How to Replace Rear Brakes 2017-Present Ford F-350 Dually

Рет қаралды 242,788

4 жыл бұрын

Shop for New Auto Parts at 1AAuto.com 1aau.to/c/387/bq/brake-kits
Brake pads wear out over time, much like tires, and need replacing, on average, every 50,000 miles, with variations depending on driving habits and environment. Brake rotors may also need to be replaced if they are warped or grooved. Often, it’s safer and more cost effective to replace pads and rotors at the same time. Squealing or grinding noises, or wheel vibration are all symptoms of worn brakes. This video shows you how to install new, quality TRQ brake pads and rotors on your 2017 and up Ford F-350 Super Duty.
• Check here for more videos on the 2017+ Ford F-350: • Ford F-350 2017-2020+ ...
This process should be similar on the following vehicles:
2017 Ford F-350 Super Duty
2018 Ford F-350 Super Duty
2019 Ford F-350 Super Duty
2020 Ford F-350 Super Duty
2021 Ford F-350 Super Duty
2022 Ford F-350 Super Duty
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXAA00013
• Pry Bar 1aau.to/oa/1AXAA00020
• 16mm Wrench
• 18mm Socket 1aau.to/oa/1AXAA00043
• 21mm Socket 1aau.to/oa/1AXAA00043
• 24mm Socket
• Brake Caliper Compressor Tool. Dual Piston. Pump Style. 1aau.to/oa/1AXAA00289
• 3/8 Inch Air Impact Gun
• 1-1/8 Inch Socket
• E18 Inverted Torx Socket
• 1/2 Inch Breaker Bar 1aau.to/oa/1AXAA00078
• 1/2 Inch Ratchet 1aau.to/oa/1AXAA00043
• 3/8 Inch Drive Ratchet 1aau.to/oa/1AXAA00015
• Ratchet 1aau.to/oa/1AXAA00016
• Swivel
• Torque Wrench 1aau.to/oa/1AXAA00044
• Block of Wood
• Brake Fluid
• Brake Grease
• Brake Parts Cleaner
• Cloth Rags 1aau.to/oa/1AXSS00035
• Gear Oil
• Gloves 1aau.to/oa/1AXSS00048
• Liquid Thread Locker
• Rust Penetrant
• sanding disc
• Assistant
• Center Punch 1aau.to/oa/1AXAA00055
• Drain Pan 1aau.to/oa/1AXAA00320
• Hammer 1aau.to/oa/1AXAA00091
• Jack Stands 1aau.to/oa/1AXAA00065
• Razor Blade / Gasket Scraper 1aau.to/oa/1AXAA00280
• Vise
• Wire Brush 1aau.to/oa/1AXAA00079
Subscribe: / @trq
Check out our playlist:
Ford F-350 2017-2020+ 4th Gen: • Ford F-350 2017-2020+ ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 126

@TRQ 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@texnokrat 3 жыл бұрын

Thank you guys, this is Awesome guide! Im ready to order parts from your online store, but I need also additional parts as bearings and seals. I didn't find it on your site. can you add full parts list for this procedure? Or make replacement kit for rear axle that will include seals, bearings pads and rotors.

@socialemotion 4 жыл бұрын

Great no nonsense video, With this clip I think I could 'Do the job' , thanks for posting, good camera and lighting work 10 out of 10. Don.S

@Moes_Adventures 4 жыл бұрын

Excellent, professional quality video! Every single step explained in detail.

@PhilipWahlbom 2 жыл бұрын

Outstanding job at making this 5-star instructional video! One of the very best I've ever experienced on KZfaq. Thank you very much for your effort at putting this together.

@jamesholliday6151 3 жыл бұрын

Wow. I own a 2013 F450 and need to change the rear brakes but did not realize how much work was actually involved. Thanks for the video.

@ronymorales3527 2 жыл бұрын

Parts are expensive

@dubsey98 2 жыл бұрын

Its not a a bad job at all to do in an afternoon boss! Just eat your weeties for breakfast cuz although its not a bad job its a tad on the heavier side lol

@leslieross3404 4 жыл бұрын

Well explained and thank you for saying the torque settings as you went.

@mactheplumber3839 Жыл бұрын

I wish i could find a mechanic half as thorough as you are. You are a true craftsman. Ty for this video man, really helped me out with my project.

@fantastic_george6123 Ай бұрын

This video made me feel a little bit better about why the dealership charged me so much for brakes.

@gravytrainoutdoors 2 жыл бұрын

Gotta love having a proper seal installation kit with the right sized bushings! Good job getting that seal seated without damaging it. I know I would have crushed it haha

@raider762 2 жыл бұрын

Thanks for the video. Tried to upsale this job on a used F350 I was processing for a dealership. They said no and wholesaled it back to the auction with it. Now I know what I missed.

@ggrebenyuk Жыл бұрын

I like your videos--precisely what DIYs need. I was looking for some direction of how to remove rear output transfer case shaft seal on my 2016 Ford f250. It has a leak from the output shaft.

@philbg6378 3 жыл бұрын

Very professional and well executed! Explained as well, keep more videos coming. Thx!

@TRQ 3 жыл бұрын

+Phil B G Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

@leonelcotto6141 Жыл бұрын

Amazing I love to do everything on my truck and cars thank you for the video it’s very well explained

@rickmorales3214 3 жыл бұрын

What size is the Spindle Nut Socket? I’ve seen a couple different sizes. I have an 04 F350 super duty dually king ranch 4X4?

@74stevedc 2 жыл бұрын

Just did new pads and rotors 2015 f550 I didn't add gear oil like you did at 13:10. I was wondering if I fill the rear end filler plug will it go down axle to these bearings? I really don't want to take it all apart again. Thanks

@ChrisR1270 10 ай бұрын

Great video! I appreciate the clear instruction with each step. I have a 2017 f350 4x4 6.7, single rear wheel. Are the torque specs mentioned the same on the single rear wheel trucks? Thank you.

@m.c.4574 2 жыл бұрын

Will this procedure also apply to a 2016 F-350dually also what is the part number of the tool needed to take the center bolt off Great INFO

@ellkir1521 2 жыл бұрын

Doing this job now. Unfortunately, mine has a grooved inner ring for what I assume is for ABS or a speed sensor I can't get off the ring or find a part to replace. I have 2014 Monaco Motor home on a F35 frame chassis. Any ideas?

@photomasterstudios9495 2 жыл бұрын

using this video as a reference since the rear bakes and axles are virtually identical to my 1999 f350 superduty dually and i do not have the e-brake for some reason.

@Taterhead3e 3 жыл бұрын

when removing the hub locking nut, sorry is the pass side reverse threads or standard

@abibodlogistics 2 жыл бұрын

How do you know or confirm that the orange/brown seal or what colour is it that is sitting on the bearing that you start installing at 9.00 minutes that you used a wood to beat in is well seated or should I say is properly installed.

@reycelmartinez7945 Жыл бұрын

Will this process be the same for a 2008 F-350? Thank you.

@NGALABDULLA 2 жыл бұрын

Hi, I want the name of equipment that you used it to open Lock Nut. Thank you

@guille15784 2 жыл бұрын

This is the best video explaining how to do the rear brakes on my truck. Thank you.

@rynely1 7 ай бұрын

This video is very informative. Very helpful for a step by step, while doing a job

@TRQ 7 ай бұрын

+@rynely1 Thanks for watching. Buy the part in this video on 1AAuto.com: 1aau.to/m/Shop-TRQ

@NoahPARK82 Ай бұрын

Hi there i just want to know if i need to do grease pack on bearings, thanks

@PlainStraightShooter 3 жыл бұрын

One more thing, those salty areas like the coast and northern country are hell on these wheels and axle center. We stated using a mild coat of grease when installing, so far the come backs for tires and or brakes or coming off Way better.

@rafatqaryouti2107 2 жыл бұрын

Can you tell me please what the silver part on minute 12:49 called please? And how can i find it on your website? Does it call rear spindle or what ?

@1977starfire 3 жыл бұрын

You need to grease the seal before installing. It would also make sense to use some high temp grease to grease the bearings until the gear oil will fully supply them when you start driving.

@TRQ 3 жыл бұрын

+Ewald Rindlisbacher Thanks for watching our video! 1aau.to/m/Shop-TRQ

@VWBUGSAM 3 жыл бұрын

Thanks. Very detailed. Will help a lot.

@salinasvalleytowing7842 Жыл бұрын

Would it be the same for a 2017 F-550?

@tacsnoopy3000 3 жыл бұрын

Great video. Just want to make a recomendation that you crack open the bleeder screw when you push the brake pistons in so you dont force any dirty fluid back into the system.

@TRQ 3 жыл бұрын

+Eshedal74 Thanks for the tip! We'll pass this info along to our production team. 1aau.to/m/Shop-TRQ

@lonnieblackwell5107 3 жыл бұрын

Great idea!

@larsbambi1575 Жыл бұрын

Will that require us to have to bleed the brakes? I'm a newbie when it comes to the big trucks..

@sfranklin3896 3 жыл бұрын

Excellent video👍👍👍👍

@IndianTruckWorkshop 3 жыл бұрын

Great work buddy 👍👍

@pepelepew158 3 жыл бұрын

Are you going to do the passenger side as well.????

@jaytek5680 11 ай бұрын

How do you adjust the e brake on the passenger side? It don’t look like the side you did. The cable is were the hole should be to back the e brake off!

@richtenorio3119 3 жыл бұрын

What's that's socket drive called the 4?

@dubsey98 2 жыл бұрын

Use axle bearing grease where he uses vaseline and use alot of it. Fill the cavity in where the spring is. Id rather know for a fact that spring wont move then habe to take it apart again. Ive learned the hard way. Done dozens and dozens of these. Also. Instead of going nuts with the impact on the e torx bolts holding rotor to hub I've always gone and torqued those bolts to the same spec as wheel lug nuts. And on this truck should be 150-165. Good luck!

@edgarcastro149 4 жыл бұрын

Great video!!!!! Thanks.

@d-rock8612 8 ай бұрын

Do you have to remove the axle to change rear brakes

@danmarshall2340 4 жыл бұрын

What is the part number for the 4 point locking nut tool you used? Thanks for the video

@frankalonso384 Жыл бұрын

W83008 Amazon. 2 3/4 . Or Napa has a equivalent one

@alhuntington6208 4 жыл бұрын

heal bar to pull seals life saver

@ronymorales3527 2 жыл бұрын

Great great video helps a lot

@miano07 Жыл бұрын

After watching this video I don’t think I want to own a DWR anymore. I’m good with. SWR. But nice and informative video BTW!

@alejandrocarmona802 Жыл бұрын

Excelente trabajo saludos.

@scottdonbrosky5968 2 жыл бұрын

You are taking the chance of damaging the hub seal area by using the pry bar and air hammer. I’ve literally done 1000s of these by using end cut pliers. Easy as pie. Also a seal driver or a same size piece of tubing works better for seal install. Not getting those wheels off that easy in the north lol. Upsets me nobody uses torque wrenches.

@cherilcooper289 3 жыл бұрын

How much did the customer pay for this job? Also did you do the front brakes? Thanks loved the video. 🥰🥰😊😊

@nicholscorcoran3138 3 жыл бұрын

I just did this on a 2018 f450 and now there’s a squeal when moving any idea what it could be, I just rewatched ur video and realized I didn’t put any vaseline on the seal would that cause that, do I have to take it back apart?

@jesusguerrero7732 2 жыл бұрын

Did you find out what was causing that squealing?

@sureshKumar-zr6pp Жыл бұрын

What is the number of this big socket

@ferntube187 2 ай бұрын

I’m having a hard time accessing the rear passenger adjustment its the on the opposite side

@syncrosimon 11 ай бұрын

Great job.🏴󠁧󠁢󠁳󠁣󠁴󠁿🏴󠁧󠁢󠁳󠁣󠁴󠁿

@robinlopezchacon4670 Жыл бұрын

Muy buen video broth pero seria bueno que explicara como sangrando tambien

@garand70 Жыл бұрын

This same procedure works on a 2008 F350 also. All the same parts.

@jamesrichardson5584 3 жыл бұрын

So do the drum brakes assist the disc while stopping? Or do the discs work alone while braking?

@TRQ 3 жыл бұрын

+james richardson On most vehicles the drum brakes under brake rotors are the parking brakes. Thanks for watching our video! 1aau.to/m/Shop-TRQ

@clinkerclint 3 жыл бұрын

I enjoyed the video but the rear axle retaining bolts torque spec is 80 ft lb, not 188! Please fix this in your video or take it down so somebody else doesn't ruin the rear hub like I just did. My fault for not checking the torque specs myself.

@JohnLee-cb8ez 3 жыл бұрын

Yup. 188, it is not! Plz correct it. I bet I am not the only one to torque it that high after watching this video. In the video, u don't look like u r doing that high either. U just state "188".

@abibodlogistics 2 жыл бұрын

I am a little bit concerned here, why use a Vaseline instead of the regular grease.

@rustyshackleford2525 3 жыл бұрын

Is he going to bonk it????? Lol!!

@ramiroarellano8496 Жыл бұрын

I can see that you love what you doing just like me 🙏🙏👌👌👌👌👌 but I’m just a Beginner

@stahpit1971 3 жыл бұрын

curious as to why not install new bearings while you have them out

@corysturgis6660 3 жыл бұрын

No need if they look good. A visual should be fine on a truck.

@Taterhead3e 3 жыл бұрын

your doing the driver side correct,,,lefty loosey, correct,,,, what about the passenger side ,,is it the same OR is it reverse thread

@TRQ 3 жыл бұрын

+taterhead 3e The threads should be the same on both sides.

@Taterhead3e 3 жыл бұрын

nice video

@TRQ 3 жыл бұрын

+taterhead 3e Thanks for watching our video! 1aau.to/m/Shop-TRQ

@dylanbutler7804 2 жыл бұрын

Anyone else break a axle shaft bolt around 100ft/lbs they started stretching not tightening no way 188ft/lbs is the correct spec

@htatesil4192 Жыл бұрын

Lol that definitely wasn't right

@spike555 2 жыл бұрын

On my 2020 E450 the top caliper bolt can’t come out. The springs are in the way. The only way to replace the brake pads is to remove the bottom caliper slide bolt, pry the caliper up, remove the old pads. Then push the caliper all the way in towards the springs, then lube the slide pin as well as you can. Then put everything back together. How in the hell do I get those top bolts out?

@sweeperofthestreets6261 2 жыл бұрын

remove the caliper bracket

@htatesil4192 Жыл бұрын

I have the video how top do it check my page

@barrymesecher9948 Жыл бұрын

Whoa you have to pull the axle to change the brakes. Wow

@jamesfolz3139 Жыл бұрын

Loving bonks

@cartercheek7605 10 ай бұрын

This is where I do one side and go "eh the other side is probably ok"

@MP57719 2 жыл бұрын

At 1:40, what are you prying against?

@LunaDaSavage Жыл бұрын

The old rotor foo

@PlainStraightShooter 3 жыл бұрын

I don't tell anyone what to do but, I use a seal tool, rent or borrow or own it,, Second I pack a little grease on my bearings because, I change the diff grease and this way you have a positive lube on the bearings when you roll out, Mind you, I and my buds ease out to a ditch or lean and let the new oil or grease run to each side and then come back and top off. REASON>>> In the early 80's we seen a lot of oilfield company's running these jobs themselves and they was having bearing failure. Being at a Ford garage we questioned the job, What I recommended was not what they did. They actually was running a dry or semi dry bearing to long right of the bat. Axle, not that what you did want work with a Love tap but not recommended. Usually one good deadblow to the center of the axle face will pop that axle right to you, it might take a couple but never the back face of axle. Outboard style drums and or rotors have changed the game A LOT. Hope someone sees a tip or advice hear.

@paulweaver2417 3 жыл бұрын

My rear tires are wearing on the inside how do I correct that

@corysturgis6660 3 жыл бұрын

Lube you glide pins. Maybe flush out you lines and calipers

@larsbambi1575 Жыл бұрын

@@corysturgis6660 I'm not an expert but I think it would have something to do with the suspension.

@ironworkerfxr7105 3 жыл бұрын

you could only WISH the dealer did it like that ................ nice job !! ,, the reason why I could never make book time .....

@TRQ 3 жыл бұрын

+Ironworker FXR Thanks for watching our video! 1aau.to/m/Shop-TRQ

@FRZNTYM1 10 ай бұрын

I was thinking the same thing. Would the tech take all those extra steps to clean mating surfaces and other steps this guy did. I highly doubt it. This was a job well done.

@DJDoubtIt81 3 жыл бұрын

How much should this job cost per side at a shop?

@TRQ 3 жыл бұрын

+Matthew Bolt Thanks for watching! We do not have that information available.

@stahpit1971 3 жыл бұрын

that means hold to your socks.

@raider762 2 жыл бұрын

Parking brake could have used some new springs. Those old ones are rusty and will snap.

@98prera 3 жыл бұрын

My truck is a 1999 Ford F-350 dual it’s the same process for my truck??

@TRQ 3 жыл бұрын

+El Tigre This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-TRQ

@theturtlethebanjo195 7 күн бұрын

Looks like your doing all this in a shop w ac. Must be nice 😂 go do all this in a 95° shop

@automotivemechanic1111 2 жыл бұрын

never heard of a seal driver eh

@t20594 2 жыл бұрын

PN 205-1070 Dana axle 205-1069 Ford axle $300 a piece. No aftermarket options. Backordered until December. I had to follow his hack instructions after I met that brick wall.

@chevy050 3 жыл бұрын

I think ill just pay a shop to do this lol

@14paste14 3 жыл бұрын

He didn't pack the bearing

@tylerallison1 2 жыл бұрын

They don’t need packed, they’re oil filled bearings.

@phillipdrake4371 7 ай бұрын

13:10 yeah buddy I agree

@TRQ 7 ай бұрын

+Phillip Drake Thanks for watching our video! 1aau.to/m/Shop-TRQ

@guacamoleweiner69 3 жыл бұрын

B O N K

@htatesil4192 Жыл бұрын

TORQUE AXEL BOLTS TO 75 FT POUNDS HE STATES 188FT POUNDS WILL STRIP YOUR HUB

@LunaDaSavage Жыл бұрын

Squirt Squirt 😂

@gml326 3 жыл бұрын

Screw that i will stay single tires on my F-350

@thedrmmr5 2 жыл бұрын

13:09

@vikp7885 2 жыл бұрын

I can't understand ,why you have removed a hub, to change the brakes, unless customer told you to change the rotor ,otherwise no need to do all of this to just change the brakes ,to change parking brakes, yes it is need to do all of it

@skyhawksailor8736 3 жыл бұрын

Could you please show me any owners manual, or driving manual which states "Emergency" Brake. I have only seen then officially referred to as "Parking Brakes". I know they can be used in an emergency, but with any Ford Heavy Duty, if I had to use mine while towing a trailer, I know they would not be able to stop the truck in an emergency. You might want to check with your Lawyer to find out if you referring to them as an Emergency brake, if you are exposing yourself to a liability if a person has a crash and they thought you telling them it is an Emergency brake, if you could be held liable for damages suffered.

@TRQ 3 жыл бұрын

+Skyhawk Sailor While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

@scottwall8917 2 жыл бұрын

Shut up karen.

@SergioMendozaify 3 жыл бұрын

188 foot pound? that is too much🤔 rear axle shaft bolt

@corysturgis6660 3 жыл бұрын

I was thinking that seemed high too.

@FranciscoHernandez-dq7rf 7 ай бұрын

Not a regular 50 dollar break job lol

@Niafi11 Жыл бұрын

Dude I would NEVER Let you Pry on my Wheels like that. No Sir Man. Mine come off just fine from 2 inches off the ground. Also, did you just say Veer-icle?