Toro Power Max HD 828 OAE Assembly and Setup

Рет қаралды 34,447

Күн бұрын

In this video, I go through assembling and setting up the Toro Power Max HD 828 OAE Model 38838.
If you buy this from a dealer it will be set up and ready to blow snow but If you buy it online it will need assembly. If you buy it from a big box store it will be assembled but still needs to be set up.
Use the links below to see more and buy online: (I make a small commission when you purchase through these links)
Compete Toro article at movingsnow: movingsnow.com/2020/2020-toro...
Buy from The Home Depot: imp.i284638.net/dx7XK
Buy from ACME Tools: imp.i284638.net/2OdkD
828 to 928 comparison - • Toro 828 928 Comparison
Toro 928 OAE Steering Problems? This fix works for all 2-stage snowblowers! - • Toro 928 OAE Steering ...
Recommended: New! 28" (71 cm) Power Max HD 828 OAE 252cc Two-Stage Electric Start Gas Snow Blower (38838)MSRP: $1,299.00 USD This is the new "economy" version of the Power Max HD. It will handle just as deep of snow as the other HD models - it just won't do it as fast. I predict this will be one of Toro's most popular models! No, it does not have hand warmers and you can't install them. Will not clog on heavy, wet snow!

Пікірлер: 167

@PaulSikkema 3 жыл бұрын

Feel free to leave a comment below. (I do moderate the comments so it may not show up right away) Thanks for watching and please Subscribe!

@kenmayer3785 Жыл бұрын

Ty for your service! Very helpful with your added insight. Appreciate

@Peter-976 3 жыл бұрын

When it comes to snow removal machines, your channel is what I base my decisions on. Thank you for the honest content.

@PaulSikkema 3 жыл бұрын

Thanks 👍

@jessehuston8264 2 жыл бұрын

Just bought one today after watching several of your videos. It will be delivered tomorrow from my local dealer. Thanks!

@PurpleCollarLife 3 жыл бұрын

Hi Paul - great video! We love our Toro 828! Got to use it this week twice in 10-16 inches of snow. It works amazing. Better than I could have expected.

@judicronin518 Жыл бұрын

Such great information Paul. I had the skid shoes replaced with the composite shoes because this snowblower did scape up the driveway. You also did a great job explaining what causes this snowblower to pull to one side. Thank you for making this informative video.

@mct8888 3 жыл бұрын

Setup and delivered by the dealer was the right choice! Can’t wait to use my 928!

@stutalley8296 Жыл бұрын

Getting ready to buy, You have been the best source of straight forward info mixed with a ton of experience. Thank You for sharing with all us snow rookies

@KnitStyle 3 жыл бұрын

Thank you so much for this video! It was very helpful. We just got this set up, still a lot more snow to come in the Northeast! 💕❄️

@claudiasmith039 2 жыл бұрын

Thank you so much. I got one sitting in my garage assembled. But don't know to use it. You were very helpful.

@barkobama7385 Жыл бұрын

Thanks for the video, I appreciate the walk through, really helped me out getting assembled and up and running quickly

@ComeOnPeopleThink 2 жыл бұрын

I've been reserching snowblowers for the last several weeks now , watching whatever reviews comparisons and demonstrations i could find and it's more than obvious that this guy is the only person you can trust that he really knows what he's talking about..btw i bought the Toro power max HD 1030 ohae...

@jnmcs 2 жыл бұрын

Waiting for my new Toro to be delivered. Very helpful video, thanks!

@johnsikora6043 3 жыл бұрын

Another great video. I can't wait to see your review after you use it.

@echocharlie9812 3 жыл бұрын

thank you for this very informative video...Cheers from Maine I just got one from your review i had a 928 from 20 years ago both are mounters

@nathankern2236 3 жыл бұрын

Just picked up a toro power max hd 1030 ohae. What a beast it is. Happy with the 30 inch size and the 10 hp motor is great. I think this will be a major seller for toro.

@curtiscummings4399 3 жыл бұрын

Wondering if you had a chance to use the 1030 yet. I purchased one yesterday. Thanks

@treblader5699 3 жыл бұрын

Great video Paul and love your content. Keep it up!!!

@VolrathMTG 6 ай бұрын

Thank you for the detailed video!

@douggracy2909 3 жыл бұрын

Nice looking machine. I have a John Deere TRX26 with rubber caterpillar style wheels. Bought it new about 32 years ago and still looks like new. Plows through some deep stuff and throws awesome. I added electric start to it about 15 years ago. Don’t see these track type throwers very often. Smartest decision I ever made getting the track style.

@PaulSikkema 3 жыл бұрын

The crate behind this one in my garage is the new Toro Power TRX. You'll get to see it soon. I'll also be reviewing the Ariens RapidTrak after that. Your TRX26 is a beast and goes through anything but the new ones are a lot easier to use.

@douggracy2909 3 жыл бұрын

I can’t wait to see the new Trax. I bought mine when I lived in Garden City,KS (western ks) and I woke up to 3 foot snow drifts in my driveway. Game on at that point!

@IRONMAN79101 Жыл бұрын

Thank u my brother this was very helpful

@PrincessCutLawnCare 3 жыл бұрын

Nice in depth unboxing Paul! Just did one on this machine myself:) look forward to our results this winter ❄️

@PaulSikkema 3 жыл бұрын

Thanks, You can check out his video here: kzfaq.info/get/bejne/bpOWa6ik3rLbnGw.html

@PrincessCutLawnCare 3 жыл бұрын

@@PaulSikkema Thanks for posting the link Paul:) i appreciate that! nice to connect with you by the way im george:)

@thegrumpyolddad. 3 жыл бұрын

Big help, thanks for the video.

@RobBrandtWoodturning 3 жыл бұрын

HI Paul, thanks for the great video, I am just busy setting up my new blower, which is missing the clevis pins and washers, and wanted to see if anything else was missing from the box. Ended up watching the whole video and subscribing. I will see if I have any cotter pins to get it going. Keep well, Rob

@johnycano9262 6 ай бұрын

Thanks that video was a big help

@symbionesesla Жыл бұрын

Love the video! Thank you!

@AStanton1966 3 жыл бұрын

You did a nice job; I learned some things about the newer blowers. I just put a Chinese carburetor on my old Toro Powershift. It was about 10% of the cost of getting the thing rebuilt. I think you should of talked about the new alcohol-free gas for small engines.

@PaulSikkema 3 жыл бұрын

TruFuel and other alcohol free fuels have been around now for 10 years. I've talked about the at movingsnow.com. The fuel is terribly expensive but worth it for off season storage.

@stephenschelb6503 2 жыл бұрын

Thank you for this video - very helpful! I just bought one and I can't stand the "picture book" instructions...much easier to watch it be done!

@alans.4658 3 жыл бұрын

Thanks Paul!

@Rowebote 3 жыл бұрын

I just got the 828 OAE earlier this month to replace my old Poulan Pro. Got to use it once already. Great machine but the pull to start is so much less than what I'm used to or expecting! You don't need to really need to put a lot behind it to start it.

@PaulSikkema 3 жыл бұрын

Yes, the Toro engines use a compression release so it's very easy to pull-start them. Even the 420cc pulls easy enough that most people can start it.

@brendo8046 3 жыл бұрын

So I just assembled mine with this helpful video. Engine starts up, wheels move, but my auger won’t engage. Any suggestion? Is there a safety switch somewhere? Thanks

@isaiasflores2073 3 жыл бұрын

THANKS FOR VIDEO

@phillynch4971 2 жыл бұрын

bought the same one but the chute was not already assembled.

@smiley3303 Жыл бұрын

You are great!

@umairahmed3117 3 жыл бұрын

Hi sir wanted to purchase a snow blower 2 stage have 2 car driveway want to know which toro machine is good for me to purchase thanks

@BartStar009 3 жыл бұрын

Paul? you need to adjust the shoot deflector cable at the shoot clip-holder, and the other end of the cable that goes to the quick-stick needs to go above the top horizontal handle instead of below it. I don't think it's the paint on the hinge

@PaulSikkema 3 жыл бұрын

The shoot deflector cable is not the one I attached to the rod. The deflector cable runs down from the handle, is attached to the lower transmission case and then up to the deflector. It's mounted that way so it doesn't bind. It's the paint, I didn't move the camera but you can see the extra layer of paint on the hinge that will wear off soon.

@gspringer4 3 жыл бұрын

Excellent video, thank you. Do I need to purchase ethanol free gasoline to prevent the carb from gumming up?

@PaulSikkema 3 жыл бұрын

I use 87 Octane E10 fuel and add 2 tablespoons per gallon of SeaFoam to mu fuel can when I go get gas. That keeps the carb from gumming up.

@frejac1326 2 жыл бұрын

Excellent video. Just received my Toro Power Max HD 828 OAE today and I am wondering if there is a way to adjust the deflector so it points a little down?

@PaulSikkema 2 жыл бұрын

Not that I know of. My nephew used the 928 last year with the double chute and is now complaining about the chute on the 828. He didn't realize how much of a difference the was.

@williamhazlett6724 2 жыл бұрын

got the same problem the chute wire i took off and it was all twisted and didnt move got no controll over up and down on mine might be a problem with these

@samsacre4304 Жыл бұрын

Im rewatching you videos big big thank you! I bought 828 last year new at local Ace hardware, do you pump tires hard or is half flat better for traction???We get 60 plus inches per year !My scraper on bottom seems to grab and makes it hard to keep it going straight ANY advice??? Thanks for great videos! Big thumbs up!

@PaulSikkema Жыл бұрын

You want the front housing resting on the skid shoes - not the scraper bar. Start with an 1/8 inch gap. Put the snow blower on a hard surface (cement). Put two paint sticks under each side of the scraper bar (1/8 inch) and then loosen the skid shoe bolts. Let the skid shoes drop down and tighten the bolts. Does the scraper still catch? If your driveway/sidewalk has a lot of cracks and bumps you may have to raise the gap to 1/4 inch. If you are clearing gravel that hasn't frozen yet you may have to increase the gap to 3/8 inch If you are clearing loose gravel (pea gravel) or a lot of turf (area for your dog) you may have to increase the gap to 1/2 inch In other words, keep increasing the gap between the scraper and the surface until it stops grabbing - most of the time. I have a few 1/4, 3/8, 1/2 thick 4X4 inch plywood scraps that I keep around to set the gap. What little snow you leave usually melts off the next sunny day.

@ajrollan5304 3 жыл бұрын

Hi Paul can you recommend me a 24 in two stage blower. I’m looking at the Ariens platinum 24 or should I go for a husqvarna st324, thank you, stay healthy

@PaulSikkema 3 жыл бұрын

Between the two - buy the Ariens. You will be very happy with it 20 years from now and your neighbors will still be amazed at how far it throws.

@a3medialive 3 жыл бұрын

The gas linkage think broke on my brand new 828 cable pulls the rod going into the blower but it feels like it's lose

@PaulSikkema 3 жыл бұрын

Get it back to the dealer and have them fix it for you.

@joepoe8861 3 жыл бұрын

Great vid Paul. I just got the 826 power max and I am having trouble with the chute staying in place. If I move it so it shoots out to the left , it will move on it’s own to the right. Any suggestions before I tinker with it?

@PaulSikkema 3 жыл бұрын

Pull the cover off the gearbox out by the chute. Make sure the cog is engaging to hold the chute in place. Also make sure the blue button on the joystick is lifting back up completely. I take the cover off and show you how it works in this video kzfaq.info/get/bejne/qLSBh6Z13c65ZWg.html If that doesn't work see you Toro dealer

@joepoe8861 3 жыл бұрын

@@PaulSikkema thank you for the reply Paul. I ended up returning it to Home Depot since it’s been only two weeks and upgraded to the model with the heated handles since that’s the only one they had. There was definitely something wrong with my first one because I compared it with the one I have now so I am glad I did that without any problems to switch since it was under thirty days. Thank you for the quick response. Be well.

@timshannon3909 3 жыл бұрын

Paul, I purchased a new 1030HD and during the first storm our road was very soft and the plow pile had a lot of rocks in it. Long story short, I had rocks get jammed in the impeller and the machine never cut off. Now when I try to use the machine, it barely throws snow. What do you think this may be? My thought is a new auger belt, but is this machine faulty for not cutting off under a jam like designed? Thanks!

@PaulSikkema 3 жыл бұрын

You most likely stretched the belt. Watch this video on how adjust the impeller belt. kzfaq.info/get/bejne/gJtzY8mAtMuZmYk.html If it won't tighten up then you'll need to have your Toro dealer install a new belt.

@Edbone410 Жыл бұрын

Hey Paul I'm looking at upgrading, between toro 828 and the cub cadet 3x 28" I know the toro has a bigger impeller but the cub has a bigger engine, we get about 80 inches of snow a year

@PaulSikkema Жыл бұрын

I don't recommend ANY 3x snowblower. They don't handle snow as well and have issues breaking the shear pins on the 3rd stage. If you regularly get 12 inches or more at a time I recommend the Toro 1428, Ariens Deluxe 28 SHO or an Ariens Pro 28. The larger engine make clearing snow a LOT faster.

@Edbone410 Жыл бұрын

@@PaulSikkema thanks Paul, I have a home depot credit accout so unfortunately it limits choices, if they carried ariens I'd get the deluxe 28 sho

@traviscade3186 3 жыл бұрын

Brought the 1232 OHXE mid September at home depot because it the was priced wrong for the 928 OAE saved over $500. You started in video that you had another video on setup? I could not find that video. Do you recalled the name of that video? Btw Thank you for another great video!

@PaulSikkema 3 жыл бұрын

Toro 928 OAE Steering Problems? This fix works for all 2-stage snowblowers! - kzfaq.info/get/bejne/pNGaf5tltcWppYk.html

@larryroberts8164 6 ай бұрын

For this electric start it only works while plugged in right? Meaning it doesn’t have a batter that maintains a charge while you have it plugged in?

@PaulSikkema 6 ай бұрын

Correct. 110 volt plug in electric start.

@bobalijon Жыл бұрын

at 16:52 you say to use 5W-20 Synthetic oil for the engine, however the manual (page 20) suggests if using "synthetic" to use 5W-30. Can you explain why I should use 5W-20 instead? Sorry, 1st time snowblower owner and not experienced with oils either. Thank you. Great video btw!! Helped me tremendously with putting it together!

@PaulSikkema Жыл бұрын

I mis-spoke. It should be 5W-30

@Jagon_S 2 жыл бұрын

Have you ever needed to install the 144-1620 HD Drive Link Kit for this blower? I've read some reviews, and it seems like the original linkage breaks quite often. Just received my unit today and was surprised it has the original linkage. Just found your channel today. Subscribing!

@PaulSikkema 2 жыл бұрын

I talked to a large dealer and he said, "Out of the last 400 HD snowblowers sold only one broke that rod."

@thomasdowell4368 2 жыл бұрын

Would you recommend lock tite on the handle bolts

@PaulSikkema 2 жыл бұрын

The blue Loctite is always a good choice for equipment like this. The nuts on the handle are all locking nuts so they don't require a thread locker though.

@CRD53 3 жыл бұрын

Thanks for your videos Paul. I picked up the 828 power max HD at a auction ( I probably shouldn't say for how much because folks will be shocked). I don't believe it was used, as it still had wrappings on it. It was completely assembled and everything seems to work just fine, except for one thing. It seems that I have the same amount of reverse positions as I do forward positions. Is there a adjustment for that?.

@PaulSikkema 3 жыл бұрын

Look at the shift lever under the dash. There is a threaded rod that goes from the shift lever down to the transmission. Adjust the threads so the reverse works the way you want it to. You can watch this video to see how the transmission works: kzfaq.info/get/bejne/gd6IqLGLvKqwiZs.html

@CRD53 3 жыл бұрын

@@PaulSikkema Thank you Paul, I think that is just what I needed to know. You are a great resource.

@larryallen5473 Жыл бұрын

I have the OAE28, is there a removable scraper blade or is it integral. Mine has no attachment and I'm wondering if it just needs adjustment on the skids. It does not clean to the pavement surface. I can send photo if you have a way.

@PaulSikkema Жыл бұрын

I answered this question with the other question you asked. Adjust your skids shoes so that the gap under the scraper bar is 1/8 for hard pavement or 3/8 inch for gravel. That way it will clear the snow bout now catch on every crack in your cement. The little that's left will melt right off when the snow comes out.

@deaconpladek Жыл бұрын

Paul, one final question; is the HD 1030 a real jump in product quality and durability, or, is it just a close cousin to HD 828? Even a comparison link is appreciated if you know of one that compares

@PaulSikkema Жыл бұрын

The easy way to explain: The 1030 is the same machine. It's just two inches wider and has a larger engine to compensate for the extra width. Same quality and durability. You have to go to the 1428 to get the commercial features.

@kenmayer3785 Жыл бұрын

My coworker has a older model toro with a plastic chute, mine is your model brand new, do you do anything special after you use it as far as cleaning it? Someone told me to spray chute also. Ty for your video and service

@PaulSikkema Жыл бұрын

If you are running dirt or mud through the chute you may want to clean it when you are done. Otherwise the snow doesn't stick inside these new chutes (or the older poly ones) Toro snowblowers have a lot more "throw" than older snowblowers and some of the other brands. Snow really doesn't stick in the chutes - even when the snow it really, really wet.

@kenmayer3785 Жыл бұрын

@@PaulSikkema Thank you, that is helpful

@mngzhx 10 ай бұрын

I just bought one. when I link the lower knob with upper right hand tigger I fond the lower knob is stiff and cannot be up/down movable. Is this difficient or there is something or pin to unlock it?

@PaulSikkema 10 ай бұрын

I don't quite understand. Is it the speed control lever or the chute control. If you mean the chute control you may have to remove the black cover by the top of the chute and look for something binding.

@KC1PSK 2 жыл бұрын

I used mine today. The handles you grip are way too tight. My left hand was cramping holding it. Is there an adjustment?

@PaulSikkema 2 жыл бұрын

Yes, Adjust the left cable as shown in this video. When the handle is up you want it to flop around. When the handle is engaged you want it to expand the spring about 3/8 inch.

@user-ju5rn5rm8l 6 ай бұрын

Trouble shooting my 828 OAE. The two stage cuts out. I changed the auger belt, not he issue. Worried it’s a “no shear pin” disengagement failure or possibly auger bearing failure. Can you explain where that “no shear pin” disengagement takes place? Thoughts?

@PaulSikkema 6 ай бұрын

It doesn't disengage - either the belts slip or it kills the engine. Your problem may be as simple as a cable adjustment. When you engage the auger lever the spring at the end of the cable should expand about 3/8 of an inch.

@randallzook5570 Жыл бұрын

Love your videos Paul thank you. My question in on starting at full throttle, is it not better to start at idle to create less wear on a cold engine? I notice that all videos start at the rabbit setting which makes me cringe.

@PaulSikkema Жыл бұрын

I understand your concern. With the exception of the EFI engines all the snowblower engines use a fixed jet carb and they just start better on full throttle. That said, I start them on full choke, full throttle and as soon as it starts to smooth out I'll reduce the throttle and let it warm up and 1/4 to 1/2 throttle.

@randallzook5570 Жыл бұрын

@@PaulSikkema Thanks Paul appreciate all of your videos. I just bought the Toro 828 today. It was a tough choice between that and the Ariens that you compared side by side in another video. For me the joystick was the deciding factor love that design. Keep the videos coming.

@easyray7621 3 жыл бұрын

I have the 928 HD which is a great machine, but do you know why they changed it to 8HP.

@PaulSikkema 3 жыл бұрын

They didn't change the 928. They added the 828. My next video will explain the differences.

@Moadar 2 жыл бұрын

I just got one of these my manual says put 5w30 in but you are saying 5w20 synthetic. Why doesn't the factory manual recommend synthetic?

@PaulSikkema 2 жыл бұрын

5w30 is the correct oil. The chart on page 20 of your manual for this model can be little confusing. It shows that you can use 5w30 synthetic under all conditions and temperatures. If you are using regular oi you should use 10w30 for temperatures above freezing and 5w30 for temperatures below freezing. If you have an older snowblower and it does not show synthetic you can still use it instead of regular oil.

@rf005 Жыл бұрын

I have the 824 oe powermax and my differential when I turn the wheels drag there is no trigger less steering and it is a burden not sure why it doesn’t turn easier

@PaulSikkema Жыл бұрын

The PowerMax 824 gas and the 824 oe electric do not have a differential. They are solid axle machines.

@chrisdomenici9107 2 жыл бұрын

What are the dimensions of the box? Just wondering if it would fit in a 4 x 8 trailer.

@PaulSikkema 2 жыл бұрын

36X60. Yes it will fit on your trailer

@leanjason4 3 жыл бұрын

So I just purchase one of these. It seems that the blade never disengages. It starts with electric start but not with the rope, I think this is due to the blade being engaged. How do I adjust the blade engage trigger?

@PaulSikkema 3 жыл бұрын

My first guess is the cable is too tight. Watch this video starting at the 5 minute mark. It shows you the proper tension on the cables. kzfaq.info/get/bejne/eJ6ZdsucrdCxgac.html

@leanjason4 3 жыл бұрын

@@PaulSikkema thanks, that worked!

@ajrollan5304 3 жыл бұрын

Hi Paul is this machine comparable to the ariens platinum ? I found this same model on sale for$800. Ty, I enjoy your video.

@PaulSikkema 3 жыл бұрын

Not really, It is very comparable to the Deluxe 28 SHO. Be careful about that $800 snowblower. It can't be new for that cheap. If it was at a box store it's a return and there is probably something wrong with it. If you know someone who knows snowblowers take them along to make sure you are not getting a dud.

@ajrollan5304 3 жыл бұрын

Thank you I will take your advice

@jandksolutionsllc3663 3 жыл бұрын

Hello Paul - Have my Toro hd 828. All set. Live in Southern Minnesota. Got our first snow to use it overnight. Cold (-4). Got to use it and the chute will adjust up/down, but not side to side. Did it just freeze up? It moved as I messed with it before. Any ideas? Is this common? Appreciate any help you can provide. Thanks.

@PaulSikkema 3 жыл бұрын

1. Make sure you are squeezing the blue trigger on the top of the joystick all the way. 2. Did you buy it from a box store? Remove the black poly cover from the gear assembly out by the chute. See if the latch that holds the gears releases when you push the blue trigger. If the latch is not moving follow the cable up under the dash and make sure it's connected to the joystick. Here is a video where I show you how it should work. kzfaq.info/get/bejne/qLSBh6Z13c65ZWg.html

@jandksolutionsllc3663 3 жыл бұрын

@@PaulSikkema Thanks, Paul. It finally started working freely. The blue trigger was moving prior to today. This morning the chute was adjusting up/down, just not side to side. I guess it was frozen. (-2 here). This was my first use and it had bee kept in a non-heated garage. It moved freely before. However, once it started working, it wouldn’t stay locked in place unless I put slight upward pressure on the blue trigger. Then I could hear/feel it lock. But it would release again every time I moved it. Very annoying. Hope that is due to the cold conditions. Agree? Or, is there any adjustment that could be made? I watched your video and see how it works.

@PaulSikkema 3 жыл бұрын

Lock deicer or wd40 around the pivot point of the blue button should unfreeze it. Myself I have an infared brooder lamp that I just shine on frozen stuff like that. I also use it to melt the snow/ice out of the impeller when I'm done with the snowblower. Here's the bulb: amzn.to/3mNPgD6 and lamp fixture: amzn.to/34FEg4C

@xrpxtrariceplease2811 3 жыл бұрын

Hi Paul Is this the same setup for the toro powermax 824 OE? I went ahead and bought the toro over the ariens deluxe 24 and the comact24. I was lucky to get 10 %discount from the purchased price of $899(Home Depot) and I also bought the maintenance kit for $19.99 to get the one yr of extended warranty from toro for free.

@PaulSikkema 3 жыл бұрын

It will be similar. This video will help if the "picture book" setup guide is unclear

@xrpxtrariceplease2811 3 жыл бұрын

@@PaulSikkema I think your video is excellent guidelines to set up the unit

@alexanderraykhert1019 3 жыл бұрын

How’s the Ariens Professional 21’ been serving you? How many hours so far? Would love to see a follow up video.

@PaulSikkema 3 жыл бұрын

When it comes to sidewalks and cement where it's cracked the Pro 21 is the best single-stage on the market. The floating scraper never catches and it cleans down to the pavement very well. I have a lot more sidewalk now so you'll see me using it a lot more this year.

@alexanderraykhert1019 3 жыл бұрын

@@PaulSikkema Excellent to hear, how many hours do you have on it so far?

@PaulSikkema 3 жыл бұрын

I still have it packed away. When I get it out I'll check

@xJUSTxRESETx 3 жыл бұрын

Do they make a modification for the deflector on the chute so that it aims down at an angle rather than straight out to the side?

@PaulSikkema 3 жыл бұрын

Yes, the next model up gives you the better chute. Watch this video to see the difference. kzfaq.info/get/bejne/qKp6lct0tZfMl4U.html

@xJUSTxRESETx 3 жыл бұрын

What I am wondering is if I can buy a part to modify the 828 deflector so that it shoots down at an angle?

@PaulSikkema 3 жыл бұрын

No, The two chute bottoms are different so you'd have to buy a complete new chute assembly for the 928 to get the parts you want.

@xJUSTxRESETx 3 жыл бұрын

Okay thank you

@BartStar009 3 жыл бұрын

The 1st speed forward is too fast on my Toro Powermax 928 BUT when I adjust it the tiny little bit it goes in reverse, at the LOWEST setting on 1st gear forward it's very-very-VERY close to reverse, the lowest setting I can get it's still too fast, I have to walk too fast to keep up, I either slip the traction lever or lower the throttle setting to slow it down, but lowering the throttle also effects the auger less power to pickup and throw the snow, My Ariens Deluxe 30 goes much slower in 1st gear forward. It's Toro's failure on the design and size of the friction wheel matched with the size of the belt pulleys and the engine RPM, Toro needs to go back to the design board and make the traction slower and the auger faster. The Ariens is perfect and is better engineered. Please don't take it personal Paul cause I have the highest respect for you and enjoy all your video's.

@PaulSikkema 3 жыл бұрын

Please watch this video. The 928 is in first gear. Is that too fast? kzfaq.info/get/bejne/iMWgdLF6ndPamnU.html

@suprand Жыл бұрын

Hey Paul. Looking between this and the 30 inch with the 302cc motor. Do you think there’s a big enough difference in terms of real world power performance ? Thanks

@PaulSikkema Жыл бұрын

The 30 inch will have the same power-to-width ratio as this one. With Toro you don't get the "big power" ratio until you move up to the 1428 and 1432 commercial machines.

@suprand Жыл бұрын

@@PaulSikkema thanks. Now just have to decide between this and the comparable ariens deluxe 28 and 30. Getting rid of my 2017 husqvarna st224. Good engine and body. But flawed cable system that constantly break. Slightly underpowered in my opinion 208cc with a smaller auger and impeller compared to the ones im looking at.

@PaulSikkema Жыл бұрын

I understand your frustration with the Husqvarna. I've had four different models over the years and their biggest issue has always been the control cables. Ariens or Toro. That's really a tough choice. They are both the best snowblowers on the market today and you can't go wrong with either brand. So, here's a few things that may help you decide. 1. Go to both dealers and see which dealer you like best. Trusting the dealer goes a long way to being happy with your new snowblower. 2. Try out the controls. Watch my unboxing videos and I'll show you how to use the controls correctly. Some people like Toro's joystick and others like the simplicity of the Ariens crank. Move the snowblower around the sales floor to see how each one fits you. 3. Both handle heavy/wet snow and slush a LOT better than your ST224. Both will throw a LOT more snow than your ST224 and throw it a lot farther. To be very nit-picky - the Toro throws snow farther but the Ariens throws more snow. I can usually walk a little faster with the Ariens if I'm clearing 6-10 inches. 4. Both Toro and Ariens will last you many, many years.

@suprand Жыл бұрын

@@PaulSikkema great info. I appreciate the info!

@eugenerichardson8013 Жыл бұрын

Do you need to clean the snowblower after using it?

@PaulSikkema Жыл бұрын

When you are done clearing snow run the front auger for a few seconds to clear out any snow remaining in the housing. If the snow is really sticky and there is a lot left in the housing - turn the engine off - remove the safety key - and then tip the snowblower up, back on the handles. Use your cleanout tool to remove most of the snow. Instead of cleaning out the snowblower by hand I use an infrared heat lamp. I shine it into the housing for a few hours and it melts all the snow and drys it out. www.farmandfleet.com/products/676976-woods-farm-utility-brooder-lamp.html. www.farmandfleet.com/products/714269-feit-electric-250-watt-br40-red-heat-lamp.html

@jandksolutionsllc3663 3 жыл бұрын

Picked up pre assembled 828 from Home Depot. Has oil already. Started right up. Let it run a few minutes. Running fine. However, noticed a burning type smell. Assume it is just burning off factory stuff. Is this correct? If so, how long until this burns off? Or, something else? Please advise. Thanks.

@PaulSikkema 3 жыл бұрын

The paint on the muffler will burn off on the first 30 minutes of run time. That's what you smell.

@jandksolutionsllc3663 3 жыл бұрын

@@PaulSikkema thank you for quick response! Do they normally come with oil in it? It’s so clean, barely visible, buts it’s there.

@PaulSikkema 3 жыл бұрын

Yes, 2-stage snowblowers come in a crate and the oil is already in the engine. THD should have taken it out of the crate and assembled it correctly - but if anything doesn't seem right watch this video.

@AStanton1966 3 жыл бұрын

I have a newer Mustang and I still get a funky smell when I open it up to do an Italian tune-up.

@deaconpladek Жыл бұрын

still shopping... What does company recommend for gas? ethanol or non? high test or regular? Does this require chains on tires for heavy snow storm or is it heavy enough? What is correct tire pressure?

@PaulSikkema Жыл бұрын

All new engines are rated for 87 octane E10 fuel. DO NOT USE E15 FUEL! Todays snowblowers all use a high traction snow tire so you don't need chains. This snowblower has all the weight balanced over the wheels so it has plenty of traction. The correct tire pressure is listed in your operator's manual. The manual either comes in a plastic bag hanging on the new machines or Toro specifically has a QR code on the nameplate at the back of the transmission. Scan that code with your phone and it gives you a link to the manual.

@deaconpladek Жыл бұрын

@@PaulSikkema thanks; that helps me a lot.

@madmmx18976 3 жыл бұрын

Can you add heated hand grips to the toro 828 HD? There is a cutout on the control that looks like it is for one but I have read that you can’t add it to these models

@PaulSikkema 3 жыл бұрын

the reason there is a cutout is one dash goes on many different models. Toro does not offer a kit to add handwarmers.

@madmmx18976 3 жыл бұрын

Is there any reason I couldn’t add aftermarket hand warmers?

@PaulSikkema 3 жыл бұрын

Tes, you will have to check with your dealer to see if the alternator on your model can handle the extra current. Most snowblower engines that only have lights have small alternators. They are not capable of handling the extra current load of handwarmers.

@madmmx18976 3 жыл бұрын

@@PaulSikkema Thanks. I will look into it.

@spudman9367 2 жыл бұрын

@@madmmx18976 the have the Red Heated Grip Kit, part # 144-1603 however it is not in stock at this time. If you look at the parts manual for the 826 which has the heated grips you can order the parts individually. That is what I did. The Alternator on the 828 and 826 is the same and can handle the light and heated grips. Just installed them on my 828

@eastonatkinson8071 3 жыл бұрын

What is the red plastic piece to the right of the primer bulb?

@PaulSikkema 3 жыл бұрын

That is the safety key. Pull that to stop the engine - remove it to keep others from using the snow blower.

@eastonatkinson8071 3 жыл бұрын

Thank you!

@davidwester9761 3 жыл бұрын

Paul, I am in the market for a new blower and your articles and videos are a huge help, thank you! Should I be concerned about Toro and others being made in China? with the Corona virus supply chain disruptions and the trade hostilities between the US and China I wonder about parts availablility going forward? I know you recommed Toro but is it safer to get a US made machine like Troy Bilt?

@PaulSikkema 3 жыл бұрын

Toro is made in Bloomington, MN. Ariens is made in Brillion, Wisconsin. Troy-Bilt, Cub Cadet, Craftsman are made in Ohio. The confusion may be that ALL snowblower engines are made overseas - most of them in China. These engines are generally shipped months in advance so there is no shortages at this time. We did have an issue with engine last summer (2019) because the Port of Los Angeles got behind but that was quickly fixed by rerouting the container ships to other ports of entry - like New Orleans.

@davidwester9761 3 жыл бұрын

Thank you Paul, that helps. I live in Massachusetts and have a very large driveway (165’ long, plus a circle and parking area) totaling 7,200 sq. Ft. What blower would you recommend. My 18 yr. old Ariens 824 still runs but I want something bigger and better to handle the heavy wet snow and get the job done faster. What do you recommend?

@PaulSikkema 3 жыл бұрын

If you want to stick with Ariens I highly recommend the Deluxe 30 or Deluxe 30 EFI. You'll get done a lot faster and can clear the long part in just two round trips. If you get a lot of snow consider the Platinum 30. It will clear 15 inches or more as fast as you can walk.

@davidwester9761 3 жыл бұрын

@@PaulSikkema I am actually leaning towards the Toro now. Would you recommend the 928 OAE or the 1030 OHAE for my situation? Toro is saying no shear pins needed, plus with the current promo Toro is cheaper. Are shear pins much easier to change now on the Ariens? My 18 yr. old Ariens requires a nail punch to get broken pin out.

@PaulSikkema 3 жыл бұрын

I've been reviewing Ariens for over 10 years and I've only once broken a shear pin. And that was because I stuck the snowblower in a chain-link fence...That one fell out. I'd go with the 1030. It's a little wider so it will get the job done just a little faster, it has the same power to width ratio as the 928, and it has heated handgrips!

@tele-j5325 Жыл бұрын

Hi Paul~ Great video, very thorough run through. I've used this machine about 6 times so far since purchase (December 2022) and have been impressed with the performance. However, yesterday after taking a break, upon restarting the engine, all of a sudden I only had one reverse speed. The slower reverse speed had changed to a very slow forward speed. Also, the speed selector lever won't move into the highest speed slot. Any ideas?

@PaulSikkema Жыл бұрын

Something broke in the shift linkage or inside the transmission case. I suggest getting it back to the dealer and let them look at it.

@bombidude 5 ай бұрын

Paul I never tried a Toro before.. I used all other brands lol.. But this blower looks good.. HD has it for 1599.. I'm thinking about making a purchase... I owned ariens before what's your opinion on this Toro?

@PaulSikkema 5 ай бұрын

The Ariens Deluxe 28 is the snowblower everyone is trying to beat. Check out this video were I compare this Toro Power Max HD 828 to it. kzfaq.info/get/bejne/gd6IqLGLvKqwiZs.html

@tiredoldman5329 5 ай бұрын

Is there supposed to be a braking system on this thing? I let go of the handles turned around and the thing rolled away down my driveway.

@PaulSikkema 5 ай бұрын

Snowblowers don't have brakes on the wheels. If you are on a slope that steep turn the snowblower sideways before you let go...

@tiredoldman5329 5 ай бұрын

@PaulSikkema I know they don't have breaks on the wheels. But the transmission should. Let go of the handles, it shouldn't roll away.

@PaulSikkema 5 ай бұрын

I've never thought about having a brake on the tranny. Probably because if the slope is steep enough that it would slide that the slope is too steep to walk on. That said, I'll mention it to the snowblower engineers next time I see them. Snowblowers with hydrostatic transmissions or tracks don't need the brake. The only brake they have is on the impeller/auger so it stops right away - for safety.