​I cannot stress how amazing the timing of me finding your channel was. Amazing content dude. Perfectly timed for my first custom build. Happy New year!

Doing this build currently. Been a wild ride when it comes to measurements. Went with the darkside crossflow for tube routing. And the barrowch boxfish for pump res. The idea of using the sidemount for the top rad is genius 👌 I seen this video and you my good sir may have solved all my clearance issues I was thinking I may run into. Thanks 😊

my NR200P just arrived cant wait to finally build in it after falling in love with it from your videos.

Great insights to overcoming the challenges in the case! I have been attempting to figure out laying out watercooling and... gave up. Your videos on air coolers for the NR200 set me straight on what to use. :)

Can't believe Machines & More doesn't have more subs. Incredible content.

I just finished my NR200 build. thank you! u have been a big help since I've never built a PC before

Found this video early 2024 by searching content related with top mounted AiOs in the NR200p and your video convinced me of starting a project on my case. Thank you very much for the all the examples shown in the video

happy new year and thanks for the great stuff. with help from your earlier videosi have already completed my nr200 build but am still enjoying watching along as things get crazy

Working on planning my nr200 loop now. I'm looking forward to the next vid.

Thank you. Stay healthy and a happy new year. CoolerMaster needs to release a new top panel with extra height and different layout to the mesh so we can screw in a thicker top rad.

Nice video, well explained and with a calmed voice. Subbed to the channel. Thx !!!

Seen some amazing inverted motherboard builds that look amazing as well

Fantastic coverage of the various placement choices. TBQH it blew my mind to see you mod it for a top-mount rad. I have the NR200 with a side-mounted PE 240 (NF-F12 fans), bottom-mounted TX240 (NF-A12x15 fans), top-mounted NF-A12x15 (black) fans, Barrow CPU pump/block combo, EVGA 2080 Super HC GPU, and soft tubing with a couple Koolance quick-disconnects. I absolutely love my build but it's very space-constrained compared to yours. Well done.

Really good video, I like the Tsingtao at the end ;)

nice chill presentation

I pulled the trigger and got an xspc 240mm slim rad and slim 15mm fans for a top mount in the nr200p after seeing this video. It works great and can be used without modding the case. I just removed the top mesh from the plastic "bracket" and removed the rubber anti-vibration pads and just screwed the radiator in. I then attached the fans on the inside and it works fine without any interference from other parts. It's got some ~3 mm clearance to the psu extension connector and the ram slots on my Asus Rog Strix x570-i gaming mobo. After I get a new GPU, I will start thinking about making a full custom loop so this channel is gold. It has everything I want and more. Don't change a thing! Subscribed.

Happy new year bro, really enjoy your videos, your talking is very fresh and you make videos very appealing and not boring, hope to see more of you next year.

Thanks for this video! Even if I don't go through with the custom loop in the NR200P I at least got a look at the size comparison of the NR200 and 011 mini :)

Man if I didnt have this video, my mini ITX build would be so much more boring. Thank you so much for your content man! Let me know if you want to see it

Just put a custom loop in mine and gave up on the idea of top mounting the rad. cant wait to watch this.

Thanks for sharing this video. I am glad I went with air cooling ;) I may have suggestion to avoid the PSU mount mod. I used an 10mm long m3 standoff to lower the PSU itself while keeping the PSU cage at its highest position. This way, I was able to mount a 25mm thick fan even with the PSU cage in the SFX-L position. Happy new year to you too!

Just wanted to say that I have mounted the TX240 on top of the case without any issues and no modding: - Remove top mesh - Remove rubber dampers from fan mounts - Mount rad to the top panel - Mount NF A12-15 - Using X570 Aorus I Pro Wifi It just about clears the ram latch and the power supply extension cable Very happy with it so far!

happy new year

Can't wait!

Looks great, cannot wait to see the final product. I ended up using a single rad and really hoping a dual rad solution will be available in the future.

You're bloody fantastic

AWESOME !!!!!!!! GREAT WAY TO START 2021!!!!!! CANT WAIT!!!!!! ^_^!!

I wish they made the case 4 or 5cm taller would make it so much easier

I love the use of that side bracket. I wouldn't even of thought of using that on the top. I plan to add a top radiator, but I am going to try to 3d print an extended top panel making the case ~30mm taller. On the res another good option is the EK FLT120. I have mine mounted to the front of the PSU & it took drilling 4 holes in the included mounting brackets to line up with some that were already in the PSU shroud.

I was thinking it would be cool to see a flat pump/res combo that you could mount behind the front panel.

Currently doing a custom hardline loop in my nr200p with the same pump along with a corsair water block and 92mm rad in the back. I'm only water cool the cpu.

Oh why thank you, Mr. NR200. 😁

To avoid the internal case mods, could the top rad be installed with fans on the outside top of the case?

10:04 oh my.. lol I wonder if Cooler master is taking notes for the next case

i have a barrow cpu block pump for my desk pc loop which has a cpu gpu 240 and a 360 rad and its been doing great

SuperVideo. What a reference channel for this SFF theme. Finally and afrer many dudes i get a h100i Corsair Capellix for my Ryzen 5900 and i will put in the side panel. This option makes impossible the use of the tempered cristal panel. Would fit this Corsair AIO on the top?. Happy year!!!

Oh, this video is sponsored by Tsingtao beer. Cheers, Happy New Year.

I was able to use the 280 and rad bottom with using the iceman res on the back of the case.

Hey I've watched many of your videos but unfortunately can't recall if you covered this, so here goes. The two sickleflow fans are producing a resonance, not in the sense that most people have reported with this case (usually it's more of a clicking), but for me the case is transmitting their rpms as a very audible, pitched hum. I am wondering if this is an issue with the case itself, or if I would still be fine with the usual solution of switching to noctuas. Thanks so much!

Love the content on this case as always man. A quick one, as you can easily remove the top mesh surely this means you can add any fans you want at the top? I gather you just need to be very careful if screwing fans in, as the mounting material is plastic? Thanks

I feel u should do a video on how to invert the NR200 so that the rad can be on top :)

Does a 92mm fan in the rear as intake/exhaust help at all with a top aio ? Should the top aio fans be set to intake or exhaust if using the 92mm fan?

Did you configure the top rad fans as intake or exhaust?

Do you think cards like the XFX 6800 at are out of spec for the case(Length 10mm over) can fit into the nr200p? Mods or not? I assume cable management would not be the best in that circumstance but regardless

Hey love your videos! I am planning a similar build and using the Barrow Pump/Block combo. Just to clarify in your video you mentioned that the 2600 pump is weaker. Were you referring to the Barrow combo unit or the Alphacool DCLT? Also you can definitely lower the PSU with 4 standoff screws instead of cutting the PSU shroud mount. But I prefer to dremel as little as possible.

Nice mod- not having a default top radiator mount option is the only thing that turned me away from this case. Funny thing is I ended up going air-cooled on my Sliger S620

Hi. Need to ask, what is the clearance from top of PSU to top of casing? I plan to mount Kraken M22 on top of PSU area. Help me

Now that you are cutting on the case, I wonder about placing the PSU on the front panel mounting slots with a hole cut in the interior panel to allow the PSU to face away from the case interior intaking air from the front of the case. Of course the exterior front panel would need to have ventilation slots or holes added for PSU intake air draw.

Have you looked at the top had mod kits for this case ?

ive a feeling an FLT120 with a D5 would fit on that psu shroud and not be too big as to hit the case.

happy new year from france, was planning this setup with the small pump res from corsair.....and i am very confused.......doesn't the pump have a bracket or standard mounting hole ? i don't want to put holes in my new case XD

you can just use mobo stand offs to lower the psu,then you can screw normal screws into the standoffs

This guy is fkin epic

Would be interested in seeing how this could fit with a vertical GPU if it fits at all.

I know you did this a while ago but I have a question for you: could you modify the motherboard mounting bracket to move it lower to fit an AIO up top? I have a dual AIO setup and would like to try this case. I am thinking of modifying this motherboard bracket to lower it down, lowering GPU clearance to 2 slot but then allowing me to fit the side rad and also a top rad.

i used a 3800x and 2080 super 240mm on bottom with fans mounted under case with 3d printed taller feet 45mm and a 92mm rear rad and my temps under load under 65 and in 50s gaming i used thick 92 mm and mounted that fan outside too use a temp sensor for fan control this thing is silent

from all these builds i see online i dont see anyone doing a water build with the vertical gpu setup and a thicker radiator on the bottom. like a 40mm 240 rad and regular 25mm fans which should clear the pcie cable and then using the borrow cpu/pump/res combo, throw in some soft black tubing and quick release connectors and call it a day.

Can you please show us if a front mounted HDD is possible (behind the front panel where two 2.5 ssd can be mounted) in default case settings? if not then what should be the mods for that? #TIA

Can i ask, if the 240 on top rad is too deep that would hit the ram lach, how about 120mm rad... So botom 240 + 120 should be enough for my 10900k and rtx 3080?

That o11D mini teasing us in the back 😏

Hi there will this mod work with an Aorus B550i? I don’t want to buy it just to find that it doesn’t work 😓😓

This is amazing! I hope CM is taking notes and allows the v2 NR200 (NR210?) to allow moving the rad mount between the side panel or the top. Also, if you were using an integrated block/pump, could you do a 240 + 240 + 280 triple rad setup? Maybe less for looks but for raw performance.

Hi, do you know the difference between puttings fans as intake on the outside of the radiator vs inside? side mounted AIO style.

will this work for nr200p?

Part 2 when?

with this mod, is it possible to mount a 240mm aio up top?

Vertical gpu with barrow pump res combo and bottom rad Does this fit?

I wonder if it would be possible to mount 2x240 (top & bottom) and a 240 or even a 280 on the side?

First of all, thank you very much for this interesting video :) 1. I hope that the upcoming liquid cooled build that will follow these mods will have some high end gpu such as 3080 and also cpu such as 5900x, since I don't think that anyone with lower end gpus/cpus would put so much money into custom loop, so please if you could do a benchmark of these parts or even high ones(3080/5950x) I would really appreciate that 2. Have you seen the 17mm 240 cooper radiator that you can get on Ali or Taobao ? What do you think about it in terms of cooling and would you think it would fit without mods to the case when combined with 15mm noctuas ? Could you maybe do a comparison of that radiator to the TX240 (both in top position) as a secondary radiator to the bottom one (so 2x240 rad build) ? 3. Also on Ali you can actually find only 12mm high fans, do you think that those would make TX240 fit without mods ? Or if not, then maybe with the before mentioned 17mm high rad, so that you will essentially get just a 29mm high solution ? 4. Do you think that the barrow cpu/pump block combo can handle 2x 240mm rads + cpu + gpu blocks with somehow not disturbing noise(I mean not pump on full throttle) ? Sorry for such a long comment and many questions :)

What if I don't Mind a side mounted radiator?

Why not use the Tecware Fusion?

Would set up work with a Crosshair Impact? Not sure about ram height.

Does dropping the PSU shroud make it more difficult to fit PSU cables into the storage between the PSU and gpu?

can nt be easy just move motherboard 50mm lower and make new 4 mounting holes and cut out from back aol shield as well. I got this idea, but my case is coming, after long time searching i choice this nr200p, but was thinking about Jonsplus i100 Pro, but deside i want something smaller.

Cooler Master - We introduce the NR200P. An ITX case with seemingly unlimited modularity to fit every cooling need. Machines & More - Hold my beer.

First of all, thanks for all of your content, I am actually building my own custom loop with a NR200p and your videos are really useful. We have almost the same build ( same MB, same PSU, same RAM...) and during my tests for mounting a top radiator, i end up strugling with some connectors, especially the D-RGB / RGB connectors. So my question is : Is it enough clearance for the D-RGB and RGB connectors with your mod ? Or is it really tight ?

Not being able to use a regular rad on the top sucks hard (for me). I have a Corsair 240mm AIO and as GN said, bottom mounting is terrible for the life of the rad. Also side mounting the rad hides everything. Might have to sadly go with an air cooler for this one 😢

and i have an sfxl, to big to what so ever. im think of moving the psu to the front, and in the place of the psu put an 140mm fan to suck all the air off and do some help to my msi gaming x 5600xt wich also is to fat. to vertical gpu and bottom aio im looking for EKWB MLC Phoenix 240

if you have both rads in series restriction only counts as 1 rad fyi

I still want to see a mod for a 280 rad on the bottom.

You can use this kind of "all-in-one" solution from Barrow as cpu water block + pump + reservoir: www.aliexpress.com/item/10000411453657.html, it's mentioned in one of the Optimum Tech videos kzfaq.info/get/bejne/iah5isp80t3WZmw.html but it has some flaws: the mounting screws are falling through the springs and needs some washers to prevent that; you need to buy a cap for filling port (also fittings not included); you will unable to fill it properly until you buy some 90deg adapter to filling port as shown in his video. Currently I building up kind of custom loop with this thing in nr200p. Actually it's my second attempt, the first try was fail, because I didn't consider that the soft tubes not that soft as I thought, lol. For now I will just put one 240 rad at the side, and hope it will be enough for 5900x. Sadly I can't find that XSPC TX240 rad in stock anywhere, would like to use it as top radiator with custom hat mod like this one: worklogs.coolermaster.com/topic/28848-nr200p-addaptation-for-rtx-3080/ Lately I will consider watercool my 3090 Suprim X and will look at 3 rad setup in this case tho. The card barely fits despite it out of spec in length and its f*cking hot, so I left my side panel open all the time so card be able to blow all hot air out of case. Great content btw. Cheers and hello from Russia!

Wait, Tsingtao makes a stout!?

yo !! hey check this out !! i may have found a way to mount the XD3 pump without mods , the psu bracket !! you know how the back of the psu have those holes ??? well turns out that you can fit ( with a washer ) screws to fit the 120 mm fan mounting bracket included in the box with the pump/res, because the engineers use even numbers, i had a feelings this could work ! if you can test it and it fit, well good luck !

Hi there, I've been watching your videos for quite some time and it made me decide to upgrade from my 900D tower to NR200! I just love how it looks and want to upgrade my old PC. Originally I was planning on getting 5900 + 6800 XT (Stock is available in my country for any card 6800 XT/3080) with U12A 2 top fans and 2 bottoms fans. In your previous videos you've mentioned that C14S would provide better results but that would only allow 1 top fan (A12x25) with that said 6800 XT is huge in height and will allow only A12x15.. Would you still favor that setup (C14S, 1 top fan, 2 bottom a12x15 or it would be better U12A with 2 top fans ? Would 3080 be better with 2 A12x25 at bottom? Why did you move back to U12A ? Your opinion would really help, thanks in advance!

MO-RA3...this is what you need to know

I don't get why you went through the trouble of fixing the rad to the top, but then stuck one in the bottom as well. I think it would be better to move the mother board bracket and everything else down so that there is plenty of room for a rad at the top, that way you wont need the rad at the bottom that is taking up space.

the EK-Quantum Kinetic FLT 120 DDC PWM D-RGB would fit better thats the way i will go in my nr200p

Bottom mounted radiator is the worst solution possible because air collects in the highest point what’s the pump with a bottom mounted radiator.

Thing is, top mounted Rad would have solidified the NR200. We shouldn't need custom fittings to do it.

make the panels inverted will also work, and easier to mod: kzfaq.info/get/bejne/ZrGEiM9-t9PDg6M.html

your videos are good but painfully slow