How To Replace Rear Struts 2007-11 Honda CR-V

No video

How To Replace Rear Struts 2007-11 Honda CR-V

Рет қаралды 66,036

Күн бұрын

Buy Now!
New Strut & Spring Assembly from 1AAuto.com 1aau.to/ia/1AST...
TRQ Struts are made to fit your vehicle exactly, just like the original part. Struts can wear out as early as 50,000 miles. You should inspect them regularly for leaks or wear. Save time, money, and hassle by replacing an entire strut assembly. This video shows you how to install new reliable TRQ struts in your 2007-2011 Honda CR-V.
• Check here for more videos on the 2007-2011 Honda CR-V • Honda CR-V 3rd Generat...
This process should be similar on the following vehicles:
2007 Honda CR-V
2008 Honda CR-V
2009 Honda CR-V
2010 Honda CR-V
2011 Honda CR-V
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXA...
• Pry Bar 1aau.to/oa/1AXA...
• 14mm Wrench 1aau.to/oa/1AXA...
• 12mm Socket 1aau.to/oa/1AXA...
• 14mm Socket 1aau.to/oa/1AXA...
• 17mm Socket 1aau.to/oa/1AXA...
• 19mm Socket 1aau.to/oa/1AXA...
• Straight Cutters
• Ratchet 1aau.to/oa/1AXA...
• Socket Driver
• Socket Extensions 1aau.to/oa/1AXA...
• Torque Wrench 1aau.to/oa/1AXA...
• 5mm Hex Socket
• Floor Jack 1aau.to/oa/1AXA...
• Jack Stands 1aau.to/oa/1AXA...
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Honda CR-V 3rd Generation 2007-2011: • Honda CR-V 3rd Generat...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Пікірлер: 37

@TRQ 3 жыл бұрын

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@wanbrother9242 3 жыл бұрын

The tip about removing tab on old strut helped me remove them. I didnt need to cut them off, just bend it upward so it wont get caught. Also didnt need to remove bar end link or brake line holders.

@glennsmith8949 9 ай бұрын

This Is The Best How To Video I've Ever Seen,, Straight to the point an No Back ground noise,, An better Yet,, No Music 👍 Thank you So Much .....

@Ganin17 Жыл бұрын

The six 12mm bolts holding the rear damper gusset/cover, that he says to snug down at about the 7 minute mark, should be 22 ft-lb per the Honda Sevice Manual.

@charlesvail2443 9 ай бұрын

If your Honda has had the trailing arm mounting point recall repair done be careful when aligning the bolts that you don't strip the threads. The added plate can make alignment difficult. Try to loosen the additional front mounting bolt at the front of the new reinforcing plate. You might need three hands. Here is a link to the the Honda recall service repair.m.kzfaq.infoJ4kzJecRZCc

@ronm3380 3 жыл бұрын

Excellent video! Explains replacing the struts very clear. Thank you for the torque numbers too.

@georgelegge3393 2 жыл бұрын

Great video, couldn't get the stabilizer link off (rusted Allen head) but pulling the 2 stabilizer mount bolts out worked just as well. No tabs on either my old or new strut

@user-xz3zd5gu1z 2 жыл бұрын

Great work dude! I was to install a set of adjustable struts, and wondering how shall I adjust the rear one. Knowing that the cover could be easily removed really makes me happy.

@barrybajuk8835 2 жыл бұрын

Very thorough / concise video instruction thanks.

@jeflores1000 Жыл бұрын

Great video on removing those rear struts.I wouldn't have caught that lock tab thank you!

@parsineo Жыл бұрын

Getting the two bolts back into the body can be a real B if your car decides it doesn’t want to cooperate. Have plenty of different size pry bars! You’ve been warned.

@tonyjordan1320 Жыл бұрын

Do you have to get a alignment if you just change out the rear shocks/struts on the CRV?????

@NoxPark 7 ай бұрын

From a different source, the torque of the two trailing arm mounting bolts is 84.6 lbf-ft(=11.7 kgf-m). There is a big difference between 54 and 84.6. Would you please double check it?

@Superchad245 6 ай бұрын

Is it possible to use a spring compressor to replace the strut without removing the control arm bolts and not lowering the control arm? after Honda did the rear subframe repair the bracket for the repair goes over the front bolt of the control arm requiring removing the entire recall repair bracket in order to lower the control arm.

@mattrinaldi8828 7 ай бұрын

What’s the difference between the 2nd gen and 3rd gen rear struts? They seem identical but are listed as different parts

@glennsmith8949 3 жыл бұрын

Thx great video.

@patrickvincent2477 3 жыл бұрын

Awesome thank you !!!

@jjsoundguy Жыл бұрын

At 5:47 the second bolt was over-torqued. The proof is the torque wrench did not move before the wrench clicked. All this proved is the bolt was at least 54 ft pounds. Could have been 65 or 75, you cannot tell unless the bolt turns before the wrench clicks. Over torquing is bad too. So many people don't torque bolts properly. Otherwise nice video. Thank you.

@luismiguellandrau5601 2 жыл бұрын

Thank you very much for the Information

@stevendomenech7405 Жыл бұрын

EXCELLENT video

@la1negrita Жыл бұрын

Perfect video

@harwoods11 3 жыл бұрын

Did you replace both sides?

@streamingeagle1 Жыл бұрын

looks like you dont need to remove the interior top section at all.

@kjdcomp1 2 жыл бұрын

Good video thanks.

@Bolek_i_Lolek 3 ай бұрын

You didn't even clean and lubricate the rusty screws? Was it necesarry to demount stabilizer link and brake hose?

@user-oy8zc9gr2u Жыл бұрын

Aque lado lleva el amortiguador RR

@djmaurymedina9822 Жыл бұрын

Hello, do these shock absorbers fit a 2011 crv exl?

@TRQ Жыл бұрын

+Dj Maury Medina This part is listed to fit a CRV.

@motorsandvoltsandrobots7162 2 ай бұрын

Don't take the cover off. Its a waste of time . Absolutely just causes issues . You don't have to take the sway bar links off either .

@TROLLthatShanks 2 жыл бұрын

I think they have a dog

@Steven-xj2rf Жыл бұрын

We can only hope.

@The_Defiant_One 3 жыл бұрын

Runs the compressor empty with a 1/2" impact... "Now torque this nut down to 10 inch pounds"

@domingodelgado3944 Жыл бұрын

Worked in a dealership for 8 years. Only time we torqued was on engine work 😂.

@user-iw4qs5zs8b 9 ай бұрын

Please learn how to properly use a torque wrench.... 3 ugga uggas with an impact and then torquing is not the correct way...

@RandomPerson-sb5mw Жыл бұрын

This video shows why having pets is terrible for your vehicle.

@raduarfloe8528 Жыл бұрын

Why are you doing all these unnecessary steps? I’ve seen the video from 1a auto and it’s much easier

@barrybajuk8835 2 жыл бұрын

Very thorough / concise video instruction thanks.