If you haven't seen part 1 see it here: • Rough Country-4 Inch L...
Пікірлер: 117
@SnakeRiverFishing6 жыл бұрын
A pitman arm puller is the way to go get on loan from autozone or take the box down to a shop and the steering box out of the truck and in a vice to do it is best plus huge caution using a torch to heat the arm up you can melt the seal on the worm shaft easily ruining the box and a bunch of pounding and prying is not recommended either great video
@truepompey9 жыл бұрын
Looks sick man. Great build
@UpNorthOutdoors9 жыл бұрын
Pompey-Wolf Thanks man!
@kraigy283 жыл бұрын
I’ve got three of my bracket nuts just spinning. 🙄 1995 f250 7.3. Same lift kit. Gonna have to cut the bolts and figure something else out for those three that I have to cut.
@Kanglar7 жыл бұрын
Looks like it turned out to be more like an 7 or 8 inch lift. Put a 4 inch lift (supposed to be) on my 91 F250, measured before and after and it turned out to be 5.5 inches of lift. Make sure that front brake line isn't stretched too far
@pmorris357 жыл бұрын
just for future reference if you need to remove the pitman arm on a truck like this they have a pitman are puller other than that great job man i put a 6" on my 96 150 with 33s if you go 35s you will need to change gears in both axles
@UpNorthOutdoors7 жыл бұрын
pmorris35 I'm running 35's right now. The 4.10 gears handle them like a charm
@Dusty715_8 жыл бұрын
Yeah I put headers and dual exhaust on my 1983 chevy Scottsdale k20 with a 350 and turbo mufflers and it sounds good
@UpNorthOutdoors8 жыл бұрын
Noice
@SWMP15237 жыл бұрын
That's pretty badass man, I'm lookin to do this to my 2000 ford ranger soon
@space.cowboy699 жыл бұрын
nice build bro, she sat a lot higher than i thought with that 4", ill have to keep that in mind. ive been looking at rough country. i just dont have the proper tools for an install. anyways, i like the truck. i usually dont like fords but 90s are really nice
@UpNorthOutdoors9 жыл бұрын
Hey thanks man! The front springs do break in so it gets a tad bit lower, but yeah it was a lot higher than I expected to
@countryboylife5darlowe3916 жыл бұрын
Thanks for the video. Great job on the lift kit.
@seanhynes2328 Жыл бұрын
can you please tell me what kit this is
@UpNorthOutdoors Жыл бұрын
It’s in the title haha. 4” rough country lift kit for 96 F-250
@drewcarlson57569 жыл бұрын
Nice build
@Dusty715_8 жыл бұрын
and I would suggest stainless steel pipes because it sounds better and looks good hope you put a video up on the headers and pipes
@UpNorthOutdoors8 жыл бұрын
Yeah I will when I get the money haha
@badass96114 жыл бұрын
Where is the sway bar in the front and back I got the same truck and I got a sway bar in the front
@MichaelSanchez-ci6vn5 жыл бұрын
Looks pretty safe under there 🤣
@roberttrx-75053 жыл бұрын
How the fuck did you get the bolts on the bottom of the cross member
@cadezimmerman18625 жыл бұрын
Got the same truck and I'm thinking about getting that lift, but I am concerned the truck will feel gutless with 35s... when you put 35s on it, did you re-gear it or is it just fine?
@Bigpeepee754 жыл бұрын
It doesn’t look like you have a solid front axle, were you able to adjust the camber so the front tires are straight up and down?
@kayotic148 жыл бұрын
Hey how many hours or days did it take you I want to do a 4in RC on my 1990 ford bronco
@Clydedoesit2 жыл бұрын
No front sway bar?
@tjrichardson87564 жыл бұрын
That must be a common problem with the steering cause my steering wheel is off by that same amount
@calebbeer17399 жыл бұрын
Do you have to install the leaf springs with the lift or is that optional???
@abelcastellanoss19727 жыл бұрын
the Shock Absorbers is upsidedown
@UpNorthOutdoors7 жыл бұрын
Abel Castellanoss yeah I know I ended up switching em around lol
@zipptardnim9 жыл бұрын
Nice! Lookin good
@UpNorthOutdoors9 жыл бұрын
Thanks!
@parkerleffew53119 жыл бұрын
Did your front shocks that came with the lift, did they have loops on both ends of the shock like the rear ones or did the have a loop on one end and a shaft on the other?
@UpNorthOutdoors9 жыл бұрын
Parker Leffew Hold on lemme go check!
@hammerhead19able8 жыл бұрын
Nice Truck! I just recently got a 1997 f250 4x4 heavy duty truck. I am think of lifting the truck. All I have ever own has been Chevy trucks. I am excited. Thinking of a 6" lift kit. Your 4" seems to sit just about right. Now, what size tires are on your truck or have you put them on your truck already?
@UpNorthOutdoors8 жыл бұрын
+Thor Hamm I put 35's on you can see on some of my other videos. But with my new bumper I could easily fit 38's
@ryanyates36188 жыл бұрын
+UpNorthOutdoors you don't need control arms or sway bars???
@UpNorthOutdoors8 жыл бұрын
+Ryan Yates nope
@andygray83577 жыл бұрын
Does anyone know how to get a wrench or anything on the top slit of the middle axle brackets ? The little slot above the coolent line to hold the top 2 bolts on the axle bracket by the oil pan
@cameronfonner31144 жыл бұрын
I have the same problem!
@datboipreston23977 жыл бұрын
would this be the same on a 1994 ford f250 7.3
@ethanmaaske55609 жыл бұрын
what part of mn u from? im in mn too. i gotta 93 f150 xlt and a 64 chevy c30. lowered the c30 and bout to lift the f150! anyways, nice work man!
@nickm27577 жыл бұрын
I'm looking to get the same lift did you have to put front and back sway extenders on your truck
@turkfebruary58366 жыл бұрын
Were the factory axle pivot brackets bolted in or riveted?
@brevinbeckler91018 жыл бұрын
+UpNorthOutdoors how is the ride is it rougher than before you put the loft on?
@UpNorthOutdoors8 жыл бұрын
Yeah It's a little rougher but not bad
@BenJamin-ou7kd4 жыл бұрын
Stock ride is really rough , how does this lift improve or worsen the ride quality?
@alexh43169 жыл бұрын
I have a 93 f-250 xlt single cab same bed Same motor do you think it be almost identical to what you have to do and around how much you think it would cost?
@UpNorthOutdoors9 жыл бұрын
Bob Emu Yes the lift kit is identical it is for f250's from '87-'98. The lift kit is $610 plus if you want a steering stabilizer it'll cost you some more.
@kurtreed82396 жыл бұрын
how did you do your front sway bar? it doesn't look like you have one?
@pinnaclecooking23848 жыл бұрын
I'll be buying this kit for my 97 f350 long bed 4x4 7.3 next week. did you need to get intended brake lines? and how long did it take you to do?.i already have 35's on it
@UpNorthOutdoors8 жыл бұрын
Nope didn't need to extend anything. About 1/2-1 day
@seancarrick15296 жыл бұрын
Did the 35’s rub without the lift kit?
@eucsstamticc8 жыл бұрын
What size tires did you end up running on the truck? Any rub? Turning issues?
@UpNorthOutdoors8 жыл бұрын
35's. Rub a bit if I crank it
@jenlulu50765 жыл бұрын
Did you keep your stock sway bar linkage
@Desertdiesel4 жыл бұрын
Hey how did you get your axle brackets off?
@joesitler14749 жыл бұрын
Hey did you have to extend brake lines or driveshafts in anyway? I wanna do a 4" on my 95 f250
@chrismoser46898 жыл бұрын
What is the front spring arc with weight? I built my own pack and would like to check it.
@UpNorthOutdoors8 жыл бұрын
+Chris Moser I can check in a little bit for ya. But they settled over time so it varies a little bit
@chrismoser46898 жыл бұрын
That would be great I just need to be close. A measurement from a strait edge between the two spring mounting bolts and the top of the axle it would help a lot.
@KS-vd2qx6 жыл бұрын
Where did you get the front extended brake lines?
@kayotic148 жыл бұрын
And also on a 4inch lift should I extend my brake lines on my ford bronco
@UpNorthOutdoors8 жыл бұрын
I didn't have to extend anything but I don't know about a bronco...
@kayotic148 жыл бұрын
+UpNorthOutdoors I found out you don't my friend put a 6 inch and that's why I'm do a 6 inch for the bronco but thanks anyway keep the videos coming
@kayotic148 жыл бұрын
+UpNorthOutdoors hey I have a question can you email me I need help on putting the brackets for the ttb because it says to drill a hole but I'm kinda confused
@Prescott85928 жыл бұрын
Did you replace your pitman arm? Or was it the same one ?
@UpNorthOutdoors8 жыл бұрын
+Cody Prescott replaced it
@gotsomegetsome9 жыл бұрын
How rough is the ride with the new springs? Any better or worse than stock?
@UpNorthOutdoors9 жыл бұрын
gotsomegetsome I'd say there isn't really a big difference
@tanmelons8 жыл бұрын
did you need to extend any brake lines? or change anything else?
@UpNorthOutdoors8 жыл бұрын
No
@Taylormade2477 жыл бұрын
MustangMAN I had to purchase a brqhe line kit for mine, with the suspension flexing the stick ones were not long enough
@nathenwendinger74189 жыл бұрын
How long was the total install of this lift
@seanpaddock59478 жыл бұрын
Steering stabilizer?
@UpNorthOutdoors8 жыл бұрын
Yep I made a separate video on it
@TimTimm8308 жыл бұрын
did you have control arms where there front leaf spring goes?
@UpNorthOutdoors8 жыл бұрын
+tim esperanza nope
@TimTimm8308 жыл бұрын
UpNorthOutdoors I'm having trouble Which lift kit to get from rough country since I have the control arm in the front axle not the leaf springs
@UpNorthOutdoors8 жыл бұрын
tim esperanza Tbh I don't know. But if you message rough county on customer support they will usually get back to you within a day
@TimTimm8308 жыл бұрын
UpNorthOutdoors They have they just give me the one with the leaf springs but that's why I wanna do the straight axle swap
@UpNorthOutdoors8 жыл бұрын
I have basically finished my straight axle swap with a dana 60 (which is the axle that fits) and my old lift works perfect with it with the leaf springs
@DcBenderdoneright9 жыл бұрын
Do you have the dual I beam front axel?
@frostbite19918 жыл бұрын
+Mitchell Strain yes he does. You can get a good look of it at 1:00
@frostbite19918 жыл бұрын
Hows your front end holding up with that lift? Twin I beams dont like to be lifted much lol
@UpNorthOutdoors8 жыл бұрын
+Zac Price Holding up fine!
@frostbite19918 жыл бұрын
+UpNorthOutdoors good to hear. i have a 92 7.3 idi with the twin traction beam. was an old cement/gravel hauler so all the axles were upgraded. im torn between a 4 or 6" lift.
@UpNorthOutdoors8 жыл бұрын
I honestly think the 4" looks great and now that I made my new bumper I could easily fit 38" tires. But a 6" lift would be sick too!! The only reason I didn't do a 6" is that I would be getting pulled over alot here in mn for being to high
@frostbite19918 жыл бұрын
I'm in N Idaho. Just saw a newer power stroke lifted about 10" with 46's at the grocery store. Cops dont care here lol. I used to have a 92 f250 with a 351W crate motor lifted 6" with 35's. Rode like shit, and I bet it was a rough country lift, but it had a D60 up front and a sterling 55 full floater in the back. It was a beast but I could literally watch the fuel gauge sink at wot. I might look into a sas if I do decide to lift it big.
@UpNorthOutdoors8 жыл бұрын
+Zac Price Nice! I can watch my fuel gauge sink too lol
@Dusty715_8 жыл бұрын
if I were you I would put dual exhaust on it with race bullets or turbo mufflers
@UpNorthOutdoors8 жыл бұрын
I'm planning on doing dual exhaust once I do headers
@Ramirez45657 жыл бұрын
Sweet video brother! I've got an 83 f100 with an I6 300. Planning on doing a 4" lift on it as well. Sure wish I had one of those air jacks! 👍
@rhettgreen42058 жыл бұрын
Hey I just lifted my 1990 f250 and I have some new 35s I'm going to put on and I'm just wondering if you had a camber problem with the front wheels when you lifted your truck? If so how long did it take for the front end to settle down?
@UpNorthOutdoors8 жыл бұрын
+Rhett Green Yeah it cambered a bit. I would highly recommend getting a steering alignment because that helps with it alot. And yes my front end eventually settled down
@Blitzaviation8 жыл бұрын
how long did it take for you to install it total?
@UpNorthOutdoors8 жыл бұрын
A day
@Blitzaviation8 жыл бұрын
UpNorthOutdoors an entire day?
@UpNorthOutdoors8 жыл бұрын
Billy Litz Well I did it in 2 evenings
@wickedgto58356 жыл бұрын
what are thos boots
@UpNorthOutdoors6 жыл бұрын
winter boots lol. it gets cold in Minnesota
@jakelindy39399 жыл бұрын
Cutrently putting yhis lift on my 7.3 as we speak. Lot more crap in the way on this motor than that.
@UpNorthOutdoors9 жыл бұрын
Jake Lindy Haha good luck!
@fordguyaj55816 жыл бұрын
how did it turn out .. I got a 92 7.3 that I wanna put a 4" lift on but besides spring packs and a pitman arm what else did u need? traction bars? or other steering components all fit?
@BIAProductionz9 жыл бұрын
Do you have to install the leaf springs with the lift or is that optional?
@UpNorthOutdoors9 жыл бұрын
***** Yes, unless you want to have a 4inch lift in the back and nothing in the front lol
@BIAProductionz9 жыл бұрын
UpNorthOutdoors Haha thanks for the reply! I wanna get the same lift for my '94 F150 but it looks pretty difficult, especially since I'm not very good with mechanics.
@UpNorthOutdoors9 жыл бұрын
Haha its not to bad if you follow the directions! Otherwise you can probably pay a local mechanic put it in for you
@BIAProductionz9 жыл бұрын
UpNorthOutdoors Sorry to bug you so much, but this is my last question :D Did the kit come with instructions? I'm assuming it did but would just like to be sure! Thank you so much for all your help
@UpNorthOutdoors9 жыл бұрын
***** Yep it comes with instructions! If you have any more questions ask away I'd love to help!