Unboxing & Building: Pedaltrain Nano+ Pedalboard

Рет қаралды 29,861

5 жыл бұрын

Today we Unbox & Build the Pedaltrain Nano+ Pedalboard. Let me know in the comments below what types of Pedalboards & Builds you use.
Guitar Center:
www.guitarcenter.com/
Pedaltrain Nano+:
www.guitarcenter.com/Pedaltra...
Pedaltrain:
pedaltrain.com/

Пікірлер: 30

@ManuelLopez-ff1op 2 жыл бұрын

Many thanks for the demo! Very apreciated!

@johnl.6930 2 жыл бұрын

Thanks! We’ll done. Very helpful.

@personel02 3 жыл бұрын

I am about to build my pedalboard on top of pedaltrain nano+, thank you for sharing this video!

@KATRKATR 4 жыл бұрын

Very clean man! I also only have 3 pedals and I will be looking to get this board! Nice video!

@stopitrightnow12 5 ай бұрын

Very nice, I've been eyeing the Pedaltrain Nano for a while. I only use 4 pedals total so I feel like it would be the perfect size for me. Not to mention how much bang-for-your-buck the Pedalpower X4 powersupply is!

@JB19504 2 жыл бұрын

Great video. Now I know what I need!. Except I think I might need room for like 2 more pedals.

@corbettsmith7285 2 жыл бұрын

Guitars and dirt bikes bro? I think we’re best friends

@miklaop 2 жыл бұрын

Thank you! Now I know about mxr dc brick!

@toddtech404 4 жыл бұрын

I have that same pedal board for my boss katana light weight setup. The amp has decent efx and is light at 26 pound (50 watt one 12") so on my micro board I use a nux channel changer that gives me 4 channels, a e.q. for lead boost or fast tonal adjustments, a tuner, and a baby crybaby. I like the light weight and one trip for load in load out. Besides the days of having to have a full or half stack are done as more venues have nice p.a. systems and mic'ing cabs.

@jazzguitarwithandy 4 жыл бұрын

I like how your dining room has become a gear room! Where do you eat?! I’m looking at this nano plus for the same reasons. Nice demo man.

@Weavius 4 жыл бұрын

My dining room is my music room too. 😉

@radiowalker88 3 жыл бұрын

Nice video. How can I attach my Pedal Power X4 to the same pedalboard? Is it enough with velcro? Thanks in advance.

@guillermodelblakeyo2019 2 жыл бұрын

Does the power supply genuinely fit underneath, or is it taller than the board a bit? It didn’t seem thinner than the board, or at least flush with it.

@markhall3323 4 жыл бұрын

I could never allow those patch cables to hang over the front edge of the board

@MrBagel97 4 жыл бұрын

Does the mxr make contact with the floor or do you have a small amount of clearance?

@m32ramsey 3 жыл бұрын

There is a small amount of clearance & I have hard wood floors so, no contact. If you have carpet then yes it will touch but, honestly it barely even gets warm.

@victorhenrry6102 4 жыл бұрын

I made my pedal board but it's to big and have tc electronic cinder overdrive , chorus afterglow, echobrain and skysurfer reverb and sound nice!!!!!!!!!

@SynZ777 4 жыл бұрын

Why didn't you put your power supply perpendicular so you have access to all 8 inputs?

@m32ramsey 4 жыл бұрын

I only needed access to 3 of the 9volt outputs, also mounting it this way gives you more contact surface for the Velcro. It’s all personal preference.

@Fadedglory14081 2 жыл бұрын

Would the power supply fit if you rotated it? Less surface area for Velcro, but does it physically fit mounting is vertically giving access to all 8?

@lukeseto9848 4 жыл бұрын

Nice! How much clearance do you get with the MXR PSU?

@m32ramsey 3 жыл бұрын

There is a small amount of clearance & I have hard wood floors so, no contact. If you have carpet then yes it will touch but, honestly it barely even gets warm.