@MayweatherjrWONandsoTrump
@MayweatherjrWONandsoTrump Жыл бұрын
Very professional and detailed yet, easy to follow. Thank you for giving us your time and support.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
You're very welcome! I appreciate you watching. Cheers!
@PoplarForest
@PoplarForest 3 күн бұрын
Your video helped me clean my carb on a pressure washer with the same motor. I went out and bought carb cleaner, welder tip cleaners, and some threaded rod, I figured I should pay a little bit for the tool of knowledge as well.
@TheLawnmowerLady
@TheLawnmowerLady 2 күн бұрын
And a Super Thanks! to you for supporting my channel. Cheers!
@almclean4835
@almclean4835 2 жыл бұрын
Good job Stella. I like the idea of using the threaded bar to keep everything in place👏
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thank you Mr AL ! 😊Cheers!
@tomnelson3383
@tomnelson3383 2 жыл бұрын
Genius, using the 10mm studs to keep everything aligned. Absolutely helpful. Thank you so much.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
I hope it helps you Mr Tom. Thanks for watching. Cheers!
@johnrhodes7487
@johnrhodes7487 2 жыл бұрын
Great video Stella I love the idea of the 2 threaded rods in the carburettor. And will be making some as soon as I can. Cheers Stella. Mr John 🇬🇧
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for watching Mr John! Honda actually makes this tool, it's overpriced in my book when it's wasy to fabricate something this simple. Cheers!
@lyndawkswks853
@lyndawkswks853 Жыл бұрын
You are a legend a carburettor no longer a mysterious cylinder thing! Thank you
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I appreciate you watching. Cheers!
@scuba6797
@scuba6797 2 жыл бұрын
Thanks for showing every step of the way. You are amazing!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for watching. Cheers!
@donaldsoncharles637
@donaldsoncharles637 6 ай бұрын
Excellent video. The guide bolts tip makes life really easy.
@TheLawnmowerLady
@TheLawnmowerLady 6 ай бұрын
Yes it does! I appreciate you watching. Cheers!
@juancam648
@juancam648 2 жыл бұрын
I'm an auto by trade, and I hate working on these small engines, but I did learn a few things for your video like the filter tube in the fuel tank and the line. Thanks for posting this!!!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks Mr Juan! I appreciate you watching. Cheers!
@tinkeringtaylor3053
@tinkeringtaylor3053 2 жыл бұрын
Great video Stella good clean up on the carb well done 👏👏
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thank you Mr Nev 😁 Cheers!
@CarlosGonzalez-mr5qz
@CarlosGonzalez-mr5qz Жыл бұрын
Hi Lawnmower Lady! Your videos have helped me out a lot! The metal studs is a great idea. My Craftsman GCV190 had a surging problem. Idle circuit jet was clogged. Thank you for making these videos!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Happy to help. I do appreciate you watching. Cheers!
@johnwallis1309
@johnwallis1309 Жыл бұрын
Thank you ,so valuble to me,two outboard motors and a lawn mower ,and cement mixer engine now fixed ,one carb seem now very much like most others, saving much money thanks
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad to help. Thanks for watching!
@claymandeviant
@claymandeviant 2 жыл бұрын
Many thanks for this video. You helped me ressurect my crippled Honda motor. Thanks once again!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Glad I could help. I appreciate you watching. Cheers!
@dr.lmsb4456
@dr.lmsb4456 2 жыл бұрын
Awesome how to video Stella!. Thanks for sharing . Ive seen these machines a few times in my shop . Lol hope all is well take care and stay safe out their ...
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for watching Doc! Cheers!
@neeneko
@neeneko Жыл бұрын
Great video! This told me exactly what to expect taking things apart and putting them back together.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thanks for watching. Cheers!
@AaronW315
@AaronW315 2 ай бұрын
Perfect and clear information, thank you for being so thorough!
@TheLawnmowerLady
@TheLawnmowerLady 2 ай бұрын
Glad it was helpful!
@TLMD
@TLMD 2 жыл бұрын
Very nicely done Stella! I always enjoy your videos. I love how you always make it a point to tech people the right way to do things. Keep it up!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks so much Sgt! I appreciate you supporting my channel. Cheers!
@dennyheitzer9457
@dennyheitzer9457 Жыл бұрын
Really appreciated your reply to Pete Malone on the RPM adjustment. I've been trying to figure out where and how to tweak the RPM and the correct operating RPM to set to. Your video was a real benefit to me because of the excellent video. My air butterfly valve jumped its mechanical stop and I needed to see the correct travel of the valve. I also liked your breaking the video into segments and the threaded rods for reassembly. It was suburb, well thought out, and full of really good helps and tips. I immediately stopped and made the rods before going on to ease the valve back to proper operation. Thanks much. I'll be looking up your other videos. I am a retired Field Service Engineer working on every kind of hospital Radiology equipment. I know how to fix things I'm not familiar with and finding your video was a treasure. I don't usually comment, but I had to make this comment to you. Thanks again.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Wow! Thank you Mr Denny for your kind words. I'm so happy to be able to help. I really appreciate you watching. Cheers!
@classiccycleconnection9334
@classiccycleconnection9334 Жыл бұрын
Very good video. I successfully cleaned carb and lines. On the studs to reassemble, I didn’t have the correct length bolts to make the guides so I trimmed down some wooden chop sticks from a take away place. Worked fine. I also siliconed as many gaskets in place as possible not covering any holes. One thing on reassembly is this video didn’t mention which way the emulsion tube went. I checked another video of yours to get the answer. The tip on the fuel screen was terrific. Thanks for the help.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Nice call on the chopsticks. My ex-boyfriend always had some buried under his scooter seat, handy to have around. Thanks for watching. Cheers!
@classiccycleconnection9334
@classiccycleconnection9334 Жыл бұрын
@@TheLawnmowerLady Now mind you I did finally buy some 6mm x1.0 studs and slotted for the next time .
@SheikShak
@SheikShak Жыл бұрын
The best of explanation……very good video….thank you sooooo much!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
You are welcome! Thanks for watching.
@JoseHernandez-rl8fx
@JoseHernandez-rl8fx 2 жыл бұрын
I would like to say that your video is by far one of the best husk of honor all will drive best detailed videos I loved the way you took your time and care and very very carefully worked and videotaped every step-by-step by step with the utmost respect to the workmanship as a workmanship as a mechanic you are top notch I don't even know how to put it into words but you make someone like myself who knows nothing about lawn mowers feel like a pro thank you For your video thank you for your time and thank you for all your knowledge
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thank you Mr Jose! I appreciate your kind words. Cheers!
@robbywells3201
@robbywells3201 Жыл бұрын
Thank you for your video, it helped me fix my mower. I didn’t know what and what not to remove on the carburetor. Very informative. 🎉
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Happy to help! Thanks for watching. Cheers!
@tonybeeguy
@tonybeeguy Жыл бұрын
I loved your video. I wished I had seen it Before starting to work on my mower. I kept thinking,"I wished they had used studs instead of bolts to hold everything on. I have my carb in place with bolts just started, but still need to hook up governor, bresther tube, etc. I will get threaded rod, so I can slide the assembly out to do all that. You videos are wonderful. I love that you take your time, explain everything well and don't speed through, or skip anything. You're the best. Thank you so much.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thanks so much for your kind words! I appreciate you watching. Cheers!
@tundra-7549
@tundra-7549 2 жыл бұрын
That was impressive. Great job. Love the old school just get your hands in the gas while cleaning with the brush 👍👍
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
To be honest, I really should don those gloves more often. 😬 Thanks for watching. Cheers!
@philliphall5198
@philliphall5198 Жыл бұрын
59 years of mechanic work and only ware gloves while working on hydraulic systems Hate it on my hands
@jamestyrer6067
@jamestyrer6067 Жыл бұрын
GREAT VIDEO. REALLY LIKE THE 6MM RODS TO HOLD EVERYTHING TOGETHER. COOL IDEA 👍
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad you liked it!
@Turningwrenches85
@Turningwrenches85 2 жыл бұрын
Great work Stella 5 years and sounds like it was running just yesterday not missing a beat that Honda engine no skips either lol . I like your idea of the studs to hold the Honda carb it was always tricky to hold everything all at once. Look forward to the next one 🍻
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
I really appreciate the comments! Thanks for watching. Cheers!
@philliphall5198
@philliphall5198 Жыл бұрын
I’ve been surprised how many old push mower have been brought in to be repaired this year that’s been setting up for years
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Some folks bring me 2 or 3 mowers that they have had "for years" rather than taking them to the dump. Even if they are too beat up to fix, they make great parts machines
@mharing
@mharing 2 жыл бұрын
Nice tip with the threaded studs!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for watching Mr Michael. Cheers!
@TheRustyRooster
@TheRustyRooster 2 жыл бұрын
Great tips Stella truly enjoy your content simply can't get enough so ill just watch again 🐓👍
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
☺😘
@timpearce4255
@timpearce4255 Жыл бұрын
Thanks for the handy tip about making two 6mm x 4.0" slotted studs. made a set makes carb r&r easy... That is why I liked and subscribed... You go girl!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thanks Mr Tim. I wish it was my idea, but Honda actually sells this "too" for way too much $$. I figured I could make do with something home grown. I appreciate you watching. Cheers!
@wlhcrh02
@wlhcrh02 Жыл бұрын
Thank you, doing this tomorrow in Pasadena, Ca
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Hope this works out for you. Thanks for watching!
@vicX276
@vicX276 Жыл бұрын
Nothin like a lawn mower lady. Thank you ❤️
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thanks for watching. Cheers!
@DavidMartin-ev2kt
@DavidMartin-ev2kt 9 ай бұрын
I have this exact carb and air box with the auto choke system on a LC221RH Husqy that was given to me by a friend who couldn't get it running about 2 years ago and I can't get it to start with anything other than a shot of carb cleaner directly into the air box. Kicks on and sounds perfect but immediately shuts off. I have taken apart the carb and cleaned it with my very limited knowledge and put it all back together only to be met with the exact same result. Now that I've watched your incredibly thorough walk-through of this engine, I will be trying again but this time removing the jets that I was afraid to touch, and making sure all the passageways are clear! Thank you so much for the extraordinarily helpful video. I also told my wife I need an ultrasonic cleaner, so I'll try that as well. Thanks again! David.
@TheLawnmowerLady
@TheLawnmowerLady 9 ай бұрын
Thanks for watching. Pay special attention to the idle circuit, located under a screw on the top of the carb. There are two versions, both in which you must remove the idle speed screw to remove the jet screw. The one with the metal idle speed screw has a metal JIS (similar to a Phillips screw) and the brass jet underneath is not removable. The other with a plastic idle speed screw has a removable idle jet. It too is plastic and is removed by gently prying up. Make sure the o-ring is in good shape and the passages are clear. Avoid carb spray on the rubber bits. Brake parts cleaner is less aggressive. Hope this helps. An ultrasonic cleaner is less expensive than a new mower, considering there are so few mowers of a decent quality these days. Besides, she can clean all kinds of things like jewelry :) Cheers!
@jonlambshead5115
@jonlambshead5115 Жыл бұрын
Another Well Explained, Well Presented Video. It Is A Pleasure To Watch Your Videos, Great Mechanic.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thank you very much! I appreciate you watching. Cheers!
@henrymurawskibigdogrepair
@henrymurawskibigdogrepair 2 жыл бұрын
Well done Stella I did the same thing with 2 new bolts to reassemble the carb two great minds think a like
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks Mr Hank! 👍
@Inisfad
@Inisfad 2 жыл бұрын
Those 4 inch threaded studs are the trick! I did this without them, and lining up the heat shield, carb and air cleaner, without the ability to actually see anything, was a nightmare.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Especially the older ones, several more gaskets. A fiddly mess!
@dereksmith4178
@dereksmith4178 2 жыл бұрын
Great video I love the using the threaded studs too hold the gaskets in place it’s alway been a pain with Hondas
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for watching Mr Derek! I wish I could take credit for the original idea. Honda actually makes this "tool" It's very pricey, so I fabricated my own. Cheers!
@MikeSki1984
@MikeSki1984 2 жыл бұрын
Thank you SO MUCH for this vid, esp the studs. Wish Ida seen this vid 2 days ago bc trying to put everything back together after everything falls off is a royal PITA!! Thank you...going to buy some and slot them myself, now. 🙏
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks Mr Mike! I wish I could take credit for the idea. Honda actually makes this same "tool", crazy expensive too. I appreciate you watching. Cheers!
@ajones5578
@ajones5578 10 ай бұрын
Excellent video. Thanks for taking the time to explain. Following you now.
@TheLawnmowerLady
@TheLawnmowerLady 10 ай бұрын
Awesome, thank you!
@RonBurgundy209
@RonBurgundy209 Жыл бұрын
Just stumbled across your page today while looking for answers why the Husqvarna that was given to me kept stalling after a few minutes. I changed the oil, put fresh gas (tank was completely empty) and a new filter. I’m new to this, so this video is definitely gonna help. You just got a new subscriber. 👍🏻
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Welcome aboard! Glad to help. Cheers!
@kevinbaxter607
@kevinbaxter607 Жыл бұрын
I thought my carburetor was dirty, but wow, lol, that one was just awful! Excellent tutorial and a great help to those of us do-it-yourselfers, thanks very much!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I appreciate you watching. Cheers!
@philliphall5198
@philliphall5198 Жыл бұрын
I love the factory manual cut off valve they have on them Very very smart ideal
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Honda is (was) high quality, but rarely does the average Joe even know what it's used for.
@MachineryNation
@MachineryNation 2 жыл бұрын
Nice one Stella. I can’t believe how you say Husqvarna, Claus @hobbymotor will be a happy man! 😂
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks Mr James! I learnt from the master 😆
@baldeagle242
@baldeagle242 2 жыл бұрын
Another great video young lady. Gotta love the apple cider jello. 😉
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
It's the best Mr Steve! LOL. Thanks for watching!
@Rattletrap2
@Rattletrap2 2 жыл бұрын
Excellent video and nice work!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thank you! Cheers!
@petemalone7897
@petemalone7897 2 жыл бұрын
Great all-around step by step, and you present it all so clearly! I wish you’d been more specific about how you set rpm. Low revs and loping on a 160 is what brought me to view this video, so if you can reply to the question, it’s a big help. I’ll go back and see if I can get the gist of what you were doing to check and adjust rpm. Many Thanks!!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for watching Mr Pete! generally speaking, the other end of governor return spring is attached to a fixed (but bendable) point. If you increase tension on the spring, the RPM increases. I hope this helps.
@petemalone7897
@petemalone7897 2 жыл бұрын
@@TheLawnmowerLady perfect!! Can do! XO ~ Pete
@PanefullyClear
@PanefullyClear Жыл бұрын
My Hoosk AWD quit pulling itself. I tried to just push it and it started making a loud noise. Stopped it right there and looking for ways to repair. That is how I wound up coming here. This video is excellent. Makes me almost want to clean the carburetor during my downtime (not)... Thank you for sharing your knowledge. Am subscribing and looking for your advice on my drive problem, before I possibly wind up taking it to a shop.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Oh no! Definitely check under the deck to make sure that belt is not jammed up. Could be a seized drive pulley, or some obstruction, twig, branch, pinecone, etc., stopping the belt. You should be able to pull on the belt easily, and see the wheels turning. Lift the drive wheels off the ground, pull the spark plug and see if everything turns easily. Hope this helps. I appreciate you watching.
@MrCobra762
@MrCobra762 Жыл бұрын
Very thorough and extremely well done, thank you! The 3rd video I watched on this engine and carb, and the last I need to see! Log splitter will run again today. Subscribed.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I appreciate your kind words! Thanks for watching. Cheers!
@MrCobra762
@MrCobra762 Жыл бұрын
@@TheLawnmowerLady After doing this, I do have one question though. When I clean carbs I usually use my torch cleaning kit, but on the jet under the screw, even my smallest in the kit will not go through? Is the guitar string you used smaller than that, or could it just be that clogged? Didn't have any solvent or pinesol so I didn't soak the carb, but everything else was really clean and didn't need it. Just had a little water in the bowl from sitting up a season. I'm a guitar player so I do have some extra stings somewhere...
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
@@MrCobra762 that was an E string as I recall. It only goes about 1/2 inch (13mm) on the top. You should be able to see the string when inserted in the small hole in the throat of the carb. Hope that helps.
@MrCobra762
@MrCobra762 Жыл бұрын
@@TheLawnmowerLady Yes indeed. Thank you!
@thebeardedstork432
@thebeardedstork432 2 жыл бұрын
That was a nasty one! I think your practice of putting a little WD40 on your gaskets, etc. is a good one. We always used a little film of oil on those paper or fibre type gaskets in refrigeration work to help them seal better. I will definitely work on making up those 4" long M6 rods for future use as well. Good idea! I also bought some magnetic spark plug sockets after seeing one of your videos as well. Your videos are always very clear and concise. The information is delivered in a very professional manner! Lots of helpful tips!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for that info. You confirm my theory that seals better. I appreciate you watching Mr Brian! Cheers!
@mjoe877
@mjoe877 3 ай бұрын
Great video. Thanks for sharing!
@TheLawnmowerLady
@TheLawnmowerLady 3 ай бұрын
You bet!
@aras_mileska
@aras_mileska 2 жыл бұрын
Great video! Same design as my lawnmower (McCulloch M56-190AWFPX). Thanks!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
I appreciate you watching. Cheers!
@alia176
@alia176 Жыл бұрын
What an awesome video, thank you very much.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad you liked it!
@mr123ert678
@mr123ert678 6 күн бұрын
You did an outstanding really good job - so helpful - Thank you
@TheLawnmowerLady
@TheLawnmowerLady 2 күн бұрын
I appreciate you watching. Cheers!
@andersforrad
@andersforrad 2 жыл бұрын
Lol Stella - I just love the way you say Husqvarna - spot on there 😂 I just made a video today with your sticker in it. Cheers!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Cheers Mr Anders! I learnt to say it right from all you guys across the pond 😀
@kplathan7545
@kplathan7545 Жыл бұрын
You helped a lot. Thanks!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
You're welcome!
@Restorology
@Restorology Жыл бұрын
Thank you for sharing this.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I appreciate you watching. Cheers!
@raulaybar323
@raulaybar323 Жыл бұрын
Thanks my dear lown mower,,,,thumbs up 👆
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thanks for watching. Cheers!
@petefroud5308
@petefroud5308 2 жыл бұрын
Great job Miss Steller.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for watching Mr Pete! Cheers!
@francislang5075
@francislang5075 2 жыл бұрын
great camara work
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
I appreciate you watching. Cheers!
@waynethurman2144
@waynethurman2144 Жыл бұрын
Excellent video woman!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thank you! I appreciate you watching.
@rickleger3528
@rickleger3528 2 жыл бұрын
Great video I have that mower and lov it now I know how to take care of, thanks again
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Right on Mr Rick! Thanks for watching. Cheers!
@rickleger3528
@rickleger3528 2 жыл бұрын
I’m now a subscriber I hope that helps
@jphthree3
@jphthree3 Жыл бұрын
You are the bomb❣️
@edwardburke9181
@edwardburke9181 2 жыл бұрын
Glad it went a spider stella lol great video like the carberator rod tip too
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Me too Mr Edward! Not much freaks me out, but spicers do every time! Cheers!
@willschmahl1240
@willschmahl1240 Жыл бұрын
Excellent video..
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thank you! Cheers!
@snoopysrc
@snoopysrc 2 жыл бұрын
Lawnmower Lady you gotta new sub
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Awesome! Thank you!
@BrucesShop
@BrucesShop 2 жыл бұрын
Watching and commenting as i go. Huskavarnaaa. Love it. I gaurentee I would replace the torch plug. LOL For me those Honda carbs and gaskets are, new (my age). Too funny. I use air to mildly pressure tanks to drain. TIP Add a bit of alcohol to the tank to reduce time to dry. Pino Grigio bottles. We have a few of them around here. You are a prof? You could be !!! Pine sol in my Ultra sonic is a great idea. You use the separated system. I dunk my carbs into a full tank of whatever I think s the best. Guitar string brilliant. JIS screwdriver. I as well as you gap every plug as they can be dropped. I knew it would run!! Brilliant video.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks Mr Bruce for watching. I appreciate your keen eye. I'll have to try the alcohol thing for those cloudy days. Cheers!
@dj5752
@dj5752 2 жыл бұрын
Well done. Thank you
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for watching!
@grgygantz6760
@grgygantz6760 2 жыл бұрын
In watching your video I have the same exact Husqvarna mower. With the same exact Honda engine and I had the same exact carburetor problem. I got it all apart got it all cleaned even let it soak overnight and sea foam. Then cleaned it with gum out and compressed air put it all back together would not run. At that time I opted just to buy a brand new carburetor I put the carburetor on in the morning refill the tank of fresh gas first crank it started right up.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Glad that worked for you. Cheers!
@notme22
@notme22 2 жыл бұрын
Nice job and good video! One tip though use either a JIS or electricians screwdriver.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
I did! LOL
@INSIDEHOUSEGARAGE
@INSIDEHOUSEGARAGE 2 жыл бұрын
excellent Job!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thank you Mr IHG! Cheers!
@peteg6613
@peteg6613 Жыл бұрын
First of all great job on video and service your providing, I have the exact same mower, and wont start, i bought it new and my daughter used it for about 2 yrs then passed it back to me, i used it for about 2 yrs, then it just wouldn't start, so just before the 4 yr warranty ran out, i took it back to lowes, and they sent it off to some rep shop, they replaced the carb, and changed spark plug and oil, they claim that was poor maintenance, so i had to pay the 125 charge, it ran a few months the winter came and summer came and it worked a few more months, then it just quite starting again,so i removed the carb and it had some water in it, (maybe my fault for not storing it in the garage but i did have a large bucket over the engine), i drained the gas tank and used carb cleaner on the carb and reinstalled it, then it would start but sputter and rpm would raise up then lower, i ran it for an hour or two, just to see if it would clear itself, but then it turned off and would not start, i was disappointed on the 500 dollar Honda engine mower, so i parked it for a year, (compared to my 129 dollar disposable murray mower that was on its 7th yr with no maintenance was still starting on first or second pull) Now Im working on it again, I bought a new carb for it, (to resolve and carb issues) installed it, tank was empty so i put new gas, still wont start, i pulled the spark plug and i get fire, if i sprayed some starter fluid (i heard you shouldn't on lawn mowers), it now starts up for a few 1 or 2 seconds then turns off, i did have to grease the brake cable for it to work, but it was stuck in the run position, and i am using the red can fuel, still wont start, i will clean out the gas tank tomorrow and verify the gas is getting all the way to the carb, im sure some is cause when i had the fuel line removed from the carb, i turned on the fuel line and gas came out of the end, but maybe not enough, I'll check that and the brake line and install another new spark plug tomorrow. any more suggestions?
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Still could be residual fuel/water in the very bottom of the tank or fuel lines? Replacement aftermarket carbs can be problematical. I'd go back to the other carb, give it a good clean, paying special attention to the idle jet (the small screw on the top) and replace the brake cable. If it was stuck, it was due to rust from water/rain seeping inside and down the outer cable jacket, I guarantee it will break in the future. I think storing it outside, and prior use of ethanol laced fuel is largely the cause of these problems. Hope you get it sorted. Thanks for watching.
@peteg6613
@peteg6613 Жыл бұрын
Update: I removed the fuel line from the carb and drained all the fuel from the tank and got about 12oz of fuel even though i thought it was empty from the beginning. There was less than a trace of water, i then removed the tank so i can check the filter and blow out the fuel line, for some reason there was still fuel in the tank, tipping it over and upside down and all around i got about another 4 ounces, 95% of that was water, surprised me, blew out the tank and fuel line and removed carb, removed fuel bowl and it was 100% water, Reinstalled the gas tank and left fuel bowl off and reconnected fuel line, can see fuel coming out of the bottom of the carb, replaced bowl and attempted to start the mower, it started on 2nd pull, that was about 7 hrs ago, for the next hour after that it sometimes had trouble starting, needed 4 or 5 hard pulls, I just went to turn it on, it started on the 1st pull, in conclusion i believe the main issue was water in the tank and carb, after COMPLETELY cleaning fuel system out it works, I will replace the brake cable soon, and i did install a new Honda carb, not an after market so it will be stored it in garage. Thank you very much for the video again,
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
@@peteg6613 Yay! Glad you got it sorted. If you suspect any more water, let the empty tank sit in the sun for a good afternoon, to ensure all the water has evaporated. Cheers!
@lamarprice5680
@lamarprice5680 2 жыл бұрын
Enjoy your video’s
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thank you for watching Mr Lamar! Cheers!
@mgomez5606
@mgomez5606 Жыл бұрын
I did not know you could put parts in different container in the ultrasonic cleaner. Learn something every day.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Keeps me from having to empty out the entire reservoir. I use different cleaning solutions, and often use a coffee filter to strain out the solids, and reuse the same solution over and over.
@mgomez5606
@mgomez5606 Жыл бұрын
@@TheLawnmowerLady what solution do you use?
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Most of the time I use Pine-Sol and water, about 1:5 ratio, sometimes vinegar/water, sometimes petrol. Depends on how gummed up the parts are.
@mgomez5606
@mgomez5606 Жыл бұрын
@@TheLawnmowerLady my wife uses pinesol to clean so no shortage of that.
@tomnelson3383
@tomnelson3383 2 жыл бұрын
Thanks!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
You're welcome Mr Tom! I really appreciate you watching. Cheers!
@jamestyrer6067
@jamestyrer6067 Жыл бұрын
GREAT VIDEO. YOU CERTAINLY KNOW WHAT YOU ARE DOING. THANKS
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I appreciate that! Thanks for watching. Cheers!
@israelavila5403
@israelavila5403 Жыл бұрын
Muy bien explicado gracias 👍
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
De nada. ¡Salud!
@TheShaggyRifleman
@TheShaggyRifleman 2 жыл бұрын
Fantastic!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Many thanks for watching Mr Shaggy! Cheers!
@TheShaggyRifleman
@TheShaggyRifleman 2 жыл бұрын
@@TheLawnmowerLady Cheers to you as well! 🍻
@guesswho2378
@guesswho2378 2 жыл бұрын
You don't know it yet, but you and I are going to get married!!! Great job on this intricate little project of yours, but would it disappoint you if I told you that you convinced me that it would be a lot easier for me just to get a new lawn mower? But honey, I SWEAR to you----you've inspired me to take much, much better care of the new mower than I ever did with this old mower,, which really isn't that old at all. Sweet Jesus! I have found my muse in you! Merci! Merci!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Glad I can help. Cheers!
@dungho8762
@dungho8762 Жыл бұрын
Thanks
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Welcome. Glad to help.
Honda GCV Carburetor Service for Troy-bilt TB240 Lawnmower
22:24
The Lawnmower Lady
Рет қаралды 63 М.
Honda Mower GCV160 Keihin Carburetor Service
28:41
The Lawnmower Lady
Рет қаралды 130 М.
He sees meat everywhere 😄🥩
00:11
AngLova
Рет қаралды 11 МЛН
HOW DID HE WIN? 😱
00:33
Topper Guild
Рет қаралды 39 МЛН
That's how money comes into our family
00:14
Mamasoboliha
Рет қаралды 9 МЛН
How To Clean a Honda Style Carburetor (Step-by-Step)
20:01
Steve's Small Engine Saloon
Рет қаралды 1,5 МЛН
Honda HRC216 No Start: GSV160 Carburetor Clean How To
14:54
The Lawnmower Lady
Рет қаралды 164 М.
Husqvarna mower Wit Honda Engine That Needs Some Help.
29:51
Raymore Repair
Рет қаралды 449
Full Detailed Honda GCV160 GCV190 Carb Clean [4k]
22:48
Wild_Bill
Рет қаралды 61 М.
Is This Old Stihl MS170 Chainsaw Worth Fixing?
27:51
The Lawnmower Lady
Рет қаралды 105 М.
3 Must Have Upgrades for Your Husqvarna Lawn Tractor
17:37
Johnson's Small Engines
Рет қаралды 62 М.
Proper Way To Tip A Lawn Mower Over
8:50
Steve's Small Engine Saloon
Рет қаралды 4,2 МЛН
Popping green grap jelly!- got these in Japan
0:16
Priya kumari
Рет қаралды 28 МЛН
Черешня из Китая размером с КУЛАК: На стероидах?
0:12
Собиратель новостей
Рет қаралды 5 МЛН
Рука застряла в заборе
0:27
RICARDO
Рет қаралды 1,3 МЛН
Как красиво снять полет #marim #shortsvideo
0:15