Top 4 Ford Performance Suspensions for Mustang Falcon Fairlane Maverick

  Рет қаралды 56,395

Autorestomod Manic Mechanic Gasoline Media

Autorestomod Manic Mechanic Gasoline Media

Күн бұрын

Top 4 Ford Performance Suspensions for Mustang, Falcon, Fairlane, Maverick, Cougar Comet Montego
Episode 71 Manic Mechanic
Three major types:
SLA (Short Long Arm)
• Stock: Coil over A Arm
Upgrade:
◦ Tubular A Arms for Mustang, Falcon, Fairlane, Maverick, Cougar Comet Montego
• Coil over Through A Arm
◦ Both are non-invasive, will not impact the chassis and can be returned to
stock for Mustang, Falcon, Fairlane, Maverick, Cougar Comet Montego
Mustang II for Mustang, Falcon, Fairlane, Maverick, Cougar Comet Montego
• Used on the Mustang II from 1974 to 78 and Pinto from 1971 to 1980
◦ Improved geometry over stock
◦ Better packaging for engines.
◦ Ample room for engine activities.
◦ The most invasive as massive change are made to the frame system.
McPherson Strut for Mustang, Falcon, Fairlane, Maverick, Cougar Comet Montego
• First used in 1950 on the Ford Consul in Britain.
◦ Improved geometry over stock all around.
◦ With today’s shock technology, arguably the most modern of the three. Still in
use.
◦ With notching kit, engine bay is opened up for activities.
◦ Can be non-invasive, can be returned to stock
Features to look for in aftermarket suspension:
SLA (Short Long Arm)
• Preset Positive Caster
• Changes to the arm to allow for better camber changes (Arning Drop)
• Roller or Del-a-lum pivot bushings
• All can be used with aftermarket racks or steering boxes
SLA Coilover
• All of the features from the Tubular arms.
• double adjustable shocks in the coil-over.
• Ride height adjustable coil-over.
• Most have available rack and pinion systems though you can use aftermarket steering boxes
Mustang II (has camber change built into the system)
• Double adjustable shocks
• Drop spindles for lowering the cars ride height from the suppliers setting if desired
• Brakes
• Engine bay block off plates for the suspension
McPherson Struts (has camber change built into the system)
• Double adjustable shocks
• Adjustable ride height
• Brake options
• Easy to replace consumables (Pads, Calipers, Shocks non-proprietary components)
• Most have available rack and pinion systems though you can use aftermarket steering boxes
Installing a Street or Track Suspension Episode 330 Autorestomod
• Installing the Mustang...
Mustang II suspension in a '66-'69 Fairlane Episode 7 Season 2 Autorestomod
• Mustang II suspension ...
www.manicmechanic.com
www.gasolinemediausa.com
/ gasolinemedia
jford@autorestomod.com

Пікірлер: 151
@RealJerb
@RealJerb 4 жыл бұрын
I really appreciate this episode. This was very informative and answers a ton of questions us early mustang owners have, especially for us restomod guys.
@tomfowler9577
@tomfowler9577 4 жыл бұрын
Love the program!! thanks for all the info!
@coreyjeffords3083
@coreyjeffords3083 4 жыл бұрын
Great vid! Super informative and I immediately went to google to do some more research even though I already just bought and installed my coil over kit. I stuck around until the end as well. Haha you guys are awesome!
@Don14320
@Don14320 4 жыл бұрын
Good job of the explanation on the majority of the after-mart. Keep up the good work!
@davenandalall
@davenandalall 4 жыл бұрын
This is a great series.
@j.anthony3571
@j.anthony3571 3 жыл бұрын
Thank goodness good people like you are around taking the time to discuss these things. Thanks
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
Our pleasure!
@olivercrews8752
@olivercrews8752 3 ай бұрын
Could you do a straight axle on a '69 Ford Falcon
@georgeireson6819
@georgeireson6819 2 жыл бұрын
Great info. Awesome videos
@JARETTZX
@JARETTZX 4 жыл бұрын
Cool video!
@marvinsturgill985
@marvinsturgill985 2 жыл бұрын
Good stuff...I had to use my uncles prosthetic leg for a sway bar....keep educating us..especially we the bottomfeeders!!
@richardgreenlee5359
@richardgreenlee5359 2 жыл бұрын
I did the Australian RRS RACK AND COILOVER McPherson strut conversion on my 71 Torino and I’m amazed what it could do on a roadcourse!
@ericnegron4776
@ericnegron4776 2 жыл бұрын
Loving these videos, recently bought a 63 ranchero so have been watch many of your videos. I am planning to do air ride on it.... have you had any experience with this? I've done air ride on several trucks in the past but never a unibody.
@richardgalli7262
@richardgalli7262 4 жыл бұрын
I want to install a mustang-II front end on my 56 Ford F100 and been leaning to coil overs so the height can be adjusted as you indicated.
@rogerfuller9042
@rogerfuller9042 2 жыл бұрын
Thanks for the videos. It helped with confidence in replacing the suspension parts on my 73 Maverick. INTERESTINGLY... One of the upper control arms were not assembled correctly. The center bar was off center by about 1/4". It was easy enough to remove the outside nuts and get it correct, HOWEVER... could installing (or making) them off center on purpose be an easy way to achieve some negative camber? Have a vendor ship you an upper control arm so you can try it and see how easy it would be.
@derbypreston5547
@derbypreston5547 2 жыл бұрын
Love this one ! It’s a bit complex and I’ve decided I want to understand suspension better before I upgrade
@AutoRestoMod
@AutoRestoMod 2 жыл бұрын
Thanks! It is a little hard to chew at first, but once you dive in, you'll get it.
@67fairlane12
@67fairlane12 4 жыл бұрын
awesome information!!! Im looking to change out my stock suspension on 67 Fairlane. Any advice would be greatly appreciated
@Libslayer
@Libslayer 4 жыл бұрын
Here's a 2nd thumbs up for the camping trip!
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
It has been fun, sadly we have a burn-ban that started yesterday so no fires--no smores...
@jamesshaw89
@jamesshaw89 6 ай бұрын
Cool episode, I had no idea all these existed
@daleelwort7574
@daleelwort7574 4 жыл бұрын
It was good basic info to broaden basic knowledge.
@nogood_ideas
@nogood_ideas 4 жыл бұрын
If you are using the stock style suspension, there is also a "hybrid' coil-over that mounts using the factory spring pocket and shock mount on the top and gets rid of the spring perch on the upper control arm. They also allow some adjustment of ride height, and most of them come with single or double adjustable shocks.
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
Yeah, we mentioned that at about 1:40 in the video. I wonder if that costing is effective with the cost of arms and coil over shock.is it getting close to the cost of a complete coil over? Hmmm I'll have to look at that.
@shogunMR
@shogunMR 3 жыл бұрын
Great information I'm trying to figure out something for my Maverick that's inexpensive but has a better ride for it. Thanks for the insight and helping me understand them a little bit better.
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
Glad to help!
@dollyhorton2579
@dollyhorton2579 2 ай бұрын
I've never seen a gen. 4 camaro/transam set up used,it looks like it would work well in a classic mustang.I have one in my 66 ford f100 p/u .I have heavier springs in it because the 300 six is heavier than the chevy ls motor.Have been using it since 2008 with no problems.I made upper shock mounts from plate steel .Went in pretty easy took me all weekend to make the mounts ,thanks for the info on all the other systems you talked about! I know this is 4 years old now ,but just saw it.
@valmaunton9922
@valmaunton9922 Ай бұрын
Great video. What you recommend for a 16968 Torino GT. I put a 460 in it and would like it to handle better. Thanks for any input.
@aregularfishingguy6203
@aregularfishingguy6203 3 жыл бұрын
CCP has an amazing setup for tubular control arms for the fairlane. Awesome setup!
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
OK!
@charleysgarage
@charleysgarage Жыл бұрын
I really like the TCP coil overs I put on the 68 Mustang, huge difference!
@AutoRestoMod
@AutoRestoMod Жыл бұрын
TCP makes good stuff.
@daniellastiwka6787
@daniellastiwka6787 Жыл бұрын
Thank You for the info, I did not realize there was a strut option. I have a 1966 Fairlane GT with a FE engine. This car was very rough and so a factory perfect resto was not in the books. I am not interested total mods to make more room for headers on the FE. Great review of what is available. I will go and see what the market has to offer. Have a great day, keep it up!
@AutoRestoMod
@AutoRestoMod Жыл бұрын
You are welcome.
@umangu
@umangu 3 жыл бұрын
I have learnt so much from your channel
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
Glad to hear!
@lesheath6216
@lesheath6216 Жыл бұрын
Learned
@steintrostheim4373
@steintrostheim4373 3 жыл бұрын
Great explanations and great videos. I have been spending money on some of these mods and ended up with a RRS full front and rear upgrade. I guess the RRS is addressing the Ackerman angles which are important for cornering.
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
Yes, they do.. It is good stuff. I've driven it and used it in the past with great results.
@ge3m07
@ge3m07 2 жыл бұрын
How’s the rrs been working out? I’m thinking about going that route on my 66
@captainsmate5770
@captainsmate5770 3 жыл бұрын
Good info thanks..1963 falcon..i may do the mustang2
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
That will work!
@mdean73022
@mdean73022 Жыл бұрын
I have the Global West system on a 1965 it is great.
@mavgrab74
@mavgrab74 4 жыл бұрын
I installed Global West arms with Viking coilovers in my Maverick, I like it so far.
@markmeckstroth787
@markmeckstroth787 4 жыл бұрын
Getting ready for a TCI front suspension on my 62 comet, will be putting a 87 5.0 and a AOD here soon. ( Pulling engine now out of a 87 grand marquis). I hope this all works out.
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
You may have to massage the tunnel on the Comet. Even in the later cars I have seen where guys have to mess with the area where the firewall drops into the tunnel to gain clearance.
@markmeckstroth787
@markmeckstroth787 4 жыл бұрын
Ah. Ha! I watched your show on your tranny install in the wagon! Gave me a idea for my swap! Thanks Jeff!
@btu91111
@btu91111 4 жыл бұрын
did you ever do the recomended alignment for power steering on the wagon that you got from Austrailia ? Was so happy to see you get that 4r70w in there with the column shift and bench seat but then i realized that there is no borgeson box or rack and pinion for you Trying to coppy what you did with the wagon but really hate that power assist steering .Did you do the shelby drop or anti dive kit on the wagon i love the wheels , stance and bench seat in your wagon but not sure i could live with the power steering
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
Honestly, if you do the Aussie specs (3 degrees positive camber, 0 camber and 1/16 inch toe, the stock steering is OK. Now finding a SHOP that can do those specs...whoooole nuther ball game. I did not do the Shelby drop on the wagon as the springs had been cut and wasn't ready to drop the nose any more. The Borgeson box is a column shift killer. LOVE the box, but it is just too tight to the firewall to work. Since our Torino is going to be four (or five) speed, we'll be doing Borgeson on it.
@65Coasty
@65Coasty 4 жыл бұрын
RRS in here in Australia make a very nice McPherson strut setup.
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
They do. I like the three link they offer too.
@kevinadcock7700
@kevinadcock7700 4 жыл бұрын
I was wondering about autocross and wider rims and tires on a 62 ranchero. What do you think is the best suspension. I love your videos and thanks for the information
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
Personally my pick is the McPherson strut system. Has the ability to hog out the shock towers if desired, and has some nice handling characteristics.
@trkinwithmikey
@trkinwithmikey 4 жыл бұрын
Stir Crazy
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
Not yet. But I am here 24-7 pretty much. Our house and office are on the same property.
@frankfitz3421
@frankfitz3421 6 ай бұрын
Can you run air bags with mustang ll ?
@michaelmerritt8160
@michaelmerritt8160 2 жыл бұрын
Great program mike from ct
@AutoRestoMod
@AutoRestoMod 2 жыл бұрын
Thanks!
@michaelbutner5771
@michaelbutner5771 Жыл бұрын
How would this help?? I have a 1966 Ford Fairlane GT Cobra with a 429
@aol11
@aol11 3 жыл бұрын
Here's a tip, mazda3 has electric power steering pump for rack and pinion. It can be mounted discreetly for more original look.
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
Yep, there are a couple e-pumps out there now.
@waynehardie7963
@waynehardie7963 3 жыл бұрын
ive got an aussie falcon putting a aussie rrs suspenion kit in not cheap but really good system try rrs web site all bolt in
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
Agreed Wayne, we'll be installing a complete RRS system in our 1964 Falcon hardtop. We are VERY excited about that.
@rossgirdeen3247
@rossgirdeen3247 2 ай бұрын
Does anyone know headers that'll fit a 63 fairlane there has to be something write thanks for the help.
@chrissplace392
@chrissplace392 4 жыл бұрын
Great vid. One question - you said with the 1st 2 options you can use your stock spindles so you can keep the disc brakes. Does this apply to the 6cyl spindles also? I'm working on a 66 6cyl Mustang, currently stock suspension. It's going to be an enjoyable driver & Id like to keep the 4 lug, but a mildly upgraded suspension would be great. Personally really like the behind the scenes, they're fun!
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
That depends...it's a Ford so get used to hearing that...If you are working on a Late 1967 up six, you can reuse your spindles. If you are working on an earlier car, they are different. I THINK the spindle bearing mount hole is smaller. But I'm not sure about that.
@ToneDeafGuru
@ToneDeafGuru 4 жыл бұрын
Wilwood offers a disc brake kit for the stock 6 cylinder with 4 lug spindles, but it's not shown on their website so you'll have to give them a call.
@MichaelEd
@MichaelEd 4 жыл бұрын
Great vid with the comparison of suspensions. Like you said “it all depends on what you wanna do with your car.” The mustang ll was my choice and not only did it open up the engine bay, it also increased chassis strength in my 1965 Mustang.
@MichaelEd
@MichaelEd 4 жыл бұрын
Great read/info in your video description.👍👍
@jeffrob073
@jeffrob073 3 жыл бұрын
I committed to ridetech rear set up. Probably on the front also. Not sure if it has the Shelby drop built in though. Bought the template, not sure if I need it or not. 🤷
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
Me either. Ridetech makes some good stuff.
@elcam84
@elcam84 4 жыл бұрын
I like the classic performance products kit. Basically replaces the LCA and strut rod with a full one piece A arm. Corrects some of the bad geometry because of the strut rod. The rest of the parts are stock. Also the Mustang 2 uses a full control arm on the modern kits and no strut rod. Everybody and their brother seems to sell some sort of suspension replacement kit for Fords. Hmm wonder why... Have fun with the lock down. I am in Tarrant county (Fort Worth) and it is starting to look like we are going to start heading out of it in the next few days. The numbers are stable and low here. I have been getting lots of house remodel work dine.
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
There are SOOOOO many cool options out there now. Glad y'all are getting back to normal over there! Good news!
@elcam84
@elcam84 4 жыл бұрын
@@AutoRestoMod Well we are on the road to what will be the new normal. Starting to see light at the other end of the tunnel and it's not a train coming at us I hope.
@timothyperreault3330
@timothyperreault3330 4 жыл бұрын
I have McPherson strut rack and pinion on my 69 torino and drive very often.
@williamgrant5783
@williamgrant5783 4 жыл бұрын
Good move !!
@C6Wheels
@C6Wheels 3 жыл бұрын
What setup did you go with?
@paul65comet31
@paul65comet31 4 жыл бұрын
I am working with a 65 comet and would like to do an fe swap, that said it's not going to be a drag car but will be a daily driver. I have read that the stock location for the spring or strut at the tower is weak and tends to crack the inner fender due to flexing near the firewall. This makes the bracing necessary, so in my mind this makes the mustang II kits more desirable because then there isn't a need for the bracing. What's your take on this?
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
Watch long enough and you'll hear me say this a lot, "it depends". The cracking can be overcome a couple of ways: the McPherson strut system (non invasive, DIY). If cracked, the tower can be welded, then the Opentracker Racing shock tower wheel side brace kit can be welded in. The Mustang II is a viable option as well. I would want to see it welded in by a certified welder and fab person because your whole car is at stake.
@erikblake3360
@erikblake3360 2 жыл бұрын
I have a 63 falcon and went to replace the tie rods, well the parts I got thru Kar Krafters didnt fit because lo and behold the suspension was changed. Now i am trying to figure out what they changed to. I have been told by some folks that have done ford remods that the most popular change over was to a pinto or grenada. Your thoughts
@AutoRestoMod
@AutoRestoMod 2 жыл бұрын
I am planning a video on that for this week oddly. But to short it, contact me via email: jford@autorestomod.com and send a picture of the tie rods you have.
@philballphotography
@philballphotography 4 жыл бұрын
Im curious to hear from folks who have driven cars equipped with the CPP totally tubular system that adds a subframe plate and eliminates the strut rod, replacing it with a true lower A arm. They have a nice coil over type shock with double adjustable viking shock.
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
I'd like to install one for sure. I have talked to a couple of people that really like it. I think they first introduced it on the Nova (which uses a very similar system).
@jk_navyko9006
@jk_navyko9006 4 жыл бұрын
@@AutoRestoMod I am really interested in doing this to my 67 Mustang. I have been looking for reviews but have not see to many. I would like it if you would do this. Have a great day.
@Levibetz
@Levibetz 4 жыл бұрын
You mention that the McPherson strut "camber changes nicely" this is actually not true, they tend to have very conservative camber curves. This is fine by and large, especially for cruising and drag racing. A good double wishbone setup can be better than a strut. But of course most of these double wishbone setups are confined to stock spindles and pickup points, which leaves the geometry basically unchanged aside from caster. The best setup to look for IMO is a tubular control arm setup that includes it's own specially designed spindle.
@dividingbyzerofpv6748
@dividingbyzerofpv6748 3 жыл бұрын
I can tell you that the Street Or Track front suspension/coilovers took my 66 Mustang to a cornering grip that is nearly equal to my 2015 GT Perf Pack. Once I get the matching rear 3 link/watts link rear kit I am betting my 66 slaughters my 2015 GT. The turn in on my 66 is just nuts. 1.5deg neg camber, 5.5deg caster, 1/16 toe in. 225/45/17 tires all four corners and it grips very well. Only gripe is Unisteer. God they do some stupid shit. Like deleting the holes in the cross member that would clear the lower control arm bolt. I had to plasma cut a brand new cross member because Unisteer deleted the holes that their own instruction manual shows being included.
@65Coasty
@65Coasty 4 жыл бұрын
Detroit Speed make a killer setup. Perfect for pro touring. Very costly but.
@danbytp
@danbytp 3 жыл бұрын
Hey,if it works...
@omaralmaguer2765
@omaralmaguer2765 Жыл бұрын
Which system would work best and not drain my pockets for a 62 ford falcon in-line 6, or would I be better off keeping it stock? Just hopping up the engine a bit, but not a racer.
@AutoRestoMod
@AutoRestoMod Жыл бұрын
You'll need to move to a V8 style suspension on the car as well as V8 steering to get any real improvements. This is due mostly to the fact that all of the components for performance are V8 oriented. Open Tracker Racing will give you the parts that you need to make the front end handle much better at a reasonable price.
@kevins6661
@kevins6661 4 жыл бұрын
Hey how do I make an 03 Mustang GT that's lowered with H&R SS Springs ride smooth.
@CharlieBrown-pb9xn
@CharlieBrown-pb9xn 4 жыл бұрын
Run 15lbs in tires
@danbytp
@danbytp 3 жыл бұрын
I have come to learn through experience and these videos that there are alot of common components between mid 60's Mustungs and mid 60's Falcons. What are your experiences?
@aol11
@aol11 3 жыл бұрын
It's based on the same platform with minor differences. I have 1966 manual power steering from a Mustang on my 1974 Ford Maverick power steering car. Bolted right up.
@danbytp
@danbytp 3 жыл бұрын
@@aol11 Ah,I see it now.
@phonypony5.0
@phonypony5.0 2 жыл бұрын
Back like 20ish years ago I had a 68 cougar that I was street racing at the time and me being a broke kid at the time didn't have money to buy a good disk brake it and rebuild the stock suspension . soo from seeing how my buddys fox body suspension work we went to the junk yard and grabbed the struts spindles rack from a foxbody we had to use fox ball jounts made some ball joint cup out of some scrap pipe weld those in to the stock cougar control arms and made a non adjustable camber caster plate and a few other little odd thing to it work .it really was all that difficult to do and it made it drive soooooo much better suck a old man rear-ended it and totalled it 😢
@AutoRestoMod
@AutoRestoMod 2 жыл бұрын
I agree that sorts of things can be done, but a warranty is nice to have also lol.
@AutoAli
@AutoAli 4 жыл бұрын
I am starting the research now on the suspensions. I thought I knew what I wanted but obviously I don't know what I want. time to decide what my 90% will be.
@danbytp
@danbytp 3 жыл бұрын
Better to find out now before dropping $3,000 and 25 hours into the wrong items and wrecking the car.😁
@AutoAli
@AutoAli 3 жыл бұрын
@@danbytp there’s a whole build playlist by this point on my channel. Feel free to check it out.
@danbytp
@danbytp 3 жыл бұрын
@@AutoAli I'll check it out.Thanks for the info.
@danbytp
@danbytp 3 жыл бұрын
@@AutoAli Just checked out your playlist.It's fantastic!👍
@ralphperez526
@ralphperez526 2 жыл бұрын
My son and I are restoring a 62 Falcon and on a budget. As far as suspension, normal daily driver, what’s your recommendation?
@AutoRestoMod
@AutoRestoMod 2 жыл бұрын
I would do the following: Opentracker roller spring perches, stock upper and lower A-Arms. RRS-USA spherical strut rods. If those prove to be outside the budget, I would at least replace the strut rod bushings. I like QA1 or Viking for shocks, but many find them to expensive. 1-inch front sway bar...though new urethane center and end link bushings for the stock bar can work well too.
@davidsullivan7455
@davidsullivan7455 4 жыл бұрын
Now time for rear suspension options!
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
LOL somehow I KNEW that was coming...
@davidsullivan7455
@davidsullivan7455 4 жыл бұрын
@@AutoRestoMod Well, it's still on my list for my Fairlane. Gotta get rid of the air shocks!!
@9thgatedim273
@9thgatedim273 2 жыл бұрын
I'm trying to build a 1956 ford fairlane and I can't find any information on these cars any idea what's a good front IFS up grade or oem swap
@AutoRestoMod
@AutoRestoMod 2 жыл бұрын
Not a lot out there for this Gen Fairlane. I don't know of any companies doing a suspension upgrade for these. I know RRS-USA offers a rack and pinion.
@GregMottin
@GregMottin Жыл бұрын
I called Wilwood and asked them about the mustang 2 suspension for road racing with an early high HP mustang. The did not recommend it. They said the spindle would flex to much affecting the geometry. Did not say anything about it breaking , but I was under the impression it was marginally strong enough. No first hand experience, just passing along a conversation with Wilwood.
@AutoRestoMod
@AutoRestoMod Жыл бұрын
Thanks for letting us know!
@trailerparkcryptoking5213
@trailerparkcryptoking5213 19 күн бұрын
Need a big block in my ‘62 Ranchero! Need space...
@MissionRestomod
@MissionRestomod 4 жыл бұрын
Check out my AJE coilover McPherson strut install with hand made towers in my 63 Falcon Hardtop @Bag of Bones 1963 Falcon Build on Facebook. No videos yet. Thanks
@hotrodray6802
@hotrodray6802 4 жыл бұрын
Caution: The M II kit usually raises the engine because of the cross member. Not quite as bad as an FE in a 62-65.!!!
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
It does. And that makes for a higher center of gravity. Not good for cornering...of course if you are doing an FE, you probably aren't going around corners except to get to the return road.
@Watch067
@Watch067 3 жыл бұрын
How much higher do you think?
@papkeepcalm8137
@papkeepcalm8137 Жыл бұрын
what about ford granada
@captainsmate5770
@captainsmate5770 3 жыл бұрын
Can you recommend a kit?
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
I really like the RRS stuff. If I am going to go aftermarket, I want a full modern departure.
@Paulie1232
@Paulie1232 4 жыл бұрын
1st again, see I'm waiting with baited breath
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
I even kept the OSB to a minimum for ya!
@Paulie1232
@Paulie1232 4 жыл бұрын
@@AutoRestoMod I love it, lol
@bgaughandodaro
@bgaughandodaro 4 жыл бұрын
Future content...Power steering. How to iron out the squeaks and jitters.
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
Good idea Ben! We'll look into that.
@relaxnewmexico7619
@relaxnewmexico7619 3 жыл бұрын
And thunderbird!
@relaxnewmexico7619
@relaxnewmexico7619 3 жыл бұрын
Yes and the thunderbird
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
Not much out there for the Thunderbird.
@hankfink
@hankfink 4 жыл бұрын
People should know if you want to go around corners don't hack it up and put a Pinto suspension in it unless you go Detroit Speed but then again it's a crime to call theirs just another Mustang II suspension kit. I have a Mike Maier MOD coilover system on my '69 Mustang and kit goes around corners as hard as my 50th LE Mustang.
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
Detroit Speed stuff is on another level to be sure. Like I said there are so many cool kits out there the video would have been five hours long; and I STILL would have left someone out. 😆
@dividingbyzerofpv6748
@dividingbyzerofpv6748 3 жыл бұрын
The Maier racing stuff is impressive. Add Street Or Track to the list. The front suspension alone in my 66 Mustang put my 66 just behind my 2015 GT PerfPack in cornering. Once I complete the rear suspension it will likely obliterate my 2015 in cornering prowess.
@estebanhernandez660
@estebanhernandez660 2 жыл бұрын
Did you get mod 1 or 2 from mike?
@hankfink
@hankfink 2 жыл бұрын
@@estebanhernandez660 MOD1 was the only one out at the time I got it. You can still notch the shock towers too
@ggc87
@ggc87 3 жыл бұрын
I installed some qa1 coil overs on my 69 mustang and it runs like crap. Everything raddled . And I have it on smooth setting .. is it normal?
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
Honestly I haven't used the QA1 set up. I'd give a call to the tech line and talk to them. Here is my email address, we can try and work out the bugs if there is no resolution with QA1: jford@autorestomod.com
@haroldwoods861
@haroldwoods861 4 жыл бұрын
why does almost no one make front suspension for 1962 - 1965 Fairlane?
@hotrodray6802
@hotrodray6802 4 жыл бұрын
These Fairlane suspensions are unique. Nothing is common to other Fords. Not many cars were built. They never were very popular. If it werent for the Tasca T Bolt cars these would have fallen into total obscurity. Briefly: the upper arm is long but bolts into the frame like the big cars. The upper coil sits directly onto the upper arm, like most lower springs/arms do. The lower arms are unique. Geometry is ancient and sux. Ive done several and own 2 personally. Your best improvement is Granada knuckles and modern H+ rated tires. Theres more.
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
RRS (www.rrs-online.com.au/compact-fairlane-parts.html) offers a McPherson kit for that as well as a rack. You'll have to rebuild your lower arms though as they are not yet offering a replacement.
@danbytp
@danbytp 3 жыл бұрын
All of the cars he mentioned in the beginning are all the same under the hoods and bodies.It's a money and distribution thing.I get it.
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
I'd say similar. There were differences.
@danbytp
@danbytp 3 жыл бұрын
@@AutoRestoMod Yes,smilar,you're right.However,I was able to fit a Mustang radiator into my 1966 Ford Falcon without modifying anything.Now that you mention it I remember the guy saying what you said.When the p!rts store referred me to a Mustang specialty place I thought he( the parts store,Auto zone,guy) was crazy.Thats when learned about the common ground of the Ford models of the 1960's-70's.
@williamgrant5783
@williamgrant5783 4 жыл бұрын
Why not just use a Panther chassis swap in a big Ford if you can't tune a suspension .
@roykrossin8343
@roykrossin8343 4 жыл бұрын
Need more Galaxie info
@AutoRestoMod
@AutoRestoMod 4 жыл бұрын
It's coming Roy. I am looking into options now.
@joerandom756
@joerandom756 2 жыл бұрын
So you're telling me I can't put a boss in a 67 Fairlane with stock suspension?
@AutoRestoMod
@AutoRestoMod 2 жыл бұрын
Depends on which boss you're putting in the engine bay. The Coyote 5.0 will be a problem mostly because of the width of the engine.
@joerandom756
@joerandom756 2 жыл бұрын
@@AutoRestoMod 429 boss
@grandebigy
@grandebigy 3 жыл бұрын
👈Ya missed pushrod suspension 😉
@AutoRestoMod
@AutoRestoMod 3 жыл бұрын
We were talking about front suspensions. While there are some rear pushrod suspensions offered, the pushrod won't work up front.
@grandebigy
@grandebigy 3 жыл бұрын
@@AutoRestoMod kzfaq.info/get/bejne/bpOFfchiuqnDh5s.html
How To Shelby Drop
11:42
Autorestomod Manic Mechanic Gasoline Media
Рет қаралды 46 М.
Front Suspension & Chassis Upgrades - '68 Cougar / Mustang
20:43
West Coast Classic Cougar
Рет қаралды 204 М.
MEGA BOXES ARE BACK!!!
08:53
Brawl Stars
Рет қаралды 36 МЛН
ОДИН ДЕНЬ ИЗ ДЕТСТВА❤️ #shorts
00:59
BATEK_OFFICIAL
Рет қаралды 9 МЛН
I Can't Believe We Did This...
00:38
Stokes Twins
Рет қаралды 84 МЛН
A clash of kindness and indifference #shorts
00:17
Fabiosa Best Lifehacks
Рет қаралды 16 МЛН
Making A '66 Mustang Go Straight Down The Road
34:50
South Main Auto LLC
Рет қаралды 228 М.
Mustang Suspension Upgrade RRS
18:47
Autorestomod Manic Mechanic Gasoline Media
Рет қаралды 15 М.
Shelby Drop Explained
8:17
Autorestomod Manic Mechanic Gasoline Media
Рет қаралды 23 М.
Fairlane Falcon Mustang Suspension 1963 1973
10:05
Autorestomod Manic Mechanic Gasoline Media
Рет қаралды 4,8 М.
10 things to know about ford suspension Episode 69 Manic Mechanic
17:08
Autorestomod Manic Mechanic Gasoline Media
Рет қаралды 20 М.
Falcon Suspension Upgrade
12:30
Autorestomod Manic Mechanic Gasoline Media
Рет қаралды 46 М.
The MOD Control Arm for Classic Mustang, Falcon, and Fairlane
2:44
Mike Maier Inc
Рет қаралды 1,9 М.
FORD MAVERICK 302 NEW SUSPENSION PART 1
20:37
ROCKINRONGARAGE
Рет қаралды 364
Странные штыри с кольцами из сарая
0:31
А на даче жизнь иначе!
Рет қаралды 9 МЛН
Почему НИКА решила уехать из дома?
0:46
Привет, Я Ника!
Рет қаралды 2,1 МЛН
Cute ❤️🍭💕🍕🥛🍧🤣
0:11
Koray Zeynep
Рет қаралды 6 МЛН