Is this wire compatible with any digital input? An open circuit during normal times, and a short circuit after a heat event?

I think you explained your analogy with the car backwards/improperly when repeated later in the video. How is it that the Cv (or speed) would be high in maximal traffic conditions? You showed it this way at least a couple of times. You should fix it.

Very interesting asad thank you

How to get job in design field at initial stage ? It is very hard to find a job because many of companies required 2-3 years of experience in design. Where and how to start ?

Kygdiyd

Yes we are waiting for part 2 video,please upload asap .

how to review a wake frequency calculation from vendor. what are the main points to be check

hi

how to review a wake frequency calculation from vendor. What are the points to be checked?

Sir, If beta ratio of orifice is 0.8 then we should reject it or anything else we need to check. Please confirm sir... Thank you.. If possible please make a video what to do if beta ratio is high then 0.8 or less than 0.3. Thank you in advance sir

Nice video..Instrument index also cover Instrument type,then subtype ,line no,line size ,pipe class ,Tracing either heat tracing or steam tracing if there is valve then Valve size and its position i;e Fail open ,fail close TSO AFC etc Then Location of instrument ,then Signal Direction From DCS to Field ,then what type of system either DCS or ESD or FGS etc..and many more..

Could you plz update in detail, like main thing motor related details, like XL, XA, soft tag hardwire tag, details in DI/DO signal, In addition to that, which signal is Control indicating and recording, Indicating, indicating and recording, alarming, controlling, like we use to populate in SPI. You are requested to cover above topic. Thanx

Can you provide cause and effect Matix

make a video on Cause and effect diagram... which signals should be on top and down... is there any phelosphy for C&E

please add part 2 and also include index for motors

Useless document seriously ?

Thanx a lot for such a good knowledge sharing with us🙏

Yes we brief about index

Yes required

Thanks

Indians are the best explainers 🙏🏼🩷

Ohh God !! What an explanation!!❤ Thank You.

Thank you sir 🤝

Asad sir , we understand you are busy in your work , but its humble request can you please make video like "skillset or Things " one should know to join as fresher in I&C offcampus , and what "skillset are required" to get from fresher to senior I&C engineer, I do understand it will really depends on which industry working on but can you please make a video on this as there is no one guiding for that noone , please kindly look into this aspect too, enjoyed all your videos and waiting for Amazing videos , it will give a headstart for freshers what to follow and also resolve most of the doubts.

Thank you.

Not necessarily it's ok if actuator output is higher than MAST, depending on application. The actuator only outputs the torque needed so as long as the valve doesn't jam or isn't subject to more breakout or dynamic torque for the application

Nice sir , LHS cable par bhi video banaiye sir

Very good explanation

Sir bahut bahut best video❤❤❤ love from India 🇮🇳🇮🇳🇮🇳 Truly it's like what I learn in 6 months in a semester you teach more than that in like 10 mins😂❤❤❤ Great video sir🎉

If not FKM then what is recommended for packing?

how to check for passing in vessel bed from I&C point of view ..

Thank you Great presentation. Could you please advise air velocity limits ( min and max) in compressed air systems. And way to calculate them

Thanks for your invaluable insights.

Thx for the information. Hw it is applicable for DI ?

What about self powered instruments

Very helpful

😊😊😊😊

Bhai aap A312/A312M standard specification ke bare me video banao na please

Class VI is possible with metal to metal seating in case of butterfly valves. Few vendors are providing such type of valves. Plz make a video on this.

Hindhi mai batao yar

Thanks

Asad So you mean in liquid cavitation happens before chok flow ?

is it true that there is a difference between PSV & PRV? I read an article about it.

Thanks Asad. Very useful insite on the topic

Very Informative !! Please also make video on leakage class requirement for on-off valves...Thanks!!!

Thanks

Please share about RF admittance level transmitter for interface measurement

Asad can you share as well the difference between ex e to ex eb and ex d to ex db

Very good for learning

cooler way of explaining..very informative