TTE710/810 Turbo DIY Install | Audi S4 B9 Stage 3

TTE710/810 Turbo DIY Install | Audi S4 B9 Stage 3 | Hybrid Turbo Upgrade

Рет қаралды 14,323

Күн бұрын

This step-by-step DIY installation of the TTE710 hybrid turbo will show you how I transformed my 2018 Audi B9 S4 into an absolute monster. If you're considering a hybrid turbo, especially The Turbo Engineers TTE810 or 710, you should check out 034Motorsport's Dynamic+ Stage 3 ECU/TCU tuning. The power output and drivability of the car is absolutely fantastic, switch to E85 and it's a rocket ship. I will also show you an upper and lower PCV hose service. The lower PCV hose does require removal of the turbo, so this is an opportune time to swap it out. You will likely need other supporting mods to install this turbo, make a plan with your tuner!
TTE 710 Turbo - bit.ly/tte710turbo
TTE 810 Turbo - bit.ly/tte810turbo
TTE 4-Bar MAP Sensors - bit.ly/4barmapforb9
034 B9/B9.5 Dynamic+ Tuning - bit.ly/034DynamicEA839
034 SuperDuper Inlet - bit.ly/superduberb9
Funk B9 Turbo Blanket - bit.ly/funkb9blanket
Liqui Moly Pro-Line Additive - bit.ly/prolineadditive
Turbo Manifold Clamp 059253139D - bit.ly/b9turboclamp
Turbo to Manifold Gasket 059253232C - bit.ly/b9turboclampgskt
Manifold Exhaust Gasket 06M253039G (2x) - bit.ly/b9turbomanigskt
Turbo to Catalyst Gasket 8W0253115G - bit.ly/b9turbocatgskt
M6x18 Torx Bolt N10196103 (4x) - bit.ly/m6x18
M6x12 Torx Bolt N10335206 (4x) - bit.ly/m6x12
Turbo Line Green O-Ring WHT007689 (3x) - bit.ly/b9turbooring
Lower PCV Hose 06M103217DD - bit.ly/b9pcvhose1
Upper PCV Hose 06M129041 - bit.ly/b9pcvhose2
Thermo-Tec 3' Heat Shield - amzn.to/3MQF6lF
Capri Tools Stubby Triple Square Bits - amzn.to/3E2OL3N
GEARWRENCH Half Moon Wrench Set - amzn.to/42cvpCE
Sunex 9726 Mini Ratchet & Bits - amzn.to/3m1V5CX
VIM Tools Half-Cut Torx Bits - amzn.to/3MvbQ2j
AEJ Metric Hex/Allen Bit Set - amzn.to/3MgIC8P
Low Profile Offset Torx Drivers - amzn.to/4159bSR
TEKTON 3/8" x 7/8" Offset O2 Socket - amzn.to/3MHkwV8
TEKTON Angled Tip Pry Bars - amzn.to/43x0na8
As an Amazon Associate and ECS Tuning Affiliate I earn from qualifying purchases. You don't have to purchase the specific items I'm linking to in order to help the channel at no added cost to you!
00:00 Introduction
00:14 Intake Air Box Removal
01:00 Turbo O2 Sensor Removal
01:31 Turbo V-Band Removal
01:45 Loosen Wiring Harnesses
01:58 Upper PCV Hose Removal
02:29 Turbo Inlet Removal
02:46 Unplugging Lower PCV Hose From Turbo
03:06 Support DG
03:27 Disconnect Charge Pipe From Turbo Outlet
03:55 Disconnecting Turbo Oil & Coolant Lines
04:29 Wastegate Actuator Removal
04:47 Vaccum Line & Diverter Valve Disconnect
05:09 Stock Turbo Removal
06:31 Lower PCV Hose Replacement
07:15 Prepping The TTE 710 Turbo
08:53 4-Bar MAP Sensor Installation
09:51 Turbo Line O-Ring Replacement
10:15 TTE 710 Turbo Installation
11:45 Turbo V-Band Installation
12:28 Final Turbo Reassembly
13:32 Charge Pipe Turbo Outlet Connection
13:58 034 SuperDuper Inlet Installation
14:32 Lower PCV Hose to Inlet Connection
15:13 Upper PCV Hose Installation
15:22 Intake Air Box Installation
15:42 First Start & Drive TTE 710 Turbo
16:23 Final Thoughts
#theturboengineers #tte710 #034motorsport #hybridturbo #turbo

Пікірлер: 78

@DmitrysGarage Жыл бұрын

Sean from 034Motorsport had some great suggestions for this installation that he reckons might save 20+ minutes: - Unbolting the charge pipe from the intake manifold on bank 1. - Unbolting the charge pipe from the bank 2 head (under Throttle Body). - Remove the exhaust studs off the head. With the studs removed, you don't need to loosen the 4 nuts underneath you can just wiggle the turbo out. - If you clamp the connection on the firewall behind bank 2, no water is lost. Really appreciate the tips Sean!

@callmecue Жыл бұрын

Thanks for the detailed DIY. Audi fan here. Also, you have to be the only youtuber that says the name of the company correctly: ZERO THREE FOUR! Not "Oh 3 4" 😁

@DmitrysGarage Жыл бұрын

Thanks! I did use to say oh-3-4 haha, but I was informed that was incorrect 🙂!

@Kiss__Kiss Жыл бұрын

Crazy Mod. Yeah that install is gnarly, Dmitry. But well worth it by the commentary during the pulls lol. Definitely looking forward to the, "From start, to now" type of video, in terms of mods.

@DmitrysGarage Жыл бұрын

Honestly it's not a bad one to do, there are a lot of little bits and some annoyances, but as far as turbo "kits" (this is really not even a kit) go you can't do much easier on a modern vehicle. The actual turbo install is a job someone experienced can do in a few hours and a first time installer can handle in a weekend being patient and careful. I'm very impressed by what this platform can offer given a fairly modest time investment in building, cost is another issue of course haha.

@swagcandi4069 9 ай бұрын

I also have a tango red b9 s4! No 710 yet, still enjoying 034 stage 2 on 93 :) Love the build.

@DmitrysGarage 9 ай бұрын

Thanks! Stage 2 034 is quite a bit of fun too :-). Tango red is probably one of the best colors on these IMO.

@BenzORama 8 ай бұрын

Excellent content, as always. What would be the approximate book-hours if a shop was doing this?

@DigitalCowboy87 Жыл бұрын

Congrats on this. I was in a similar boat with my 2018 where I went stage 3 but was on the 710 instead of the 810 because 034 wasn't quite ready to release everything for the 810. I now have the full stage 3 / 810 setup on my 2021 B9.5 and while there is a noticeable difference, it's not like you're missing out on a ton of power with the 710. If you haven't yet definitely get some e85 in that thing and enjoy that, it's the way to go! Sweet ride and enjoy the car man!

@DmitrysGarage Жыл бұрын

Thank you! I'm definitely on E85 :), was thinking about testing out the race gas tune too since I have drums of 260 GT Plus. I think the 810 is probably the best option at the moment, but I'm not ready to ditch the 710 to chase a slight optimization. I think I'll wait for more full frame support at this point. Either way I'm daily driving a 10 second and sub 3s 0-60 car, not much to complain about =].

@DigitalCowboy87 Жыл бұрын

@@DmitrysGarage Definitely nothing to complain about and it's so much fun driving a car that surprises everyone. Any friends and family that have taken a ride in either of my stage 3 cars have all been blown away, they can't believe how effortlessly fast the car is, and that the motor and transmission are stock lol.

@DmitrysGarage Жыл бұрын

@@DigitalCowboy87 Yep, I've let a few people experience a hard launch and its always a good time =)

@parisbrown4606 10 ай бұрын

@@DigitalCowboy87 Have you gotten any 1/4 times on your 810 vs 710?

@DigitalCowboy87 10 ай бұрын

@@parisbrown4606 unfortunately not, haven’t been to the track with either car. I’m right at sea level so I’d expect a low 10 second pass with sticky tires 👌🏻

@CHRIS-qm7ke Жыл бұрын

Great video! It's a nice addition to the other b9 hybrid turbo install videos out there as a reference when I install my 810. Did the turbo come with the lower pcv line that u replaced or is that an extra purchase?

@DmitrysGarage Жыл бұрын

Thanks for the kind words. The turbo does not come with the lower PCV line, but I highly recommend snagging one. There is a link in the description. It's worth replacing it while the turbo is out because the upgraded model has a little bit of heat shielding and more can be added. That the turbo gets immensely hot.

@PavelPenariu 10 ай бұрын

Thanks for the video ! Very helpful. How long did it take to do the whole swap ?

@DmitrysGarage 10 ай бұрын

For just swapping the turbo i spent a couple of hours with filming time. Some experienced techs say they can do it under 1 hour. If you’re considering it, check out the pinned comment. Sean from 034 gave some killer time saving tips which I posted.

@jamiestone9572 Жыл бұрын

Great video! Let me borrow that old stock turbo 😂 I think my turbo just failed

@DmitrysGarage Жыл бұрын

Aww man that sucks :). Hopefully it’ll be easier to swap with the video. Check out the suggestions from Sean @ 034 that I pinned. They should save even more time.

@MrModz1999 Жыл бұрын

Excellent video. Installing the TTE710 soon and am curious why you recommend more replacement parts than 034? I ordered their Turbo Installation Hardware Kit and it says in their description it’s all you need. Could you elaborate on that?

@DmitrysGarage Жыл бұрын

Thanks for watching! When I filmed this video that kit was not out yet. If their kit includes everything I listed (might have more!) then you’re good to go. I haven’t researched their kit in depth. 034 makes a good product so im sure their kit is killer. I just had to put together my own haha.

@MrModz1999 Жыл бұрын

@@DmitrysGarage totally agree! Was just curious as to why you recommend to replace more parts than they do. Just good practice?

@DmitrysGarage Жыл бұрын

@@MrModz1999 i suspect they’re targeting a set price point. Its not uncommon to assume users may re-use parts that still look good. For instance my o-rings probably would have held up if lubed and re-inserted, but while ur in there why not swap them? Same with the clamp and fasteners. People often value total cost over potentially having to re-do work later. I remember when I didnt have my own shop like this, I used to always remind my mechanic to swap all those extras. Like hey we already have the heads off. Lets replace all the valve seals and springs… i don’t want to do that later again…

@gmachine10 Жыл бұрын

Hey Dmitry. Did the new gaskets come with the new turbo? Or you needed to buy them all separate. I bought the 810 and it’s on route. So I want to make sure I have everything ready when it gets here. Thanks.

@DmitrysGarage Жыл бұрын

Hey Greg, unless you bought a kit, you’re going to need those extras. Otherwise the turbo is just the turbo.

@darrinscoilsclouds1498 8 ай бұрын

Would you recommend a pcv delete?

@MatthewJay80 5 ай бұрын

Thanks for sharing the installation! What is the wheel horsepower output of this on 93 octane?

@DmitrysGarage 5 ай бұрын

Im not sure on 93, haven’t tried, been on e85 only.

@btbd2785 Жыл бұрын

You know instead of using a larger intercooler for cooling the air, why not make or develop an air-conditioner" assisted intercooler or "mini refrigerator" for cooling of the air for the turbocharger?? Saves on space and probably more efficient overall??

@DmitrysGarage Жыл бұрын

Thats been done in the past. The Dodge Demon actually does this. It used to be kind of a pipe dream like electric superchargers and never worked well, but both are becoming a thing. One challenge is having to run the AC system of course to make the cooling and complexity vs a simple air to air intercooler. It makes more sense on something like the demon that has a top mount supercharger and no factory front mount cooler, instead it has a water to air one right on top of the engine. The AC there really helps by chilling the water itself.

@MeLL1211 8 ай бұрын

Hey, what’s your opinion about the rocker arm failure? Any problems ?

@DmitrysGarage 8 ай бұрын

Seems pretty isolated, so I'm not worried about mine yet.

@packat78 Жыл бұрын

deciding between 710/810. how's city driving with the 710?? still enjoyable with sprited driving, or too much lag for around town?

@DmitrysGarage Жыл бұрын

There is really very little change in lag with the 710. I believe the 810 does bump the lag a little more, but its still surprisingly low rpm. These are twin scroll setups and the turbos are pretty efficiently sized for the performance targets. Its really not at all like throwing a big turbo kit on a 4-banger or a massively huge single turbo on an inline 6 or days past. I just spent an entire week driving downtown for an event i was attending and the car hustled through heavy traffic no problem.

@DigitalCowboy87 Жыл бұрын

If you have the choice definitely go with the 810, I've had both and there's really no downside to going with the 810. It could be because my 2021 is newer and has less miles than my 2018 had but i actually get better fuel economy with the 810 vs what I did with the 710 on my 2018 lol. I also feel like there's more turbo noises and overall the 810 and all the supporting mods just feels like a better package. Good luck!

@packat78 Жыл бұрын

@@DigitalCowboy87 Yea, i dont feel like messing with new injectors. 710 likely more than enough power for daily driving

@DigitalCowboy87 Жыл бұрын

@@packat78 that’s fair! E85 and a 710 will put all sorts of smiles on your face haha :)

@macdaddy1234ism 3 ай бұрын

Where did you order your front r s grille from and rear spoiler ??

@DmitrysGarage 3 ай бұрын

You can find the grille on ebay/ali. The spoiler is had painted, its stock

@AdamPoirier-ui8kf Ай бұрын

I was wonder why you don't wrap cat ? Wrap you install will it cause turbo to crack?

@DmitrysGarage Ай бұрын

The stock cat and the aftermarket cat are already covered in heat shielding. Didn't appear necessary given that wrapping has some risks.

@MatthewJay80 5 ай бұрын

Can I bring my S5 to your shop for basic upgrades? I’m located in New Braunfels Texas

@DmitrysGarage 5 ай бұрын

Sorry, I don’t offer any automotive services here.

@coppinques7863 11 ай бұрын

did the pcv from the link in the description come with the heat shielding? i did not see it in the picture

@DmitrysGarage 11 ай бұрын

The new PCV has a small amount of heat shielding vs the original my car came with. I added more heat shielding myself since I have the hybrid turbo in there.

@coppinques7863 11 ай бұрын

@@DmitrysGarage is the pcv linked in the description up to date?

@DmitrysGarage 11 ай бұрын

Yea it was the latest when I did it.

@anthonymiranda3343 Жыл бұрын

Dont you need to prime the turbo since its new ?

@DmitrysGarage Жыл бұрын

I squirted in the bottle of the liqui moly pro-line additive, it’s specifically made for priming new turbos for a first start. There is not much oil capacity in there and it came with assembly oil in it, which actually made it kinda hard to squeeze the whole bottle in. Its a quick cut in the video but it took me like 10 minuted to slowly feed it in without overflowing. You can also inject some fresh oil with a syringe (without the needle) or turn the engine over with the fuel relays/fuses pulled if you’re extra paranoid, but as long as its not started dry it will be fine. The reality is oil pressure builds throughout the entire system almost instantly. So short of having bone dry bearings it will be fine.

@corycooper4955 Жыл бұрын

Let’s see those 1/4 mile times! How long would it have taken for install if you weren’t filming? Thanks

@DmitrysGarage Жыл бұрын

Soon! Without filming this job could be done within 2 hours given prior experience and the right tools. Give yourself at lest a day or a weekend if it is your first time or if you don’t have a fully stocked shop. Time for tool runs, research, etc..

@corycooper4955 Жыл бұрын

@@DmitrysGarage I’ll just drop it off at your shop 😂

@DmitrysGarage Жыл бұрын

Hahaha :) sadly im not insured for that. Sometimes i do work on friends card (with them) but Its a very clear policy that if you die because the car falls on you no suing is allowed haha. I should really draft a consent form.

@corycooper4955 Жыл бұрын

@@DmitrysGarage I’d sign it if I was close to you. I have 54k miles, so not sure if I’d want to add the turbo with that many miles. I love the car and could see having it a while or getting the B9.5 down the road. Only other things I’d consider would be SQ7, X5 M50i or Jeep Grand Cherokee SRT (way over priced though). I’ve loved all of our Audis though.

@DmitrysGarage Жыл бұрын

@@corycooper4955 id prolly pass on the 9.5. It’s basically the same car. The new one coming might be interesting though.

@parisbrown4606 11 ай бұрын

Out of curiosity what fuel were you running?

@DmitrysGarage 11 ай бұрын

I'm running E85.

@coreionjeffrey7925 9 ай бұрын

Any idea of the reliability with the 710?

@DmitrysGarage 9 ай бұрын

So far so good. Have not heard of many failures. Have heard of a couple of 810 failures recently though, like 3 in one week. Though nothing else major since then. As far as I know warranty from TTE covered the ones im aware or.

@packat78 2 ай бұрын

What file were you running in these clips?

@DmitrysGarage 2 ай бұрын

This was the E85 file.

@packat78 6 ай бұрын

Its the turbo blanket necessary in your opinion?

@DmitrysGarage 6 ай бұрын

I think it's a nice to have but not required, also you really wanna make sure you form it well with your hands (wear gloves!) once you heat it up, so it doesn't tangle up with the waste gate actuator. I just pushed mine down hard around the path of the rod and the blanket stuck that way once it cooled.

@packat78 6 ай бұрын

@@DmitrysGarage thanks. Just got a great deal on a slightly used 710. plan on installing this soon so just trying to put everything together.

@macdaddy1234ism 3 ай бұрын

How much did that all costs ?? You bro

@DmitrysGarage 3 ай бұрын

Retail cost im sure im over $20k in mods. Granted i do get some cost reductions with our sponsors.

@dimetime0 11 ай бұрын

Why does Audi make everything so difficult

@DmitrysGarage 11 ай бұрын

Honestly this is a pretty damn easy turbo swap. I know it seems like a lot, but compared to installing a normal turbo kit on most modern cars this is very easy.

@misterj5045 10 ай бұрын

You've never had your hands inside the bay of a Mercedes S600 😂. V12 Biturbo with just enough space to drop a socket.😂 The B5 S4 required removal of the engine to service the turbos.

@dimetime0 10 ай бұрын

@@DmitrysGarage I come from push rod LS engines so..

@richardkinzer7104 8 ай бұрын

wut this is a ton easier than the 2.7t get outta here lol