Transom Reinforcement Deltaforce Vortex 24 Build Series

Transom Reinforcement Deltaforce Vortex 24 Build Series - Twin Motor Hydroplane

Рет қаралды 959

Күн бұрын

DELTAFORCE VORTEX HULLS
www.offshoreelectrics.com/pro...
LEOPARD 2850 X2
www.offshoreelectrics.com/pro...
4mm strut
www.ebay.com/itm/186037496359...
4mm flex cable
www.ebay.com/itm/395043581981...
TURN FIN IS FROM AQUA CRAFT UL-1
4mm to 4mm COUPLER
www.offshoreelectrics.com/pro...
6mm LARGE SILICONE TUBE
www.offshoreelectrics.com/pro...
SMALL WATER OUTLET
www.offshoreelectrics.com/pro...
70mm RUDDER
www.offshoreelectrics.com/pro...
OSE SERVOS
www.offshoreelectrics.com/pro...
VENOM CARBON KIT 12"X60" 12oz RESIN
www.ebay.com/itm/115173374556...
HATCH LOCK SMALL
www.offshoreelectrics.com/pro...
CARBON FIBER SHEET
www.offshoreelectrics.com/pro...
SADDLE TAPE 0.5" 12.5m WIDE
www.offshoreelectrics.com/pro...
OSE CONNECTORS & BULLETS www.offshoreelectrics.com/pro...
K&S BRASS TUBE
www.offshoreelectrics.com/pro...
FE RC BOAT COUPLER & COLLETS
www.offshoreelectrics.com/pro...
4016 prop
www.offshoreelectrics.com/pro...
4016 reverse prop
www.offshoreelectrics.com/pro...
3619 prop 4mm
www.offshoreelectrics.com/pro...
Thanks for Watching Ironclad Rc Tinker test and tune everything.
Personal contact information ironcladedout@gmail.comFacebook
share/eknUp8...
TikTok
www.tiktok.com/@ironcladrc?_t...
Instagram
ironcladedo...

Пікірлер: 26

@minochercowasjee 15 күн бұрын

Big B, this is really helpful . What you don’t mention is that you are extremely skilled with years of practice !! It takes skill to do what you do . Very appreciative of you sharing how to do things with detailed explainations .

@IRONCLADRC 15 күн бұрын

This process looks hard but it's actually very simple once you understand the process. Good luck my fried

@waynesbutler7834 15 күн бұрын

Your channel provides a valuable service that no one does as well as you . Thats alot of aluminum hanging off the back of this Hydro . SMC batteries considering they are often the heaviest will be a good counter balance for good CG but you already have this under control , can hardly wait till it hits the water .

@8fordhamsRC_adventures 15 күн бұрын

Another great video, tons of good information here. Can't wait to see this thing rip man !

@h2omechanic 15 күн бұрын

I don't think so! 😂 I'm guilty of using kitchen rags too!

@paintendaveextremecollisio8057 15 күн бұрын

Great Video 👍

@Scramblerkidd 15 күн бұрын

You can also use modeling clay in the drilled holes to preserve the holes before the layup

@IRONCLADRC 15 күн бұрын

Oh yeah that would have worked perfectly. Thanks for the tip

@artpeck9272 15 күн бұрын

B - those are called “pinking shears”. They minimize the unraveling of fabric. Not sure how well it will work in carbon fiber. My sister used a pair for her dress making.

@nealstarling5422 15 күн бұрын

Sweeeet, thanks for showing us the details 👍 Wish I had reinforced my shrimp rigger motor mount, things turned out kinda catastrophic, don’t know what I was thinking. I used thin burch plywood on the transoms of the BJ24 V1 Again thanks for showing us the details Big B BGFL

@IRONCLADRC 15 күн бұрын

No problem 👍

@holgerlafrenz2895 15 күн бұрын

Good tips, B, especially about the wash cloth 😂. Just kidding. The amount of epoxy to cloth ratio 👍. I always mix too much.

@IRONCLADRC 15 күн бұрын

Thank you. I'm glad I can help!

@artpeck9272 15 күн бұрын

You either have really big balls or a very comfortable sofa! 😂 I’m considering major surgery on my Motley Crew. I think I’ll cut out the tub, pull out the stuffing tube and reinforce the bottom with carbon fiber. The hull is fiberglass, but if I take Bill O’s suggestion on motor/esc/prop, I’m concerned about strength. Videos are very helpful.

@IRONCLADRC 15 күн бұрын

I say go for it! That tub should have never been in that boat. Good luck

@artpeck9272 15 күн бұрын

@@IRONCLADRC yeah, it just in the way.