You’re the Best Example I have seen of an Overqualified Truck Mechanic. 👍

Welcome back Monday morning October 5th local time 9:03 a.m. temperature 50ﾟ year 2020NC

Wow Larry! 794 needed a lot of work! I'm sure you saved the boss a whole lot of money!

They make a bearing ,racers, sealer puller an installer kit for that type of work had to order one yesterday replacing my timing chain gasket, saw one for a Peterbuilt.

Another great video by Larry

👍The Cone - GREAT IDEA!!! - I can't tell you how many times I've had trouble over tightening wheel bearings. Used to just keep spinning the hub until it "free spined" then checked side to side & in + out slap & hoped for the best.

I use a Hydraulic press never a problem. Plus with a pre-set bearing system you just need to torque the nut to the correct setting to get the correct clearance. You learn something new every day.

Great explanation on race removal/installation. Exactly how I do it.

Great Repair Video Larry. Have a good week and stay safe....

Great lesson and video....Thank YOU

One easy way to find a parasitic draw is with a temperature sensor pistol. Use it on the fuse box, warmest fuse is usually the culprit. Then trace out that circuit to the problem.

GM LHL, as far as bearing races go, we freeze em, so they pop in lit' bit easier, stay well...peace

I enjoyed the class, thanks.................

Im a Journey man trailer mechanic run a weld bead on the inside of the races put the new races in a freezer so they shrink a bit the cold races will pound in way easier and the welded races will pound out a lot easier as well.

Nice work...

Unsafe hitting two cups together , the hard surfaces will splinter and chip ! Always wear safety glasses . Heat aluminum hub surfaces up to drive cups out and in place .

Have a good day larry.

I thought with the cone you didn’t have to back out but…just straight ft pounds of torque. 200!

You are the man

Our favorite grease monkey is racking up the videos recently! 👍🏼

Water oil mixes together makes it soupy. Oil for rainbow color oil water. Grit in my oil from shavings engine repair or clear color.

Real nice👍👍👍

Sir Larry !! Saw some things that are questionable ,,but GOOD Job & Thanks !!! ""KEEP IT SAFE ""!!

Good morning long hual Larry

Great work sir 💐💐💐✌🏻 Gud one ,,, same here I m diesel mechanic from India Punjab

Check the alternator for draw. Had the same problem turned out to be the alternator.

Air hammers work great for races also avoids smashing fingers lol

Ah did you hurt your little thumb get the boss to kiss 😘 it lol 😂 ✌️

Hey Larry have a great day. 905am Monday October 5

🙌🙌🙌

The person who is reading this comment i wish you great success health love and happiness i am from morocco have a good life for everyone here God bless United States of America ^^💟🕇

Can’t really blame your boss for getting excited about getting some tools free once in awhile. He sure seems like he is always buying some tools for the shop/tractors and trailers plus all his other expenses.

Nice video , Where can I find this socket? What size is it? Thanks

Morning Larry as a fellow gear head neat video sure seems like the boss should invest in a press lots of uses for it and when he orders the press he can order that T-680 headlight trim😁 1.3 draw doesn't the the Obama electronic log draw when off? also the computer should have a hot at all times pin.🤔

I like your videos I was just wondering do you ever get tired of doing all that hard work for lazy drivers why are they there helping you I did anyway extremely informative and entertaining

I want to get that fee tool and whack you with it lol 😂 ✌️

GR8T FixEmUp ...and Teaching Vid....you'll find the draw don't worry ....

Hi Larry, can you give us the names of the tools you used and where to get them?

Hey Larry, sorry you adjusted that wheel bearing incorrectly. With the preset bearing that sleeve sets the proper clearance. Should just torque the nut to 250 and place the lock ring in. That sleeve crushes to set proper clearance. Good luck.

The wheel hub looked lightweight.Is it aluminum or white metal.Years ago that was heavy.

hydraulic press is good to have

Curious to how much and what kind of oil in Bearing hub..

The boss is lucky he has you. Hope you can open your own shop. What does ADL stand for

If that’s a ConMet system you are well under the minimum torque that they spec.

Maybe the black pony should be your's and give Big Blue a little rest. I'm sure Johnny Chicken wouldn't mind, especially if you put those train horns on it.

Hey

You need some light looks rather dark

Why wouldn’t u apply Greece like A car and pack it.

It’s wrong, if’s a preset hub, its having a cone inside between the bearings, wtf 😡it’s 300 psi torque, no backing off, it’s a preset hub, it’s not old style man … Unbelievable, the shaking is from the lose bearings 🤯🤯🤯🫢🫢🫢