Thanks mate , very informative , looks well complicated , iv just recently bought my relay van and excited to get started

Grate vids keep them coming ..

THE TAD AND SMIDGE COMMENT EARNED YOU A SUBSCRIBER, LOVE THE BUILD ENJOY YOUR VAN.

Amazing ! You’re next level mate; thank you !

Really good video ❤, I’m about to fit some of these windows soon and this is very helpful 😊👋🙏🚐happy new year and hello from Australia 😊👋🙏🚐

Tad and smidge 😂 brilliant

windows fitted today thanks to your video for all the help, only thing i done different as im too impatient is i screwed the wooden frame to the van when i bonded it instead of clamping it and waiting, the screws were hidden by the window so all good and saved waiting hours on the frame bond drying :)

Also while i'm here the mysterious grey clips are not needed when installing the blind with a window. The blinds can also be used as stand alone blinds and if not fitted in conjunction with a Polyvision window they can sag in the centre, the clips are designed as supports to stop the sagging of the blind. When fitting with the Polyvision window the blind is supported by the window so no need for the clips.

Tidy instructions and good advice,and I am a tradesman great stuff. Maybe a face mask for the swarf. Well done very clear.

Brilliant video thanks :-)

Thank You to this advice.

Thanks for the video. I was hoping you would show us how to fit the inner frame with the blinds and fly screen :)

Hi, thank you for the very good videos with lots of instruction. Just a question : what is the purpose of the small metal bar that is positionned on the center of the upper face of the window? I am talking about the metal bar with 3 or 4 screws already installed when you bought the window? Thank you!

Great video, very informative and concise. I'm looking to install these windows in a vehicle body with thick walls (insulated @ circa 50mm +), do you think this is possible to bridge the gap between the timber and the internal trim and still make it look presentable? Many thanks.

Great vid! Pretty much following it to the word, thanks! Can I ask did the inside surround fit okay with the baton depth you selected?

Great informative video! i am trying to find out how much more width the blind frame adds on to the the window aperture. I'd really like to fit one of these windows in my vw t4 sliding door but not totally sure it will fit with the sliding door locking button being where it is. many thanks!

Very informative and useful video! Please could you tell me how long you left the soudal carbond to cure before continuing with fitting the window? Cheers

Really helpful warts and all approach. We have been trying to gather together all the items we need before making a start, and windows are still a problem. We particularly like the Solway Elegence ones, which are very similar to the Polyvision Aero. Did you consider these, as you have purchased other significant items from Solway?

Hi, thanks for the video, very informative. I'm a bit confused by the frame with blinds that comes with the window though as you didnt show it on your video, can I ask, does it fit over the wooden frame?

Loving the series and are umpteen deep, about to start ordering stuff now myself for the same van. I don’t suppose you remember what size windows you used in the rear and the sides please?🙏🏼

Hi there, thanks for the great video, currently building a Boxer and thinking about using these windows, could you please advise which size windows that you used ?

loving these videos im deciding on my windows and really like the look of them, unfortunately out of stock everywhere, could you tell me are they glass or plastic please

Great video, very informative! Just wondering how you lined the frame up on the outside? What reference points did you use to make sure the frame fitted properly inside?

Great video thanks - are the windows double glazed?

Do your corner pieces keep on falling off? Mine do lol ! They don't seem to fit very well at all. I think I will invest in some velcro to try to keep them in place. Great video as usual. Keep up the good work!

hi love the guide, what size windows did you fit. many thanks.

Can I ask what size that window is please?

Hi there! Great video! Do have or know of a video fitting the frame on the inside? 🤔

so you did the frame a few mm wider than the window and then you made the hole the same size of the frame is that right?

Hey, great video going to attempt mine tomorrow! What size screws did you use for attaching frame to window? Thanks in advance.

Hi, very informative video and series. Given that the door / body skin has a radius of 5000mm and these window frames are flat, I calculated the gap top and bottom should be approximately 7.5mm for an overall window frame height of 550mm. Which in theory might require quite a thick bead of sealer up to 8.5mm thick at the top and bottom of the window frame if you assume at least a 1mm thick bead of sealer between the window frame and door skin. Yet looking at your final result, you seem to have a reasonably even gap all around the frame to door skin. This can only lead me to assume the door skin and frame deflect to meet each other? Was the uneven gap noticeable prior to applying the sealer and bolting together? This has me agonising on whether to go for the Dometic S7P windows which appear to be the only windows with a 5m radius specifically for curved sides e.g. the Ducato, Boxer, Citroen etc. But they are more than double the price!

Point and a pencil is a compass. You have a pair of dividers!

Very informative thank you, are these 950mm x 450mm windows.

Hi, very useful and informative video. Could you tell me what size windows these were please? Thanks

Did you ever determine the purpose of the cream plastic pieces? I have two also I’m not sure what to do with 😅

Please could I ask what size polyvision windows you used for the Relay on side and barn doors.. Thanks

Hello, A fitter warned us off these for our Sprinter due to vibration and leaks. What’s your experience after 2 years please?

Nice vid, I am considering the same windows in my boxer van, what size did you use for the sliding door plz? Are you happy with your choice? Thanks in advance. P.s. cracking work

Hi, this is Lee Carter from Magnum Motorhomes. We are new to youtube however thought i would comment on the great video and ask if we could possibly link the video to our website to help others when it comes to installing?

Could I ask what thickness of wood you used and (particularly) the “odd” Solway panel where you’ve add the trim on a later video please?

What size battons did you use for the frame

This is my job today! May seem like a daft question but where do you take the ‘cutout’ dimension from? Is it the same as the size of the window ordered? Can’t find this info from the (rather poor) Instructions!

Hi, great video! Please can you tell me the size of the windows in the back and the size of the windows on the side. Thanks

Where did you get your van from and how much

Look like a good option but quite costly compared to the nirmal bubble type windows

Interesting I wonder what one large window costs

What size windows have you used in the sides and back doors ??

Are these double glazed windows

Ha Ha. I always measure everything within a tad and a smidge.

Great informative video.. love it and have done my van windows easily thanks to your efforts.. But for goodness sake drop the brain dead mind bending whistling !!!

Switch off the background music.

Constructive criticism music makes it hard to hear what your saying and unnecessary

£400+ and no fitting instructions unbeliverble take us for mugs