Thanks. I like throwing in animation now in then. Makes it more fun!

Thank you very much!! I appreciate that.

Thank you very much.

😊 thank you. 😁

Thank you Nicolas! I am glad that my passion comes thru and that others can enjoy it as well. I really do appreciate that you give me feedback on these videos. Thank you again.

@@digitrc with pleasure 😉

You're right. You might consider watching my channel too

@@Rcheavyequipment one day I will add a track loader like your 634 to my fleet. I really like those.

Thank you very much. 👍

Thank you very much. I’m glad you let me know that you enjoyed it.

Nice. I really like Rc4wd lowboy. It’s a beautiful trailer. The only reason I didn’t get one is because it was not available at the time. I found the one I currently have and I really liked how wide it was. Plus I was worried about the clearance and it getting hung up. But for Highway hauling that thing would be fantastic. So might get one in the future. Let me know your opinion on that low boy.

@@digitrc your trailer is nice also, the rc4wd tailer is pretty wide as well. the zetros will set on it with no overhang. The Zetros is a bigger rig than the reg 1/14 tamiyas etc. So when you hook up the rc4wd trailer iss a nice height. I did design a different king pin a bit shorter as it now fits flush with zetros 5th wheel. As for back axles of trailer I am thinking about doing a slight lift to even out the height of stance. 4/5mm.. Im in the middle of huge kitchen remodel Im doing, so when I got the time I will show more on the trucks progress of makeover and trailer. My hg 802 and tailer are a great set up yet I was trying to experiment with weights of trailers etc.. Man that hg trailer is a beast..

@@thatsmyrc have fun with that kitchen remodel. Look forward to seeing your stuff in action.

You're right. Nice vid absolutely. You might try watching my channel too if you like heavy equipment

@@Rcheavyequipment Yes I am sub to your channel and I do look at the videos

Thank you.

Thank you

Thank you.

It does take awhile but I think it’s kinda fun to throw those in now and then. Did you notice the laborer cleaning off the blade at around 43min? He’s had enough and drops then kicks the shovel. I thought it was pretty funny. I’m going to check out that link you sent too. I love to detail my models. I’ve done some detail work to the Volvo and hopefully have it up in a video soon. Thanks for your feedback too.

@@digitrc ha ha really il finish the video now and get back to you.

Ha ha nice Dozing brother and camera location. Can I give you a tip. When reversing the dozer take it right back to level ground you want to tie in to , drop the blade set it and leave it , and go full throttle . Depending on the surface you will only have to focus on the tilt action. Sides to side. And another tip Dozers allways go on forward on the floats low loader, , blade right up to the goose neck for weight on the prime mover. For traction.

@@digitrc ha ha my goodness yes that is fanatic bro, ha ha the labourer shoveling the blade ha ha , priceless

I put them on one stick so I can operate the blade on the other stick.

I get a good hour run time on a 3s 5000mah battery! That’s petty good.

I didn’t change out the battery on it for this video. I run my batteries down to 3.6 to 3.5v a cell so 10.5v min on the battery pack. I also have my radio programmed so that the pump motor runs on demand when making blade adjustments so that saves a little juice.

The most likely damaged parts would be the motors as they are brushed 55t motors and maybe the ESC’s. (Two of each). The receiver should be fine. That should be all that would get fried.

@@digitrc yeah about my track loader is dead l😂l the track loader comes with red head conncter my battery 3s But the head is XT60 i make wire T-Pluge 4 between them looks like i flipped the head when i put that happen smoke and the track red head cut of and fly l😂l But i tested the reciever its work about the ESC i heard it emits 3 tones like this TET TET TET so bro do you think.i just to change the ESC only or some parts until back her to work again

@@The-Warm-voice1359 since you didn’t apply voltage to your motor’s they are probably good. I would start with the esc’s.

How are your batteries? Any damage to them?

@@digitrc i agree But i'm worred about hydraulic pump motor

@@fiskrond9212 that’s a tough one for sure. Do you have an excavator already or is the 360L your first excavator?

@@digitrc never owned an rc of any kind let alone a hydraulic 360. Looking at 4200xl as I'm not interested so much in the detail (mirrors, cab, etc) but the entry level operation (and anticipated repair at some point).. the better stuff will come later 🙂

@@fiskrond9212 4200xl is a good entry level machine for the price. You can always modify it like I have mine to make it what you want also. The dozer it’s so much fun! If all you have is a bunch of dirt to push around then the dozer would be my first choice. If you have a dump truck to fill and move dirt then an excavator would top the list.

@@digitrc and that is exactly my dilemma.. got lots of dirt to push.. but i want a 360.. am fascinated by the arm.. fixated with arm since gas mains replaced with JCBs all around my area when I was really young. Back in the days (70's) when you could get really up close to observe as long as you behaved yerself.. happy days! 🙂 ..and then came the Hy-Macs!!!

@@digitrc I've got say a level-ish 3x5m of vegetation (say upto 50cm tall.. nothing woody.. just weeds )to be cleared.. there will be burn piles! 😀

Check it out on rc4wd.com.