Changes the whole look of the Samurai, pretty cool!

I just bought an 88 Samurai. I really appreciate your content. You’re awesome! Thank you.

👏 good job! Most definitely will need too refer to video agin when my lights arrive, thanks!

Thanks for showing the harness kit install. I put a DIY light harness with relays on my baja. The kit looked so much easier! - I really liked the lights too. My baja has a similar setup with DRI's/turns, but your lights look 10 times better. Thanks for the links!

Thanks so much, just got given a set of led lights and this makes it so much easier. Legend 👌

That looks AWESOME!

Great video! Wired my LEDs on my ‘86 Samurai in no time! Thanks.

Awesome step by step conversion video.

Thanks so much!

You are really creative .. I wish you good luck

Looks great, bro! Keep up the good work. Any update on what your gonna do with the burb?

I see this from Chile, the modifications you make to the Suzuki samurai are incredible!!!

The led lights are positively switch hed lights and the original head lights are negatively switched. That's the need for the new wiring diagram

Very nice set up

Bought the harness from Amazon you listed but there are NO additional red and yellow wires at the orange plugs like you show in the video???? How do I wire up the DRL and amber turn lights? Do they make that exact harness you show in the video?

Lights look really good. Great video but no solder on the wires? Heat shrink isn't going to hold the connections together long term

Great video, I had no idea that the scissor jack is under the hood.

Wanting to know the process on wiring up the amber light with the turn signal wire

Give these a go for your connections ( no affiliation) "Heat Shrink Solder Sleeve Crimpless Butt Connector". Why are you converting to propane?

Nice job bro..much appreciated! I'm about to undertake the LED swap on my '94 EFI Sammy. In your link to the new harness on Amazon...their harness doesn't seem to have the 2 xtra wires for the DRL etc. Looked every where...any suggestions? THANKS mate!

Which wire (color) do I tap into for the parking lights on the aftermarket head lights?

Good work on your Sammi... looking under your hood here it looks like you're missing a lot if your emissions equipment? How is that working out for registration? I'm not too far from you in CA and I can't get mine to pass smog and I DON'T want to go green sticker...

Is there an easy way to align them? My samu is super tall because of the tires and every time I turn the light on I get everyone blind

Can someone put up the link so i can make the purchase from amazon also the harness thanks

Would love to see how they perform on the road looking to get a pair for my rig

Where did u wire the dlr to.

What did you do about the hyper flash with the turn signal?

Hola buenas me puedes mandar el circuito de conexión de los reles porfa

Always solder the splice.

Is there a guarantee on Uni-Shine products?

What wire harness is that it will not pull up anymore.

where can i get that same harness?

A useful video only spoiled by one thing! Mate, you need to learn to solder!! Twisting wires together and then hoping they stay together using shrink wrap tubing is not a permanent solution! Given that our trucks are now 30-40 years old the wiring loom isn't in the greatest of shape anyway! Bare the wire, then clean the end with a scotchbrite or wire wool, then wipe with 'Panel Wipe' or a similar high flash solvent to remove any finger grease etc. Using a small soldering iron 'tin' each bared end and then solder together - then slide the shrink wrap up the wire (you did remember to put some on didn't you??) and heat using the gun - Job done and a good, solid and more importantly conductive wiring joint! BTW the reason you should use an aftermarket wiring look for running LED lights etc is simply because the switching on SJ's etc is done on the negative side of the light unit, i.e the light always has power to it, and it comes on when the earth connection is made. The loom should be specified: for vehicles with negative switching.

SORRY........What an idiot I am!!! Watched the video again and saw that the red and yellow are on the LIGHTS and not the harness. Thank God for your video so nuts like me can get it done!

Im converting a 86 tin top to led....

Link to the LED lights are now to a different design.......

i borrowed power from right here. really? what is "right here"? waste of time

Hi Boys 😍💋 💝💖♥️❤️