1999 2016 Ford F350 Dana 80 DRW Rear Hub Service

Рет қаралды 36,970

Жыл бұрын

TorqueKingTV presents: Ford F350 Dana 80 Dual Rear Wheel Hub Service! Covers 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016 Ford DRW trucks with Dana 80 rear axle.
Purchase here: torqueking.com/category/1999-...
If this content helped you find a part you need, please consider giving this video a like, comment, and subscribe! Thanks for watching, and good luck keeping your rig on the road!
Follow us on social media! For daily happenings here at TorqueKing4x4
Instagram: torqueking4...
TikTok: / torqueking4x4
For Product Updates, Announcements, and more, We're hiring.
Facebook: / torqueking4x4
Twitter: / torqueking4x4
Read our weekly blog here: torqueking.com/blog/
TorqueKing4x4 is a USA based manufacturer, stocking OEM parts distributor, and exporter of a large selection of 4x4 special tools and genuine original equipment parts.

Пікірлер: 26

@j.onofre6613 Жыл бұрын

Exactly what I was looking for.. thanks. Very good explanation and professional..

@tuckswanger 7 ай бұрын

Thank you for the precise workmanship and specifications on the complete removal and installation even my manual doesn't explain it like I wanted until I found your work. Thank you so much. And may GOD continue to BLESS you

@anthonybuchanan4848 2 ай бұрын

Great video! Thanks!

@israelroque3921 7 ай бұрын

Nice video. You have all information about this job. Thank you for give your knowledge .

@goomba.1866 10 ай бұрын

Thank you so much,for teaching r....from Mexico

@TheRealSlowhand Жыл бұрын

Great content, thanks...

@HotShotMike 4 ай бұрын

Thank you for saying the name size of the spindle nut nobody else did

@EDROTH-mp3om Ай бұрын

Rare emergency brake assembly

@igoturparts20 3 ай бұрын

Just wanted to add this, i had made the mistake a few years back by not packing these bearings, thinking that the differential gear oil would keep them lubed, and i ended up replacing the entire axle a few months later as the bearings overheated, siezed and spun on the ends of the axle, ruining the whole thing. Needless to say, i learned my lesson on that! Quick side note, the slighly narrower cab/chassis axle fits fine if u remove the old spring perches and weld new ones in the proper location...

@DieselMike 5 ай бұрын

What would be the ill effects of over tightening or improper torque procedure for the spindle nut? Reason I ask is because I did this service on my SRW F250 Sterling 10.5 about a year ago. Whereas the torque specs are slightly different for mine, the concept is the same as it's that same style ratcheting nut. But now when I was doing a brake job, I notice the hubs are stiff as hell. I certainly can't turn them without the use of a pry bar wedged between the lug bolts. Let me mention, I have not noticed any drive-ability issues. Noises, clunks, grinding, etc. Any suggestion on what to do next?

@TorqueKingTV 5 ай бұрын

First thing to do is make sure there is no brake drag, including park brake shoes. Once that is confirmed, unbolt the axle shafts to confirm drag is not coming from the differential. Improper procedures will result in premature bearing wear or complete failure. Once you isolate the friction source, that will determine the repair procedure.

@DieselMike 5 ай бұрын

@@TorqueKingTV Thank you for the response. It is not brake drag as I have not only the calipers off, but the rotors too. I will pull off the shafts next and test. If there is still tightness at that point, it's the spindle nut? But if it frees up then it's an issue inside the differential? I have that correct?

@TorqueKingTV 5 ай бұрын

@@DieselMike The ratcheting nut shouldn't let preload get so tight that you need a pry bar to rotate the wheel, but it could do some weird stuff to bearings over time. If resistance is still local to the wheel after pulling shafts, it is definitely time for bearings. If they free up without shafts, its time to pop the differential open.

@DieselMike 5 ай бұрын

@@TorqueKingTV This is very helpful information. Thank You.

@speciosa146 3 ай бұрын

Do you have any similar videos on the dana 135 in the f550s?

@TorqueKingTV 3 ай бұрын

I believe we have published the S110, which is similar. We have not acquired larger axles for video yet.

@tylerdunn6578 3 ай бұрын

I have a single rear wheel drive Dana 80 on my 99 1/2 f250 I was told on the tag 373 gears and that it was a one ton Axle my question is when I seen you pull disk/drum off and apart it looked like mine ? Is it possible to make mine a dual wheel set up. I would appreciate an answer it looks like I would need the dual drum/disk to bolt to my hub I appreciate the information.

@TorqueKingTV 3 ай бұрын

Ford only uses a Dana 80 in DRW applications... Single wheel was limited to Dana 60 and 70, but Sterling axles are more common. Generally speaking, a SRW uses a larger inner wheel bearing and that limits hub interchangeability. We do have some spacer adapters available for this conversion but we need to verify which axle it is. Send us axle pictures to sales@torqueking.com and we can evaluate your options.

@_Pearls4Swine 10 ай бұрын

How close is this procedure to a 1998 ford Superdry e-350 class-c motorhome dually. Cant find shit for torque specs...

@TorqueKingTV 10 ай бұрын

If it's the ratcheting style nut, nearly identical procedure. If it's a 1-piece Nyloc, its a little different. Exact procedure can be found on the FordServiceInfo website or a factory manual from Bishko. Parts: torqueking.com/category/spindles-1996-2000-e350-dana-80r/