Toyota Lexus TUNDRA & SEQUOIA 4.7L Valve Cover Gasket Replacement | 2UZ-FE | 1ST GEN

Toyota Lexus TUNDRA & SEQUOIA 4.7L Valve Cover Gasket Replacement | 2UZ-FE | 1ST GEN | Land Cruiser

Рет қаралды 21,209

Жыл бұрын

Replace valve cover gaskets Tundra Sequoia 4.7L 2UZ-FE. 2001 2002 2003 2004 2005 2006 2007. Also replace the oil tube seals. Do the spark plugs if they have not been done is a long time.
‪@toyotausa‬ ‪@toyotasequoia9231‬
LINKS TO ALL THAT IS GOOD
Fel Pro Valve Cover Set: amzn.to/3ELIFWr
90 Degree Pliers for clips: amzn.to/3yL9Ay0
Propane Torch: amzn.to/3eBQTpu
Milwaukee 3/8ths Electric: amzn.to/3T8Mzgu
TUNDRA / SEQUOIA ALTERNATOR: • Tundra Sequoia [EASY] ...
SEQUOIA OVERVIEW: • New Bundymobile | Toyo...
TUNDRA / SEQUOIA FRONT 12V OUTLET INOP: • Toyota Sequoia Passeng...
4.7L TUNDRA SEQUOIA THERMOSTAT: • 01 - 07 Toyota [EASY] ...
BUNDY APPROVED TOOLS AND CHEMICALS:
BEST Dielectric Paste: amzn.to/3KJL053
BEST KIMO 3/8ths Electric Ratchet: amzn.to/3o51OK0
BEST RTV IN THE WORLD (FIPG): amzn.to/3s09hLB
BEST Anti-Seize for Spark Plugs: amzn.to/3KNE9Y9
BEST Mechanic Work gloves: amzn.to/3KTBBYv
BEST Zero Offset Wrenches Metric: amzn.to/3KTAIzs
BEST Metric Wrench SET: amzn.to/3u2NHIZ
BEST Underhood Work Light: amzn.to/3u4EOOW
BEST Headlight Restoration Polish: amzn.to/35w94YY
BEST Synthetic Motor Oil: amzn.to/3u3uM0E
BEST Headlamp Work Light: amzn.to/32ISTqe
BEST Grease for Wheel Bearings: amzn.to/3rQ1ik8
BEST ½inch Electric Impact: amzn.to/3IMa89c
More About BundysGarage:
goo.gl/qv3Wzc
Questions, Comments, Concerns:
bundysgarage@gmail.com
Twitter:
/ bundysgarage
@bundysgarage
On The Web:
www.bundysgarage.com
Music by Randall Kent: As seen on NCIS
• Randall Kent - Going H...
All Rights Reserved 2022
© Copyright 2022
Bundys Garage
All rights reserved. This material may not be published, broadcast, rewritten or redistributed in whole or part with out the express written permission. Contact: bundysgarage@gmail.com
DISCLAIMER - DISCLAIMER - DISCLAIMER
Due to factors beyond the control of BundysGarage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. BundysGarage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. BundysGarage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of BundysGarage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not BundysGarage nor any of it’s subsidiaries.

Пікірлер: 26

@erikalbertson2024 2 ай бұрын

Great video - thank you! Skip the torch and hold the bolt washers in a pair of pliers and use a drill driver w/ a 10mm socket to spin them off. New ones press on by hand.

@jameswiththegermanshepherd6628 Жыл бұрын

Excellent instructions. I was perplexed on the tube seals. Thank you.

@ickycarp7232 Жыл бұрын

Great video, im doing this project today after work.

@lilokyang6280 Жыл бұрын

Love watching your videos! 👍👍👍

@aclawrence 3 ай бұрын

Great job on this video!

@bundysgarage 3 ай бұрын

Thank you

@hoists1829 Жыл бұрын

nice video👍👍👍

@paradigmshift9772 5 ай бұрын

To remove the grommet off the valve cover screws you can take some channel locks and hold it by the grommet then take your number 10 mm with a drill And it comes right off.

@bradgman5851 Ай бұрын

Thank you!

@scottshipley7376 6 ай бұрын

Good video 👍

@TheSwiftie Жыл бұрын

Great video! I watched one with WAY too much information. Almost was not going to do it myself. You changed my mind. 2 thumbs up!

@jakevolk9837 Жыл бұрын

Totally agree! Looks easy enough.

@serchizm Жыл бұрын

I got quoted by a local “brand name” tire shop $210 for the valve gasket kit, and $400 for labor. Wanting to do this job myself, but I’m not very mechanically inclined. How hard was it?

@bobbouchee1452 Жыл бұрын

idk about srapying brake cleaning inside my enchine that shits gunna eat your bearings right up in no time smh you went overboard just soak the oil up spray some on a rag and wipe it down

@jsgrauman Жыл бұрын

Is the hose connector on top of the passenger valve cover a press fit or threaded, does it need to be replaced like the pcv?

@mtnsick44 7 ай бұрын

Why do you have to remove those little rubber grommets? Can't you reuse them to bolt down the valve cover?

@erikalbertson2024 2 ай бұрын

no - gasket kits come with new ones

@kevinthompson776 Жыл бұрын

The spark plug tube seals were installed backwards. The side with the gap in the seal goes on inside of the the valve cover. Good job otherwise!

@bryin99 11 ай бұрын

Incorrect

@BoneStack117 10 ай бұрын

Wrong, they are installed correctly per his instructions

@bryin99 10 ай бұрын

Hey buddy I already addressed this.

@revisionindustries667 9 ай бұрын

No the side that’s raised goes towards the hood of the vehicle . He installed incorrectly

@Rhythm_R_Us 2 ай бұрын

As someone who's done tube seals, I thought the exact same thing, but maybe do a Google search before stating something like that. First diy forum had the tube seals in this orientation.