Just finished installing the Tidy. Thank you for your video it made it much easier. That being said…four hours later…done. I needed to take screenshots as the wiring was challenging. The stock wires required my looking closely at your work to figure out what goes to what. Thank you again.

Looks so much better with this. Thanks for the video!

Brilliant ! I've just received mine and yet to fit it. Thanks for an ever so helpful video :)

I fitted mine 2 weeks ago and there were a few snags for me- firstly cutting the cable tie for the loom under the swinging arm which you haven't shown and was really awkward; secondly as a tech I assumed the 3 wires would be colour coded to the lamp but for reasons best known to Evotech they aren't 🙃; lastly the 2 chrome bolts you reused on the seat panel are identified wrongly in the instructions as being 2 in the fixing kit which are too big. Other than that, very pleased with the result as I've never liked those tyre hugger contraptions. Greetings from the UK.

Great video just used it to install mine. Thanks you

Great vid, fitted mine yesterday and the vid was a great help 👍🏻

Normally, not something I get worked up over, but this change looks really nice without replacing the turn signals for invisible dots. And given they work so well with the bags, takes it from cutesy to road worthy. Well done!

Thanks for the video, just recently installed mine and made this a reference.

Excellent video, thanks

So much better good job

Needed more detail for the wire that runs along the swingarm but other than that this was an effective enough how-to. Thanks!

Just the video i was looking for showing the dismantling, including wiring, of the number plate and rear light mount. Great - useful to know how to swap indicators. You should perhaps amend the title to include "instillation" as there's loads of vids showing accessories but few with the detailed dismantling and assembly shown in yours.

A lot better look than those awful floating fenders, good video.

Good professionally done video. I would have liked to have seen the end result for a little longer and without the bags and awful music (I suppose you can’t please everyone lol😂) Well done!🙋‍♀️🏍💖

What part is that at 7:11? That light didn't come off my Trident, and my Tail Tidy didn't have those other two parts either.

on minute 6:2à the bolt???? do not remove ok but we do not see again??? can you please explane regards

I may have missed it but the video doesn't seem to show you tightening the bolt not to be removed at 6:22, may catch somebody out following it and forgetting to tighten it back up after pulling the cable through.

Love it....

Thanks for making this vid. It was very helpful as a reference while I installed my TT. Removing the zip tie on inside of swingarm was not fun at all. Removing it was a small victory in and of itself.

good info, but wondering about the nut you are loosening at 6:25. it says to loosen it but not to take it off. Why are you loosening it at all? I don't see a wire behind it, is that just to free the wires?

Do you have a list of tools required? Tough to tell if there are torx bits involved somewhere in there. Great video!

Looks nice! Im considering one for my bike, but i wonder if this makes the bike "unridable" in rain, with water squirting all over my back because there is less cover in the rear?

Just a quick question what’s the brand for the short support of the license plate?

Hello, is it possible to install the original Trident 660 bracket on the Tiger Sport 660 motorcycle?

What’s the size of the axle nut? Also, what’s the proper torque to tighten the nut?

Will this fit the scrolling led indicators?

What are the side bags at 11:25 ? Thank you

Good except I found another zip tie right under the exhaust. Shifty spot.

More or less, how much time does it take the installation? Thanks

What are those side bags? Are those the ones from the Tiger? How did you fit them?

How much torque for the axle nut?

I did not understand the whole video, I would love it if they recorded this video with step by step for people not experienced in the subject, since there are shots that, due to the position of the person who makes the modifications, do not allow a good view of the process as it should be.

Bruh...Those blinkers can be seen from pluto! 😂😂

Can you fit it to daytona 660?

Having to undo the axle nut for something like this is exactly what's wrong with some engineers thinking.

What's everyone's thoughts on this? I'm still undecided.

I just wish they could use the original rear light and the new one didn't protrude as much, maybe some other companies may make some.

Not to my taste. Why can’t bikes have proper rear fenders?

in this instance a badly named product should be tail untidy.

Thanks to the ludicrous regulations for those planet-sized winkers

Damn that music is annoying

ohh lord the turn signals in the us are terrible!

This bike has got a unique design that stands out from the others, if you don't like it why buy it in the first place?

Kind of looked better the original way.

The stock one is better than this, looks llike garbage for me