How to Replace Front Window Regulator 09-16 Mercedes-Benz E350

Рет қаралды 52,241

4 жыл бұрын

Buy Now!
New Window Regulator from 1AAuto.com 1aau.to/ia/1AWRG02096
Most power window problems can be traced back to either the regulator or the motor that drives it. TRQ produces affordable window regulators and motors that are designed specifically to fit your vehicle! This video shows you how to replace both the window regulator and the motor on your 2009-16 Mercedes-Benz E350.
• Check here for more videos on the 2009-16 Mercedes-Benz E350: • 2009-2016 Mercedes E350
This process should be similar on the following vehicles:
2010 Mercedes Benz E350
2011 Mercedes Benz E350
2012 Mercedes Benz E350
2013 Mercedes Benz E350
2014 Mercedes Benz E350
2015 Mercedes Benz E350
2016 Mercedes Benz E350
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXAA00013
• 10mm Socket 1aau.to/oa/1AXAA00017
• Rivet Gun & Rivets
• Trim Tool Set 1aau.to/oa/1AXXX00004
• Side Cutters
• T25 Driver 1aau.to/oa/1AXAA00008
• T30 Bit 1aau.to/oa/1AXAA00008
• Ratchet 1aau.to/oa/1AXAA00016
• Drill
• Drill Bit Set 1aau.to/oa/1AXAA00141
• Painter's Tape
• Grinder
• Hammer 1aau.to/oa/1AXAA00091
Subscribe: / @trq
Check out our playlist:
2009-2016 Mercedes E350: • 2009-2016 Mercedes E350
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 51

@TRQ 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@MadCloudDisease 3 жыл бұрын

How tight should the 10 mm "U Channel" bolts be torqued to, or should they be tightened all the way down? Thanks in advance

@sampsonpaintsil9839 Ай бұрын

Thanks for the video,you saved me lots of money,the dealer ship wanted$2600.00 to replace it,it cost me,tools and the regulator mechanism less than $300 to get it fixed by watching this step by step guide.Thanks.

@scottscruggs9541 3 жыл бұрын

I watched a few video's on this subject, and yours by far was the best! Thanks...

@trey8482 11 ай бұрын

For anyone asking about the rivet size. The rivets for the regulator and panel are 1/4. The small one he grinds down is probably 5/32 or 3/16. I brought the exact rivet gun he's using from Harbor Freight for $20. It comes with 10 1/4, 3/16, 5/32, 1/8, and 3/32 rivets. So, you'll need to buy extra 1/4 rivets.

@TRQ 11 ай бұрын

+Trey Thanks for watching our video! 1aau.to/m/Shop-TRQ

@dhubbard 9 ай бұрын

Awesome video. Just finished the project - saved me a bunch of time and some money. Again, thanks!

@mmcknight5492 Жыл бұрын

RESEARCH! great video for sure, but after watching a couple other videos, one showed removal of handle. I realized it was better to remove outside handle and 3 door latch screws to eliminate the risk of messing with the white plastic tabs that you pushed inward and the 1 rivet you ground off (5:29) that are very difficult to put back. It looks like you had to rivet the white plastic tabs to stay in.( see at 13:54 ) it also eliminates the need to remove the wire harness to the handle. I think it saved time. Still great quality video. Couldn’t have done it with out you. Big Thanks.

@letruong1 Жыл бұрын

Could you send the link of the video showing how to remove the outside handle? Thanks.

@deighdreamer Жыл бұрын

yeah ima gone head and make an appointment to have it done lol. You had me until you started drilling rivets and pulling wires

@bruceleeroy1245 3 жыл бұрын

This was a great video I'm doing a broken one now I usually work on gm and am still in automotive school. But I appreciate your attention to detail you basically did the job for me 😁

@TRQ 3 жыл бұрын

+Bruce leeroy Ransom Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

@Jaang29 2 жыл бұрын

thank you for this video sir ! much appreciated, hello from Miami, FL , fi ever in Florida, LKM to buy you a drink

@Brian-no6rl 2 ай бұрын

My window was stuck all the way down, I used some gorilla tape and stuck some pieces onto the glass and was able to pull it up. I then taped the window up until I was able to replace.

@Sheikh7 2 жыл бұрын

Thanks a lot for this detailed video , I successfully replaced broken regulator of my 2014 E350, 4Matic - Cheers

@elijahsurall782 2 жыл бұрын

What size were the rivets bro? Any recommendations on tools to have too?

@Sheikh7 2 жыл бұрын

@@elijahsurall782 1/4 inch rivets, four came with the part and rest (qty -8) bought from NAPA Auto Parts for $6.95. 1/4 inch rivet gun from Home Depot - Surebonder 1/4 in. Heavy-Duty Rivet Tool. Very easy to use.

@Fkzionism 3 жыл бұрын

Great video, regardless if its broken or not its the ENTIRE job. Others have no common sense i guess. Great job.

@TRQ 3 жыл бұрын

+Yes Its me Thanks for watching our video! 1aau.to/m/Shop-TRQ

@serg2915 Жыл бұрын

Great video! Does anyone know the Rivet sizes for the regulator?

@emilioc414 2 жыл бұрын

Should do a rear one or is the same concept even though you have the shades in the rear ??

@martinrivera2950 2 жыл бұрын

How did he get his hand behind that panel for those three plastic pins

@JesusHernandez-co3no 2 жыл бұрын

Will the part for this particular Mercedes fit a 2012 Mercedes Benz GLK 350?

@princenoyan893 Жыл бұрын

Thank you bless up

@adam1035 2 жыл бұрын

Having difficulty reinstalling the plastic plugs. They video at 13:00 cuts away. How are you holding the part on the backside? When I try to knock in the plugs the part pops in also? Any help would be appreciated! Other than that. They video is great and detailed. Saved me a lot of $$.

@aiwoor 2 жыл бұрын

you can see that hes holding it with hes hand and a friend is kocking them in with a hammer.

@paulsinglevich8425 3 жыл бұрын

Done right!

@newmexicojoe5443 11 ай бұрын

Right off the bat.....if your regulator cable broke and glass went down into the door, youre not gonna be able to get those first bolts out. The glass slides down so far its near impossible to slide it back up.

@BotMechanic Ай бұрын

Having a really tough time with those 3 plastic rivits around 13:00 anyone find a way to do these? Been trying for over an hour

@understandthis4634 Ай бұрын

Save time. Just remove the speaker and get old regulator and new regulator through the speaker hole. No need to remove rivets from panel.

@DevonBbrown 8 ай бұрын

Great video.. I'm just curious on why you changing a window regulator and motor that obviously works perfectly. 99.999% of us watching are trying to change a broken part so how to get the window up when the parts are broken would be a really helpful video

@carltonmcmullen8396 Жыл бұрын

Hi I am in the middle of replacing my regulator. Can anyone tell me the name and size of the fasteners that he points out at 5:00 mark and also the part that he grinds off at 5:30.

@MarkRadfordAZ 3 жыл бұрын

I've ordered the replacement part from you. I think it was asked but not answered: please identify the rivet sizes used, both for the regulator itself and the door panel? Also, my window is down, and of course can't pull it up and tape it now. Any tips for removing the aluminum panel without damaging the glass? That kind of stuff would help these videos a lot. Grind the rivets maybe? Thx!

@MarkRadfordAZ 3 жыл бұрын

Careful drilling of the regulator rivets (but not drilling "through" those or the others) was the solution.

@briansc6104 2 жыл бұрын

This video is missing some VERY important information regarding linkage for your door handle.

@deansynan7424 2 жыл бұрын

It would help to show the video of how to reset the automatic window settings right after this video. Or edit that part into this one. Redoing all my work because I did not know that the window needed to be programmed with the engine off and hold the up button for 30 seconds and then the down button for 15 to 30 seconds. IF THE WINDOW GOES UP AND COMES DOWN ABOUT HALF AN INCH IT MUST BE RESET OR THE CABLE BREAKS AND YOU GET TO DO ALL OF THIS AGAIN. . .PRO RIVETER NOW!!!

@jonahgomes9710 2 жыл бұрын

I tried this and it didn’t work, are there any more details other than what you wrote?

@justinelias9147 4 жыл бұрын

Nice work, but Kind of Pointless video, replacing a regulator that still works. Please show how to remove the glass when the regulator is actually broken stuck down and does not roll up at all.

@justinrobert6573 3 жыл бұрын

It helped me? Half of mine was completely ripped out and coiled around the motor.

@keithparsons672 3 жыл бұрын

Removing the motor sometimes will allow the window to be lifted up if its stuck at bottom. The motor can be removed from the front with 3 screws

@billkirkpatrick2054 3 жыл бұрын

My problem also but in the end I decided to drill out the 5 rivets that hold the regulartor to the inner panel thus freeing it from the panel. Biggest remaining problem i have is understanding how to remove and then replace the 3 plastic rivets.

@MarkRadfordAZ 3 жыл бұрын

@@billkirkpatrick2054 Thanks for this comment, carefully drilling and then chiseling the regulator rivets seems to be the only solution to getting to the glass. Just be careful and don't "drill through" the rivet or bad things may happen to the glass :)