How to Replace Front Wheel Bearing 2012-2020 Ford Focus

Рет қаралды 79,682

2 жыл бұрын

Buy Now!
New Wheel Bearing from 1AAuto.com 1aau.to/ib/1ASHF00494
Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision. This video shows you how to install a new wheel hub and bearing on your 2012-2020 Ford Focus.
This process should be similar on the following vehicles:
2012 Ford Focus
2013 Ford Focus
2014 Ford Focus
2015 Ford Focus
2016 Ford Focus
2017 Ford Focus
2018 Ford Focus
Tools you will need:
• Flat Blade Screwdriver 1aau.to/opq/1AXAA00013
• Pry Bar 1aau.to/oeb/1AXAA00020
• 10mm Socket 1aau.to/omW/1AXAA00017
• 15mm Socket 1aau.to/opt/1AXAA00015
• 18mm Socket 1aau.to/ogC/1AXAA00043
• 19mm Socket 1aau.to/ogC/1AXAA00043
• 30mm Socket
• 32mm Socket 1aau.to/ox/1AAST00003
• Brake Caliper Hanger 1aau.to/o7/1AXAA00084
• Press
• Bent Nose Pliers
• Metal Cutters
• Pliers
• Snap Ring Pliers
• 3/8 Inch Air Impact Gun
• T25 Socket 1aau.to/ocP/1AXAA00008
• T55 Torx Socket
• 3/8 Inch Breaker Bar
• Ratchet 1aau.to/oqG/1AXAA00016
• Torque Wrench 1aau.to/oi5/1AXAA00044
• Anti-Seize Grease
• Rust Penetrant
• Center Punch 1aau.to/oaC/1AXAA00055
• Chisel 1aau.to/oaC/1AXAA00055
• Hammer 1aau.to/od9/1AXAA00091
Subscribe: / @trq
Check out our playlist:
Ford Focus 2012-2020 3rd Generation: • Ford Focus 2012-2020 3...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 35

@TRQ 2 жыл бұрын

√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money

@ifixthings86 Жыл бұрын

There's a much easier way to remove the spindle from the strut. Put a putty knife in the cutaway where the bolt came out. Put the bolt in threaded side and tighten the bolt to the putty knife, this will push the cutaway apart, and the spindle will just fall off.

@ZaSim3717 11 ай бұрын

Thanks so much! Your videos have saved me thousands of dollars for something I could totally do myself! I ended up replacing the whole knuckle assembly as it was only $30 more than just the bearings!

@HeavyMetals1969 Жыл бұрын

Though every repair has its own issues this vid saved me hundreds. I also replaced the lower control arm/ball joint (They are not separate on the Focus 2012) Much thanks. I will repair anything I can, and "the man" can pound sand.

@perjian1697 Жыл бұрын

Why did you fight the retainer ring out with a hammer and chisel?! LoL. All you had to do was put the snap ring pliers back on it and rotate your wrist and walk it out. 😆

@josefranciscoesquertalaman3827 2 жыл бұрын

Presente cordial saludo desde Navoyork Sonora México

@davidburt7517 Жыл бұрын

ANOTHER GREAT VIDEO, THANKS

@Daisy30y03 5 ай бұрын

Amazing video, bro. Tysm

@javiersandoval1291 11 ай бұрын

excellent and clean job....thanks

@Burnichok 3 ай бұрын

Great video, thanks a lot! Very clear

@REVNUMANEWBERN 5 ай бұрын

19:56 Just a thought on installing the knuckle on the strut, if you can drive a chisel or something into that knuckle slot where the bolt goes in to spread the slot out some I believe it would go on the strut easier

@streetpunk99 Жыл бұрын

Do you know of any reason why after this job the wheel speed sensor would be throwing traction and abs codes as well ashill assist. It worked prior to the bearing change and the sensor has been replaced and cleared with a scan tool. All the codes immediately return as soon as you start driving.

@pstapsta2549 Жыл бұрын

Is it necessary to replace the Seal / Dust Shield? I didn't notice that step on reassembly, seems like it should also be replaced.

@wooddawg4868 8 ай бұрын

It' 's good to have a bearing pusher but most of the time folks just buy the entire knuckle with the bearing already in from the factory because the cost is not that much.

@larrygarza9334 Жыл бұрын

thank you so much

@brutusjb3814 2 жыл бұрын

I like how you didn't mention that the bearing has a magnetic ring for the ABS sensor and it can be put in backwards I followed your tutorial, but put the bearing in backwards only learning It was possible from another video.

@TheOmaJohn 2 жыл бұрын

I'm not sure if you're strange for liking that you put something back together incorrectly because it wasn't covered, or if you're strange for using sarcasm on a video that shares a ton of information and was obviously made pretty carefully and with knowledge. But hey, I like how you provided a bit of information that was missed in the original video. That's helpful.

@brutusjb3814 Жыл бұрын

@@TheOmaJohn sure the video is informative, but only to the point that it is possible to ruin a component you are installing.

@lts30000 Жыл бұрын

@@brutusjb3814 thanks for helping everyone else out. Nice work pal.

@jessefincham8899 Жыл бұрын

🤣 😂I’m done.

@1TPR4LIFE1 Жыл бұрын

Lol you shouldn’t be doing repairs if you didn’t know about the abs ring

@NG-tz8wo 10 ай бұрын

I just bought a knuckle with the bearing online. A lot easier and quicker.

@fredwilliams420 Жыл бұрын

Why not use the other bearing to start with?

@aaronreash814 Жыл бұрын

Pretty sure you just saved me close to $300 in one video, shop called said i need a bearing and a battery, i asked is it bad they said some play, i said it can wait, just gotta talk my friend into doing the knuckle for me and see how much that will cost me.