No video

Uv resin issues

  Рет қаралды 60,130

Katie Gordon

Katie Gordon

Күн бұрын

This may happen to you and this is how I would fix it. Hope it may help someone
/ 589374758258571

Пікірлер: 187
@jenniegray985
@jenniegray985 3 жыл бұрын
I just watched another video and to avoid your piece from warping, hold the UV light high above your piece for the first few minutes and then slowly get closer. That will keep it from losing its shape.
@morbidgypsy
@morbidgypsy 2 жыл бұрын
I read that too. Slow the curing down a bit.
@adanvdousdi0922
@adanvdousdi0922 2 жыл бұрын
oh im going to try that. cuz mine warps too...
@chevynovascotia3301
@chevynovascotia3301 3 жыл бұрын
Omg I'm watching you with the blade and feeling the time I sliced through my thumb when mine slipped...ouch
@ElectroAnnie
@ElectroAnnie 3 жыл бұрын
Yeah, I was cringing the whole time. Especially with a dog nearby who could jump up at any time and whoops! I'm reminded of the time I slipped and cut my index finger. The entire tip of my finger was numb for 2yrs after that!
@deimantekazlauskaite5059
@deimantekazlauskaite5059 3 жыл бұрын
I'm having so much anxiety watching her use it, this is exactly how I sliced my thumb open 😰
@katiegordon610
@katiegordon610 3 жыл бұрын
I work on teeth all day when we clean teeth i use a blade that are way sharper than those blades plus I use a fulcrum w either my thumb or ring finger to guide my movement so if it slips im using pressure against that to make it so I dont go all crazy but totally do it the way that feels safe for you
@chevynovascotia3301
@chevynovascotia3301 3 жыл бұрын
@@katiegordon610 oh my
@LG-qv8rt
@LG-qv8rt Жыл бұрын
I have a blue nose that looks exactly like her acts exactly like her. And I have the same exact problems. I think all blue nose are just alike. I will be sitting down doing my resin‘s and my crafts, and she will come up to me and be nudging me and pushing me. When you turned your camera and showed her my jaw dropped and I busted out laughing so hard. Just because of Jackson I’m subscribing….😂
@sandcastle2069
@sandcastle2069 Жыл бұрын
Please by extremely cautious sanding resin. Inhaling the dust can cause serious respiratory problems. I am not allergic to anything. Always had great health, then suddenly I found myself in the back of an ambulance with sirens on with huge problems to breathe. At the hospital there were eight doctors, nurses and surgeons ready gloved up ready to save my life. It happens that people find just the right “stuff” that irritates the mucus lining in your lungs and respiratory tract and they instantly swell up leaving you with none, or a very tiny opening to breathe through. When that happens, your life is threatened and you are minutes away from dying. I am a tough girl, never been sickly or timid, and like all of you I thought these few seconds of sanding couldn’t possibly be harmful. I was hand sanding in a huge room as well, so how much could I really inhale? It turned out that only a few specks of dust was enough to almost kill me. So please, please be careful all of you. I know masks are horrible, but being dead isn’t cool either.
@neverlookback876
@neverlookback876 2 ай бұрын
I'm so glad you are ok. This sounds horrific. This post has changed all my plans today, I was about to start learning to resin, instead I am now going in to town for safety supplies first. ❤thank you x
@NinaHansen2008
@NinaHansen2008 Ай бұрын
Thank you for telling about the warping. I have had a number of resin things that warped!
@lisajarvis3820
@lisajarvis3820 4 жыл бұрын
Tip ~ place the warped resin in between two sheets of box cardboard and press in a book press overnight~ works brilliant!!
@CallowTenpa
@CallowTenpa 3 жыл бұрын
After its cured?
@hopelessnerd7810
@hopelessnerd7810 3 жыл бұрын
sera if it isnt cured its going to get everywhere. Plus the warping happens because of the curing so it needs to be fully cured.
@avaa2314
@avaa2314 3 жыл бұрын
@@hopelessnerd7810 yeah mine was dry on one side and the dry slightly tacky on the other side. Tacky side stuck and got ruined
@chevynovascotia3301
@chevynovascotia3301 3 жыл бұрын
Thank you so much for explaining the70% and 90% alcohol. I was using 90 and everything I had was cloudy
@createinspain
@createinspain 3 жыл бұрын
If you don't have a Dremel, you might still have an electric e File for nails. I have one in my craft room and love using it for this and many other things. I prefer it because it is lighter and I can hold it like a pen.
@pattiklaus9580
@pattiklaus9580 Жыл бұрын
Miss your crafting tutorials! Hope you are well!
@SephoraAddicted
@SephoraAddicted 2 жыл бұрын
Omg! Your dog is gorgeous! And I love your video, I have this overflow problem a lot. I'm a beginner resin crafter
@annegredler5364
@annegredler5364 4 жыл бұрын
I just found your channel and am enjoying your videos. I just recently purchased a Dremel to use with my polymer clay but since I have never used one before, I am totally uneducated and confused about what attachments (sanding, buffing, grinding, etc.) I should be using for various steps in finishing my pieces. There are some videos out there about Dremel but they aren’t directed towards polymer clay. Most I see are for wood and metal. I would love to see a video explaining what you should use for polymer clay and what they do, what speed you should use them with, and even where you can buy the various attachments. I have no idea what you would use the rubber tip for. I have no idea what kind of buffing wheels to use. You get the gist. I think a lot of people would appreciate an educational video like that. Thanks!
@katiegordon610
@katiegordon610 4 жыл бұрын
I show how I sand but not w the dremel in most of my videos before the Corona virus because uploading takes forever at my house I show buffing in alot of them as well but of course at the end when u would be buffing and all of that. The wheeles I have are on my Amazon account which the link is in the description since November start from polymer clay pendant one or two and work up I was very concerned w not leaving any steps out which is why my videos are so long. Now that I have 100 plus videos I do start to cut the parts out that I have shown a million times like the sanding and buffing. Try that first because alot of the questions u asked I have answered in quite a few videos just not a specific video on it
@sonjacobb6360
@sonjacobb6360 3 жыл бұрын
Awwww I have a pitty that loves loving n playing and bugging too... LOVE IT - LOVE THEM!!
@user-dn9vd9xg9p
@user-dn9vd9xg9p 2 ай бұрын
These are beautiful!
@persesrathert8324
@persesrathert8324 4 жыл бұрын
Those are beautiful pendants! Thank you for the tips.
@bigfoot8778
@bigfoot8778 5 жыл бұрын
I did buy the decorom resin too but have not used it for anything yet. Nice to know that it will warp flat peices. I very much like the finish you got with both resin peices. I also like the design you made.
@katiegordon610
@katiegordon610 5 жыл бұрын
It does but only very slightly for me st least. When I take it out of the light its slightly warm I take a clean tile and push down flat to help it flatten out some that seems to help. I've used this alot and sold alot w using it and no one but me has ever mentioned it so I think it's just us being picky it had a nice finish too. I love it's cheaper and cures so quickly
@EmbraceTheChakra
@EmbraceTheChakra Жыл бұрын
a tip to remove the lumpy bit, heat the knife with the bunsen burner, then scrape the resin
@rebeccaharden6018
@rebeccaharden6018 Жыл бұрын
I love the green one without the flowers the best
@larchmontbreeze7428
@larchmontbreeze7428 4 жыл бұрын
Those pendants are beautiful!
@dezcovarrubias7933
@dezcovarrubias7933 2 жыл бұрын
Thanks for the tips ! I have a little stinker who's always interrupting my work too
@craftylittlerthings
@craftylittlerthings 3 жыл бұрын
Thanks for the info, but you should be really careful the way you use that craft blade. I had a friend who lost the top of her finger using one the way you were, and as you are on video you are showing people to use a blade like you did. I'm not trying to be horrible just thinking of your safety Hugs x Ann x
@PalomaMartz
@PalomaMartz 3 жыл бұрын
I was thinking the same! I was freaking out by the way she was using the blade :| so scary
@katiegordon610
@katiegordon610 3 жыл бұрын
I works w scaples, suture needles, dental instruments that are so sharp they will slice your finger w the breafest touch. This dull ass craft knife literally I would have to be rubbing it back and forth on my finger to get it to cut I also have a fulcrum w my thumb if u didn't notice that is a thing we are taughtita important to stabilize w the thumb or ring finger most my pressure is being pulled w my thumb not pushing in w my other fingers it gives more control but remove how u want to if its not comfortable for u or like I know some people they are just accident prone and would hurt themselves doing the simplest things
@m.w.7661
@m.w.7661 3 жыл бұрын
It gave me anxiety too! I was cutting something with super dull scissors a few months ago and they slipped and ended up cutting through a major nerve in my finger. I was so surprised such a dull blade could do that! I learned my lesson, for sure!
@craftylittlerthings
@craftylittlerthings 3 жыл бұрын
@@katiegordon610 I’m also trained in using all you said apart from teeth, but things a lot worse than that, I’m an ex army nurse and I worked in an operating theatre, but I would still not show anyone me using a scalpel the way you did, Don’t get me wrong I enjoyed watching you, but I know a number of kids watch KZfaq craft channels, so you would be teaching them to use a blunt knife to cut. Their is a saying that goes ‘ a blunt knife causes more accidents and cuts the deepest in when an accident happens’
@frankcosta6592
@frankcosta6592 5 жыл бұрын
great tips, Katie. And Jackson is adorable!
@katiegordon610
@katiegordon610 5 жыл бұрын
Isn't he
@ijustrealllylikecats
@ijustrealllylikecats 2 жыл бұрын
omg. I kept hearing my cat whining at my studio door, and then I hear you going "Jackson enough!" and it turned out that I was hearing both of our pets whining at us at the same time lol. I thought the sounds were all coming from my cat 😂
@ijustrealllylikecats
@ijustrealllylikecats 2 жыл бұрын
btw your pup is adorable!
@katiegordon610
@katiegordon610 2 жыл бұрын
Thanks
@kellyweber627
@kellyweber627 4 жыл бұрын
Thanks for sharing this 😊 I am new to this and I have had a few pendants that this happened to. Hopefully it will work for me! TFS
@GB58able
@GB58able 2 жыл бұрын
Oops, second comment, how do you handle the back? Do you use resin or something like Polycrylic? Your pendants are beautiful❤️ Thanks again.
@rebeccaharden6018
@rebeccaharden6018 Жыл бұрын
I would love to see you making these.
@GB58able
@GB58able 2 жыл бұрын
Thank you ❣️❣️❣️ I so appreciate this video. None of the videos I’ve seen discuss what to do with with resin ‘edge spills’…I’ve thrown away quite a few thinking they could never be fixed. Have you ever used UV Hard Resin ( black bottle with green foral pattern).?
@themadhousediaries
@themadhousediaries 4 жыл бұрын
Hahahaha. Who was the door opener. Hahaha. Buahahahah haha the dog. Like mine. I was wait a minute. She's like hey and I could smell a dogs doing. So relatable while crafting. 🤣🤦🏾
@pupawupagus
@pupawupagus 3 жыл бұрын
OH MY GOD THE BLADE. also thank you for the video 🥰
@wileycovington4497
@wileycovington4497 3 жыл бұрын
I'm cringing too.
@DebbiePike77
@DebbiePike77 6 ай бұрын
I use a soft nail file, fine and extra fine.
@user-dn9vd9xg9p
@user-dn9vd9xg9p 2 ай бұрын
I rubbed the alcohol on my diamond glaze and it totally ruined it. Left a bad hazy glaze on diamond glaze. Just FYI.
@johnknight5370
@johnknight5370 3 жыл бұрын
Thank you Katie.
@bubblemum
@bubblemum 4 жыл бұрын
My biggest problems with UV resin thus far have been trying to use mica based powders- the color is lovely, but the light doesn't penetrate through, and so I get wet spots inside of the gems, for instance. I suspect I will need to try only filling a little, then hardening it, repeat repeat etc. WIth 1 2 part resin I can fill the gem molds and let it sit and it is fine; it is only the uv which gets hard on the outside and stays wet inside.
@katiegordon610
@katiegordon610 4 жыл бұрын
Ya I'm using it to do a thin layer not to make a solid block of something id discuss this w people who make solid resin pieces
@islahaworth5887
@islahaworth5887 5 жыл бұрын
Love this video Katie. I have quite a few pendants in the scrap bin where the resin has gone over the edge and bubbled at the back. Thank you for rescue suggestion. Also would it be easier for you to waft a UV torch over the uncured resin just to set a little before taking to your lamp. xx
@katiegordon610
@katiegordon610 5 жыл бұрын
The concern I have w a hand held light is it is concentrated Ultra violet light which is ultimately what causes skin melanoma but other than that say I cure the outer layer like that one pendant then I tipped it too much you would get the rippling again mainly just to show how people could fix and issue not really how my issue was created because you make enough and u test w other resins its bound to happen at some point its more what do you do when that happens is what I was going for
@kingyoblock
@kingyoblock 3 жыл бұрын
omg your dog is cuuuuute!
@AWordonTheWordtv
@AWordonTheWordtv 4 жыл бұрын
do you not get sticky resin issues? I always do and don't know how to fix it
@katiegordon610
@katiegordon610 4 жыл бұрын
Cure longer just like we bake for an hr when it says 30 min when it says 2 to 4 min I do 30 and when it says 30 min I cure for an hr make sure ur light is the proper watts too for ur resin
@Gilliebeany
@Gilliebeany 4 жыл бұрын
I just did resin for the first time and my UV light was the problem, plus I wasn't layering thin enough
@katiegordon610
@katiegordon610 3 жыл бұрын
@Jeon Jungkook give it a try
@cadavher
@cadavher 3 жыл бұрын
I bought UV resin off ebay and it does not cure no matter what. It's hard as a rock, but tacky always. Even after curing for 3x the time. Sunlight doesn't work, UV doesn't work, I cant seem to get it to work sadly. I think its just the brand. Even in super thin layers it stays sticky :(
@abbymurphy4383
@abbymurphy4383 3 жыл бұрын
I’m having trouble with UV resin when coating polymer clay projects. The piece will be fully cured and hard but the moment I touch or lightly press with finger it leaves a finger print or a mark. I read that using rubbing alcohol helps, however when I used it only made my finish even more cloudy and matte. I tried to polish with my dremel, but I felt that only made the issue worse. I really don’t know what I’m doing wrong? I don’t know if maybe I’m not layering enough?
@katiegordon610
@katiegordon610 3 жыл бұрын
Try curing longer and make sure ur light is at least 36 watts i do 60 min for a 30 min resin and 30 min for a 2 to 4 min resin if its greasy u can wipe it off w a soft cloth and 70% or weaker alcohol not 99 it will dull it alot
@notursissy4488
@notursissy4488 Жыл бұрын
for my resin case, it is so uneven, adk how to fix it, i've done some tricks to make the resin spread evenly, but it doesnt work, do u have any tips?
@rebornboulevard9581
@rebornboulevard9581 5 жыл бұрын
Jessama Tutorials did a video on this - something about you have to go back to it after so long I think to check it and re-add it if necessary. Don’t quote me on that lol but it was something like that. Love your videos by the way ❤️
@katiegordon610
@katiegordon610 5 жыл бұрын
I'm her patreon member and I've watched every video she does two design pendants as do alot of others but I made these flowers and translucent cane with no tutorials I did a lental swirl for the base which is a common technique I dont believe I copied or plagiarized anyone of her videos she is a group member as well and I'm sure she would tell me on fb if I did copy her tutorial thanks for the note tho. She also usually uses regular resin not uv resin i still though this would be helpful for people having issues
@rebornboulevard9581
@rebornboulevard9581 5 жыл бұрын
Omg I wasn’t meaning you were copying lol! I was just saying that I’d seen her do something about resin shrinking if it was any use to you!
@katiegordon610
@katiegordon610 5 жыл бұрын
@@rebornboulevard9581 oh sorry must have read that wrong not a big issue sometimes w a certain uv resin I get a little spill but not often at all usually when I'm rushing which is what happened here. Figured I'd take the opportunity to show how to fix it
@rebornboulevard9581
@rebornboulevard9581 5 жыл бұрын
Haha no problem. This is a great video. I’ve never used uv resin before and the 2 part just takes forever to dry so it would be nice to try. I love this bead
@lydiacee9131
@lydiacee9131 Жыл бұрын
I just came across your video and was wondering about the silicone mat you have. It looked like it had raised areas so your piece was not sitting flat on the mat. Can you tell me where you purchased it. Thanks
@katrinaparris8013
@katrinaparris8013 2 жыл бұрын
Hi Katie, you have done so much experimenting I wanted to see if you would be so kind to lend some advice on using the product for a glass vase repair? It is a chip that I will need to fill and also I may need to add a small bit of light lavender. It is about the size of a half dime and the top will be flat once filled with the resin. How would you recommend tinting and any other tips?
@UraniumFire
@UraniumFire 5 жыл бұрын
Love your dog!
@yuselinmartin3502
@yuselinmartin3502 3 жыл бұрын
How long did you give it under the lamp? Mine take long and come out sticky I am using the same brand
@3939889ISME
@3939889ISME 2 жыл бұрын
When you use torch go over quickly, did the flame touches the resin? This is always my question as I can’t see the differences at mine (I didn’t let the flame touches the resin)
@rubymichelle
@rubymichelle 2 жыл бұрын
Im wondering the same
@debbiecarolla7511
@debbiecarolla7511 4 жыл бұрын
Gorgeous dog
@user-dn9vd9xg9p
@user-dn9vd9xg9p 2 ай бұрын
Are you also going to resin the back of these with the hard resin?
@katiegordon610
@katiegordon610 2 ай бұрын
I don't usually do the back
@IAMGiftbearer
@IAMGiftbearer 3 жыл бұрын
Will UV resin work on a high domed cabochon such as a half sphere or will it run off?
@persesrathert8324
@persesrathert8324 4 жыл бұрын
Can you tell me where you get your torch? I also wonder which uv light you use. Lucky you to have those beautiful dogs!
@katiegordon610
@katiegordon610 4 жыл бұрын
Tiny pandora light I have a video showing it my torch is just a little one off of Amazon
@ONEtreasures
@ONEtreasures 3 жыл бұрын
I had UV Resin with glitter separate from acrylic. What did I do wrong?
@mrpc333
@mrpc333 4 жыл бұрын
Does the resin discolor in time specifically over white? Thank you ahead!
@katiegordon610
@katiegordon610 4 жыл бұрын
Not that I have seen so far I mean when u apply it no matter which if the 6 or so resins I have they are not as bright after the resin is applied right off but I have not seen any of them discolor in the last year or so
@EJPARSONSUK
@EJPARSONSUK 5 жыл бұрын
Very interesting video and great tips, thank you. Am just starting out with UV resin and am in the UK, so not sure if I can get the RJ crafts resin. I've been using a resin off Amazon but not the same brand as yours. Do you have any trouble with the resin pulling away from the edges? I have seen your resin on Amazon UK, so would consider trying it if you have no such issues. Gorgeous beads by the way. Just subscribed to your channel and looking forward to checking out your other tutorials. Many thanks again, Emma 🤗😊
@katiegordon610
@katiegordon610 5 жыл бұрын
See my how to uv resin it pulls away some but then more is slightly needed so add a little more pull to the edge if it pulls away add a little more again until it stops
@EJPARSONSUK
@EJPARSONSUK 5 жыл бұрын
@@katiegordon610 Thank you. I saw and watched your 'how to UV resin' video just after I posted that message; very helpful. I'll give your advice a try .... fingers crossed 😊
@ValerieEarl
@ValerieEarl Жыл бұрын
I have also found that if it pulls away and you don't find out until after you have cured it, you can do the same thing that was done here. I add another thin layer, and make sure to pull it all the way to the edge, and it usually will fix that, too.
@EJPARSONSUK
@EJPARSONSUK Жыл бұрын
@@ValerieEarl Fab! Thanks for the tip. Still learning after all this time 😊🤗
@ValerieEarl
@ValerieEarl Жыл бұрын
@@EJPARSONSUK, you're welcome! Lol, I'm still learning, as well. That's why I'm watching KZfaq videos, haha. I'm still trying to get my sides to look good. I tend to get a lot of shrinking on my edges and they look awful. Experimenting and watching videos has helped a lot with previous issues. Good luck!
@christinebartleson3838
@christinebartleson3838 4 жыл бұрын
I’m so sorry to keep asking questions but I’m finding that there are a couple kinds of UV lights. There are lamps that have long light bulbs or most of them have LED bulbs. Are they both equally good or is one better then the other? Thank you so much for your help, you’re amazing
@katiegordon610
@katiegordon610 4 жыл бұрын
Well uv resin is not LED two different lights so I would say search UV light not LED lights also buy one known for PC if its confusing for you tiny pandora makes a light specifically for what do w PC. Or maybe Google the resin u plan on using and what type of light it needs then research the type of light if it says uv great if it says to use led then get one of those but uv is not the same as led yes they r both types of lights but they may not cure each product the same depending on what product u r using. Like some nail polishes both cure w uv and led but some only need one specific wavelength of light so the other would not work it's like comparing Pepsi to coke they r both soda and similar but different too I'm not an expert in this I just got the tiny pandora light because I know it works w most of the resins I plan on using w PC
@patsylou4867
@patsylou4867 4 жыл бұрын
What does pc stand for is it polymer clay and why does it not get cured like in a one inch tube pendant I have curd for hours and still got bubbles and it's soft can you use to much alcohol ink and powder will that make not cure it
@fbiagentfrank
@fbiagentfrank Жыл бұрын
I know this is an old post, but I didn't want to buy more supplies so I just tried my red carpet nail lamp and it works super well. Like, better than any other I've used. I bought it at ulta years ago and it came with a ton of extras so I can now do my own nails and make a lot of my own home decor and gifts. I'm saving so much money it's unreal.
@idarogers341
@idarogers341 2 жыл бұрын
Hi Katie, What do you do if you have small divets on the surface of the resin when you take them out from under the light? Do you clean your clay pieces before resining them? If so how do you clean them? Thanks
@katiegordon610
@katiegordon610 2 жыл бұрын
Um I don't usually maybe tiny tiny ones but because I'm wearing them I don't do a test piece something small like a quarter inch by a quarter inch I would just rub w 99 alcohol and thin top coat
@nanscott8872
@nanscott8872 3 жыл бұрын
Where did you get your bails? Thanks and awesome work!
@katiegordon610
@katiegordon610 3 жыл бұрын
All over Amazon. Etsy, ebay
@hollygreen8967
@hollygreen8967 Жыл бұрын
Ok so I use UV resin and after it’s cured I used alcohol to remove sticky but it makes it look dull! No matter how much I cure it it always looks dull! How can I fix that?
@24sevyn93
@24sevyn93 5 жыл бұрын
I like the blue and green bead. Can you show how you made the cane for that? Or is it in another video?
@katiegordon610
@katiegordon610 5 жыл бұрын
It is a barbed cane
@ashleyclarke1123
@ashleyclarke1123 3 жыл бұрын
So how do you remedy the smell after it's been cured? I just started using UV resin and it leaves a pretty strong scent on my finished product
@NarwhalPLURR
@NarwhalPLURR 4 жыл бұрын
Love the video but the way you're using that exacto knife gives me anxiety 😳
@katiegordon610
@katiegordon610 4 жыл бұрын
Well good thing they are my fingers and not yours right 😉
@Decopainterandtea
@Decopainterandtea 4 жыл бұрын
@@katiegordon610 I think she was showing concern, not criticizing you. At least that is how I read it.
@katiegordon610
@katiegordon610 4 жыл бұрын
@@Decopainterandtea I didnt think she was criticizing at all that's why I said what I said like Haha well good they r my figures not yours like if I were to happen to cutmuself it would be my own fault but what alot of people dont realize is I work w blades in a 1 inch space all day instruments sharp enough to slice ur finger open w no pressure at all with a tongue moving cheeks tightening and all kinds of other weird things going on my tactile ability is pretty attune and what's a little cut. Most the time I have a thumb or some figure fulcrum to prevent cutting but alot of people dont notice that either
@johnknight5370
@johnknight5370 3 жыл бұрын
I was thinking the same thing , I've done the same thing for years , most time I got away with but I've sliced the ball of my thumb a dozen times or so also, better to place against some thing and cut away , les control but less booboo's.
@Rock4jesus12
@Rock4jesus12 3 жыл бұрын
Did you ever have problems with curing? In made two batches of about 3 and only one of each worked, I’m really confused and frustrated especially because of the price of the Uv resin.
@katiegordon610
@katiegordon610 3 жыл бұрын
Nope but I cure longer than what they say I have two how I resin polymer clay videos which go through my process the updated one I believe I say how long I cure and what light that's usually the problem not a strong enough light or not curing long enough
@Sarahjewelry
@Sarahjewelry 3 жыл бұрын
love your work,iwanted to ask what to do with finger prints over uv resin?
@katiegordon610
@katiegordon610 3 жыл бұрын
Wipe them off just like glasses or mirrors smooth clear stuff like that will always get fingerprints unfortunately
@Sarahjewelry
@Sarahjewelry 3 жыл бұрын
thanks katie
@nemocurson2753
@nemocurson2753 3 жыл бұрын
Double like for the pitbull 😍😍
@annealbaugh919
@annealbaugh919 3 жыл бұрын
So kewl ! 👍🏻
@zamis21
@zamis21 3 жыл бұрын
My Dog Whine's every night around the same time and we can't figure out what she wants but man its annoying!! Ahh you have a Pit.. Yep its like having a permanent dog coat. Big babys!
@yadiradelvalle16
@yadiradelvalle16 4 жыл бұрын
i bought a uv light and also a uv resin hard and a siliconed sphered mold but its not curing properly it gets hard yes but it is still sticky. any tips and advice please im trying to make sphere pendants
@katiegordon610
@katiegordon610 4 жыл бұрын
If it's in a mold it might not be penetrating through the mold well enough I saw a resin tut once n the had to do half at a time check out regular uv resin videos
@babballard1
@babballard1 3 жыл бұрын
Hi Katie, can't find the disc for the Dremel, can you send me the link, if they are still available? thank you
@sergioknuf
@sergioknuf 3 жыл бұрын
Have you tried limino if so how does it compare to this?
@nancyt.pasour7658
@nancyt.pasour7658 2 жыл бұрын
Do you resin the backs of your pieces?
@abigailmorris1184
@abigailmorris1184 3 жыл бұрын
I can't seem to find any videos on it, but do you happen to know what to do if the resin is tacky/sticky when done curing? I am curing for the full time under the lamp, but my pieces come out sticky.
@katiegordon610
@katiegordon610 3 жыл бұрын
I cure 30 min for a 2 to 4 min resin and 60 min for a 30 min resin under the premis same as we bake clay for an hr even tho it says 30 min usually its undercuring also make sure u r using the proper watt light usually 36 w. And some will have an inhibition layer its an uncured layer of resin in the chemical process that needs to be wiped off w alcohol but I'd start w curing longer
@katiegordon610
@katiegordon610 3 жыл бұрын
Watch this one kzfaq.info/get/bejne/ocV2Y7Zym8WZo5c.html
@valeskalozada1540
@valeskalozada1540 2 жыл бұрын
Hii! One question! I have the same brand of UV resin and it looks perfect.. but after a few minutes directly under the sunlight it turns really really yellow!!!! Any advice? What should I do? Am I doing something wrong? Thanks!!
@valeskalozada1540
@valeskalozada1540 2 жыл бұрын
I have de deco one!!!
@odaveherdez108
@odaveherdez108 4 жыл бұрын
I'm new at this, I have a question. You don't put resin on the back?
@katiegordon610
@katiegordon610 4 жыл бұрын
Depends some projects I do some I don't if the back can be a front yes if not no I show u guys in the pendant projects if I do but really its personal preference and how comfortable you are doing that cuz if it runs u may ruin a side
@TheCof6656
@TheCof6656 2 жыл бұрын
If I try to wipe it with alcohol when it has a sticky layer, it will just smear and scratch the resin!
@adanvdousdi0922
@adanvdousdi0922 2 жыл бұрын
i am having that issue too. and no matter how long i cure it it is still tacky.
@notamberp
@notamberp Жыл бұрын
make sure you’re using 70% and not a stronger alc content like 90%
@rterry2752
@rterry2752 3 жыл бұрын
Cure bake the ploymere so that its got a curve before the dome resin ??
@katiegordon610
@katiegordon610 3 жыл бұрын
I'm really not sure what u r asking
@rterry2752
@rterry2752 3 жыл бұрын
@@katiegordon610 The dome rv resin makes it curve up. So pre curve it down while baking ?
@katiegordon610
@katiegordon610 3 жыл бұрын
@@rterry2752 i guess u could try to estimate how much it is going to curve before hand but that all depends on how many layers or how thick your resin is and how thin or thick your pendant is but hey if it bugs u may be worth trying I dont notice it when wearing as I said the little bit does not bother me one bit just pointing it out that it will happen w most doming uv resins compared to 2 part resin
@rterry2752
@rterry2752 3 жыл бұрын
@@katiegordon610 Got it, thanks tons.
@lisac7151
@lisac7151 3 жыл бұрын
I have been trying to make UV resin bookmarks and they won't lay flat. How do I avoid this? It's driving me crazy. Just like the piece you made but worse. Any idea of what I can do?
@katiegordon610
@katiegordon610 3 жыл бұрын
not really sure maybe a 2 part resin they dont really curve because it is a slow chemical cure
@lisac7151
@lisac7151 3 жыл бұрын
@@katiegordon610 I did solve it sort of. I put the light farther away from it and cured it slower as you mentioned with the two-part resin. It seems to shrink less when you do that. I wish I could use the other resin but I'm allergic to it. It's a shame because the UV resin does have some disadvantages. Thanks for replying.
@christinebartleson3838
@christinebartleson3838 4 жыл бұрын
What watt do you suggest? There are so many it can be overwhelming
@katiegordon610
@katiegordon610 4 жыл бұрын
36 is generally good but check the recommended per the brand resin. u intend to use
@Iris17591
@Iris17591 3 жыл бұрын
You gave me so much anxiety with that scalpel 😅
@katiegordon610
@katiegordon610 3 жыл бұрын
Haha hey I have blades like really sharp instruments in a 2 inch or less space all day working under the gums trying not to cut them I don't think people realize how sharp our dental instruments are I got good hand skills
@Iris17591
@Iris17591 3 жыл бұрын
@@katiegordon610 I should hope so 😂
@sherrimanoukian4718
@sherrimanoukian4718 4 жыл бұрын
How can I fix a doming issue, where the deco resin did not go all the way to the edge, can I add or I have to take it off completely?
@katiegordon610
@katiegordon610 4 жыл бұрын
U wanna make sure u pull it to and slighltu over the edge but if it pulls back far which it really never has for me others have but not that one 2 things I would do either re coat it fully or grind that little bit off the edge of the pendant to make it match
@sherrimanoukian4718
@sherrimanoukian4718 4 жыл бұрын
Katie Gordon thank you I’ll try it!
@roadstar499
@roadstar499 4 жыл бұрын
i am using the sun to cure my resin... not sure if its fast cure or slow...seems the thick like your fast cure... i have a 200 watt nail lite which only stays on for 90 seconds,,, i have tried hitting button like 3 or 4 times and its still very tacky,,, then i put out side for 30 mins and not tacky... any suggestions? do you have curing uv resin issue videos? thanks
@katiegordon610
@katiegordon610 4 жыл бұрын
Two of those videos click on my name on here click videos and they will be all under their I can not copy and paste in a response on my phone in the creator studio so check that way please at work so not access to a computer
@katiegordon610
@katiegordon610 4 жыл бұрын
A computer that is for personal use medixal facility lol
@user-sm4ho2lo3y
@user-sm4ho2lo3y 4 жыл бұрын
When I take the sticky layer with alcohol it takes all the shine too. Any ideas why these is happening?
@katiegordon610
@katiegordon610 4 жыл бұрын
I only use regular alcohol when I do that not the 99 percent like 70 percent I think it is. Also make sure you are curing long enough people who have issues asked me all the time and if they add another 10 min or so to the cure time most the time it fixes their problem
@TosaNewsense
@TosaNewsense 3 жыл бұрын
Some resins, especially the “soft” version, in my experience, leaves that sticky layer, no matter how long you leave it under the light. It’s called an inhibition layer, and is just part of the process, apparently. You just wipe it off with alcohol like the OP states. ITV hasn’t happened to me in a while though, so maybe newer formulation of UV resin don’t leave an inhibition layer?
@katiegordon610
@katiegordon610 3 жыл бұрын
One not cured all the way. Two using too high of an alcohol percent like 99 which will remove the shine use reg alcohol like from the drug store those would be my options
@kutufutubom7437
@kutufutubom7437 3 жыл бұрын
Hi there, I have this issue with uv resin where the smell lingers even after cured for days. Do you have this problem?
@katiegordon610
@katiegordon610 3 жыл бұрын
I have not
@robynnvillarreal1711
@robynnvillarreal1711 4 жыл бұрын
When my uv resin cures there are tiny minuscule bubbles even though I run a BBQ lighter to pop them. Any tips or suggestions as to why that is?
@katiegordon610
@katiegordon610 4 жыл бұрын
It happens to all of us some reains do it more than others
@robynnvillarreal1711
@robynnvillarreal1711 4 жыл бұрын
Libby's Cositas hi there! I use a 15 w uh light. I had a 36 w before but I thought it might help. It still makes a lot of bubbles
@hkreations5108
@hkreations5108 3 жыл бұрын
If it's RJ Crafts, why does it say DJ Crafts on the bottle? Just wondering.
@katiegordon610
@katiegordon610 3 жыл бұрын
It does say rj just the font is different so the bottom line for the r is small its Rhonda Jones but she has changed her business name in the last year or so
@hkreations5108
@hkreations5108 3 жыл бұрын
@@katiegordon610 What has she changed it to? In case I want to order something from her.
@katiegordon610
@katiegordon610 3 жыл бұрын
I actually don't know ask one of the fb sites people who have been in pc for a little bit will know she has her own fb page I don't order much but that resin and it's been a year or more since I have
@seniorzasader4328
@seniorzasader4328 3 жыл бұрын
FROM WERE u buy small drill
@katiegordon610
@katiegordon610 3 жыл бұрын
Amazon Amazon products I've ordered FOR USA ONLY at this point # commissions www.amazon.com/shop/katiegordon?ref=exp_inf_sh_mb_own_katiegordon_cp
@shadowfox6345
@shadowfox6345 3 жыл бұрын
I have problem when my uv resin curse its sticky how do I fix that problem??
@katiegordon610
@katiegordon610 3 жыл бұрын
Cure longer I do 30 min for a 2 to 4 min resin and 60 min for a 30 min resin under the same premis of we bake the clay for 60 when it says 30
@Crystalnachi
@Crystalnachi 4 жыл бұрын
Does this resin smell when curing?
@katiegordon610
@katiegordon610 4 жыл бұрын
When curing mine does not some resin has a smell normally but I have not noticed them increase when curing
@Crystalnachi
@Crystalnachi 4 жыл бұрын
I currently use Limino brand which works very well but it does have a smell when curing and I need to have good ventilation.
@katiegordon610
@katiegordon610 4 жыл бұрын
The decor rom does not seem to have a smell to me or the rj crafts again both have pros and cons. The tiny pandora does have a strong smell. The lisa pavelka one does not smell badly either just thicker even in the warmer weather
@Crystalnachi
@Crystalnachi 4 жыл бұрын
@@katiegordon610 I think that I will have to try. I have ultra dome, deep shine and Lisa Pavelka. They all have their good points. :) Thank you for your advice. It is much appreciated. :)
@angelinadamore6979
@angelinadamore6979 3 жыл бұрын
Sorry can i get the name of the resin in the tin please... Deco...
@katiegordon610
@katiegordon610 3 жыл бұрын
The decor rom? None r in a tin though
@angelinadamore6979
@angelinadamore6979 3 жыл бұрын
@@katiegordon610 yes sorry, i found it in the end, thankyou
@christelvannieuwenhove1436
@christelvannieuwenhove1436 4 жыл бұрын
my resin is always sticky even if its not in a mold ?? why is thaat and what can i do about it??
@katiegordon610
@katiegordon610 4 жыл бұрын
I'm not sure contact the manufacturer maybe something is wrong w the resin maybe your light is not the right watts for the resin
@amandamessias7161
@amandamessias7161 4 жыл бұрын
It happening with me too, i tried 2 types and all it ends stick
@alexblaney6322
@alexblaney6322 4 жыл бұрын
Your lamp is not strong enough , this happened with me with a small lamp I now use a 72 watt and it’s now not a problem .
@nightflash1352
@nightflash1352 3 жыл бұрын
I have tried some uv resin, but there are some lines on it when I cure it, can u tell me please What I do wrong as it does not become completely clear?
@katiegordon610
@katiegordon610 3 жыл бұрын
I have gotten clear ripples before kinda of like oil slick looking i think its when I over heated it or left it out too long when I was playing w it not really sure do small tests and try different things
@eskee1
@eskee1 3 жыл бұрын
You need to sand it with sandpaper all the way up to 1000 grit or more then polish it
@mercedesmarton3768
@mercedesmarton3768 3 жыл бұрын
3:52 🥰🥰🥰🥰😍😍🤗
@sharagamiel2719
@sharagamiel2719 4 жыл бұрын
Could you paint the uv resin on ?
@katiegordon610
@katiegordon610 4 жыл бұрын
If u want a super thin coat I dont get as good of results but play w it on baked scrap clay or pieces u made u r not happy w
@louisejeffries7155
@louisejeffries7155 3 жыл бұрын
Cute pitty
@MultiKwolf
@MultiKwolf 3 жыл бұрын
hard ;)
Using UV Resin A beginners Guide - Top 5 tips
28:36
Paula Storm
Рет қаралды 396 М.
How to put UV Resin on polymer clay, earrings, jewelry, tips & tricks, DIY
13:59
Sherbears Whimsical Clay & Mixed Media
Рет қаралды 3,6 М.
Running With Bigger And Bigger Feastables
00:17
MrBeast
Рет қаралды 165 МЛН
나랑 아빠가 아이스크림 먹을 때
00:15
진영민yeongmin
Рет қаралды 3,7 МЛН
Oh No! My Doll Fell In The Dirt🤧💩
00:17
ToolTastic
Рет қаралды 10 МЛН
*Brand new WOW* Resin Technique anyone can do
15:38
Claire’s Crafty Corner
Рет қаралды 80 М.
5 Ways to Color UV Resin | Resin Basics for Beginners
7:59
Lorien's Craft Box
Рет қаралды 138 М.
How I Glaze My Polymer Clay Charms (with UV Resin)
10:34
Creative Rachy
Рет қаралды 277 М.
5 UV Resin Gift Ideas - Christmas Inspiration!
16:07
Louise Singleton Creations
Рет қаралды 50 М.
#1594 Will It Work? Using Chameleon Powders In Holographic Molds
22:19
Pouring Your Heart Out
Рет қаралды 27 М.
polymer clay pendant 48
1:24:38
Katie Gordon
Рет қаралды 11 М.
UV Resin Mistakes You’re Probably Making
10:26
Oak & Lamb
Рет қаралды 55 М.
52. Testing the UV Resistance of 7 Resins
17:10
Tiffani Williams Fine Art
Рет қаралды 13 М.
Don't Miss Out On These UV Resin Tips and Tricks.
10:30
Steve McDonald Arts and Crafts
Рет қаралды 106 М.
Running With Bigger And Bigger Feastables
00:17
MrBeast
Рет қаралды 165 МЛН