Toyota 4Runner • DIY Front Brakes • Learn in less then 10 minutes

Рет қаралды 4,859

2 жыл бұрын

#diy #4runner #brakejob #frontbrakes
Learn how to change the front brakes on your Toyota 4Runner in less then 10 minutes.
Parts replaced :
Brake rotors/discs(x2) br900910-02
Brake pads 04465-35290
Shim kit 04945-0c030
Brake pad holding pins(x4) 47735-60300
Check out some of my must haves, on my Amazon store:
www.amazon.com/shop/vikingsga...
Thank you for watching and share it,
if you found it to be helpful.

Пікірлер: 37

@trailrunnah8886 Жыл бұрын

This is a great tutorial. I'm in the process of doing this job on mine right now, I have everything apart, and let me tell you that 17 mm swivel would have been really useful! I had fun breaking those free with a breaker bar lol. I realized I need to replace the calipers, Pistons in the driver side are seized, and I cannot get the pins out of the passenger side, so my job's a little bit more complicated. At least I'll have no issues getting the pads back correctly.

@VikingsGarage Жыл бұрын

You got this, always a fun time with those front brakes.

@lostagain2992 10 ай бұрын

Not as thorough as your others but good just the same. Can you show how to bleed the brake lines without the Toyota apparatus?

@silverrunner8687 2 жыл бұрын

👍🏻

@jeremychrist Жыл бұрын

Great Video! For the rear brakes, what grease do you use for the rear brake slide pins? Also, what are your recommendations for breaking in new pads with new rotors?

@VikingsGarage Жыл бұрын

Thank you! You can use the little grease pack that comes with the brake pads. Breaking them in is nothing to crazy, just drive normal without sudden stopping for the first 100 miles. 👍🏻

@rhino4602 5 ай бұрын

Great video, what size bolt did you use to remove the rotor?

@VikingsGarage 5 ай бұрын

It’s your standard 12mm bolt. 💪🏻

@smokinwithskruggs Ай бұрын

Didnt realize you are a Toyota Tech. My wife is super hard on brakes with rotor warpage. Any suggestions on aftermarket HD rotors?

@VikingsGarage Ай бұрын

I would stick with OEM rotors, but if in a budget STOP TECH makes good stuff also.

@smokinwithskruggs Ай бұрын

@@VikingsGarage appreciate the info!

@GG-un5wk 2 ай бұрын

Thx man for another great explanation. Do you know if is ok to clean the brakes ( with brake cleaner obviously) every 5k when I’m doing tire rotation? Thx for your help

@VikingsGarage 2 ай бұрын

There should be no need for you to clean your brakes with brake cleaner every 5k. The only time you use brake cleaner is when you’re doing a brake job.

@GG-un5wk 2 ай бұрын

Thank you!

@jasoncarr5595 Ай бұрын

Good video. What size is the bolt u used to back off the rotor? Thanks

@VikingsGarage Ай бұрын

13 mm

@jessevankoughnett5111 Жыл бұрын

Being a Toyota tech/5th gen 4Runner owner have to experienced constant “warped” rotors, I recently had the trd pro in for service for “back slap” and the tech added a upper anti rattle clip used oem blue backed pads and shims this being said I believe during his test drive post install the rotors were hot spotted warped (aftermarket) less then 1200km this is the second set or f warped rotors I’ve experienced any input would be appreciated thanks have a good day.

@VikingsGarage Жыл бұрын

One it could be the quality of the rotors, you need to get OEM or Stop tech rotors. Two it could possibly be improperly brake in , first 1000 miles . Absolutely, positively no hard stopping at all.

@jessevankoughnett5111 Жыл бұрын

Ok thanks a lot for your input depending on OEM pricing I might try the stop techs, got vehicle 6 months ago haven’t even put5500km on it and been plagued by front brake issues/noise the dealership put garbage brakes on as a part of the deal. Now I’ve since payed them to changed the pads as explained earlier, I was hopeful the rotors would be ok I should have learned my lesson with the first set they threw on and assumed they used the same… should have ditch the “warranty” and taken care of everything myself 🤦

@VikingsGarage Жыл бұрын

👍🏻👏🏻👏🏻

@johnshipps441 Жыл бұрын

What do you recommend for those of us with 4th Gens and the seizing calipers? I’ve already replaced them once and they’re seized again. Some people swap them out for 5th Gen calipers, some say steel brake lines are the answer. Do you have any experience with this and know of a solution that works?

@VikingsGarage Жыл бұрын

Honestly. At the end of the day they all ended up seizing. It’s just something you have to live with. No solution

@johnshipps441 Жыл бұрын

@@VikingsGarage 😩😩😩

@morfdq 10 ай бұрын

Live by your videos. Quick question. We are hearing like a groan when letting off the brake pedal. Any thoughts on that? It’s a 2022 40k miles. Appreciate you!

@VikingsGarage 10 ай бұрын

I really appreciate your support!! And I really want to help, but it would be really hard for me to diagnose this based on your description. I don’t want to be guessing… best advice I can give you is. Check your brakes first, at 40k you might need front brakes, that’s usually more or less how long they last. Best of luck!! Let me know what you find

@morfdq 10 ай бұрын

@@VikingsGaragethank you. Yeah doing both front and rear tomorrow with OEM pads and rotors. Going to do them exactly how you showed in the video

@VikingsGarage 10 ай бұрын

@morfdq OEM That’s the way to go!! You got this!! 👏🏻💪🏻

@morfdq 10 ай бұрын

@@VikingsGarage. Yeah brother. Done and done. Groan is gone. I didn’t realize the OEM pads didn’t come with hardware. I was able to clean the pins really good. Thank you again

@VikingsGarage 10 ай бұрын

@morfdq 👏🏻👏🏻👏🏻