Always happy to keep stuff working as long as possible.
Пікірлер: 28
@paulvekony32932 жыл бұрын
Can you show us the connection on the back with the reverse light?
@paulvekony32932 жыл бұрын
Hello mate Just a quick one To change the main unit, is it straight forward? Do you need to run again the cables or you can just unplug all the sensors and connect them to the new unit?
@UltimateDIY2 жыл бұрын
Hello! Depends a lot on who installed it and where. In theory it should be quite easy, as everything has connectors, so it's just plug and play when replacing with the same model.
@snov1533 жыл бұрын
Hi, I have a same problem. The display was working properly aprox. 2 months and now the numbers and the graphic is bad. Do you have the link of display where you bought replacement? I tried to buy replecement on the net and aliexpres but haven't find it.
@UltimateDIY3 жыл бұрын
Hi. No link, as I bought it from my country. Try to directly contact the manufacturer.
@snov1533 жыл бұрын
@@UltimateDIY ok, thanx
@thanyamariec73862 жыл бұрын
Hi may i ask what’s that button/switch on top of it for?
@UltimateDIY2 жыл бұрын
Hi. Either lower the volume or fully mute it. I don't exactly remember.
@suhailasaba1051 Жыл бұрын
4:29 Does the display have a voltage when the car is turned off ? I need to cut the display cable and take the display outside inorder to check it and see if I can repair it ? I wonder if I should disconnect the car battery or not in order to cut the display cable ? Thanks for the video.
@UltimateDIY Жыл бұрын
I don't think it has a voltage. Usually the sensors get the power from the reverse bulb. So they only have power while reversing. But don't know if this applies to absolutely all models.
@suhailasaba1051 Жыл бұрын
@@UltimateDIY Thank you for your answer.
@UltimateDIY Жыл бұрын
Welcome!
@BTunaTTV_YT Жыл бұрын
@@UltimateDIY is it normal for mine (made by Dunlop) to not show anything on screen when i put in reverse? I recently bought them and after installing it the screen doesn't turn on.... can it be because i connected the sensor black wire (ground/negative) to the negative of the light bulb)
@UltimateDIY Жыл бұрын
Really hard for me to guess, as I have no idea how your model looks like or it's suposed to be wired.
@ayaanmuzii78693 жыл бұрын
My sensor is billing on and off after one mintue then it is not working what will be problem
@UltimateDIY3 жыл бұрын
I do not know.
@jmiah754 жыл бұрын
Hi I have this sensor I have a problem. It makes a beep when I turn it on. And says e0 and then turns off
@jmiah754 жыл бұрын
It stays on for about 2 3 seconds and turns off I don't know what I did wrong when I installed it
@UltimateDIY4 жыл бұрын
Is it a new install? Did it ever work correctly or directly with this error?
@jmiah754 жыл бұрын
It's a new install
@jmiah754 жыл бұрын
I don't understand what I've done wrong I have a 07 astra h
@jmiah754 жыл бұрын
I connected and wound the wires together black to brown wire andd the red to the white reverses white . Used a wire cutter to expose the sheath
@UltimateDIY4 жыл бұрын
▬▬▬▬▬▬▬▬▬ஜ۩۞۩ஜ▬▬▬▬▬▬▬▬▬ T H A N K Y O U F O R W A T C H I N G ! P L E A S E L I K E A N D S U B S C R I B E !▬▬▬▬▬▬▬▬▬ஜ۩۞۩ஜ▬▬▬▬▬▬▬▬▬