🔴Thanks for watching and if you have liked the Video then you can check out my Master Class on 👉 UDEMY I am highly positive that you would find the Master Class super valuable. Link to Udemy Masterclass : www.udemy.com/course/how-to-read-pids-piping-instrumentation-diagrams-symbols/?couponCode=LOWESTPRICE389 My best wishes for your success, Keep learning and keep growing in your career !!! ✔
@Sreeram.G2 жыл бұрын
Asad it's a apt case. There is another dynamic also when thermo well is installed at an angle to the pipe and another when at a elbow in the pipe.
@AsadPassionateEngineer2 жыл бұрын
Thank you 😊. And yes you are very correct "elbow" and "angle" installation are also important cases . Where we need to see the direction of flow etc
@bhagwansinghlodha93911 ай бұрын
Sir plz share lone size thermowell calculation. And why use angle thermowell And how much will dip thermowell in the pipe
@Kanmanis_official2 жыл бұрын
Expecting more instrumentation knowledge from you
@AsadPassionateEngineer2 жыл бұрын
Sure, Thanks for your kind words of Motivation. It means a lot 😊
@pandey.vivekk2 жыл бұрын
I usually get highest line velocity by process not flow rate in temperature cases.
@AsadPassionateEngineer2 жыл бұрын
@Vivek Pandey correct same was the case with one project that I was working. Process had given highest velocity and then.... After the process data was received it was decided to add a blower to the line so that thermowell is inserted well in the process but still engineer's were taking the same velocity which was for a smaller line size. And for smaller line sizes the velocity is usually high so no wonder the thermowell was not passing the WFC test .....
@abdessamedghettas71672 жыл бұрын
Thanks
@AsadPassionateEngineer2 жыл бұрын
Glad you liked it! 😊
@ruchirdave8562 жыл бұрын
Very Very Good 👍 Nice 👌
@AsadPassionateEngineer2 жыл бұрын
Thank you so much 😊
@salmankhan-ju6qy Жыл бұрын
Hi Asad. Good video. Just wanted to know upto what size ,pipe swaze up is done
@AsadPassionateEngineer Жыл бұрын
Dear Salman, As a thumb rule For any size less than 4" we swage up the line to 4". I hope this is what you wanted to know !!
@Kanmanis_official2 жыл бұрын
To know the insertion length, immersion length stem length like this
@AsadPassionateEngineer2 жыл бұрын
Do you mean the steps as to how to calculate U-Length of Thermowell ? (Please let me know if i have erred in my understanding )
Sir good evening can you please make some videos on each different types of instrument data sheet with deep explanation which will help me get stronger knowledge
@AsadPassionateEngineer2 жыл бұрын
Sure !! I will sure make on these topics as well 😊
@MohammadAhmad-io8rn2 жыл бұрын
I was waiting for this type of videos
@pandey.vivekk2 жыл бұрын
In cas of Helical type TWs. Should we not ask for Vibration calculation anly we can ask for stress calculations.? Please guide
@AsadPassionateEngineer2 жыл бұрын
Yes even we had asked for stress calculation since even through the helical spikes are present they can avert only vortex shedding Damage but the thermowell must be evaluated for static stress. While we were working for a project of a top oil and Gas company we had confirmed from vendor that vortex shedding would not be an issue and just asked for stress calculations Hope this helps 😊
@Kanmanis_official2 жыл бұрын
Sir can you please make a video on thermowell calculation for of TE &TT
@AsadPassionateEngineer2 жыл бұрын
Yes sure.... You mean Wake frequency Calculation ?
@SahilShaikh-wm6fu2 жыл бұрын
Yes this is similar to bernouliis principle that I learner during jee 😅
@AsadPassionateEngineer2 жыл бұрын
So true !!
@robinsonalexander9767 Жыл бұрын
how to download PIP std ..pls provide the link
@saieashwar69972 жыл бұрын
Does Process ever give it in velocity? Don't they usually give in Flow rate?
@AsadPassionateEngineer2 жыл бұрын
@Sai Eashwar ! It is really good that you get the values in Flow rate. I have worked on quite a few projects where the process department would give us the fluid velocity !! Usually in m/s ( Meter per second)
@Kanmanis_official2 жыл бұрын
Then whats the standard can we use it? As you said PG explanation video
@AsadPassionateEngineer2 жыл бұрын
can you please elaborate your question ? thanks 😊
@Kanmanis_official2 жыл бұрын
@@AsadPassionateEngineer what are standards used for TG and TE