2004-2009 Toyota Prius Engine Rebuild 4 | Piston and Bottom End Assembly

Рет қаралды 463

3 ай бұрын

This 2008 Toyota Prius is getting the engine rebuilt in vehicle.
🛒PARTS LIST:
▪️ Timing Kit: amzn.to/3QpdJ3p
▪️ Head gasket kit: amzn.to/3QjTQLa
▪️ Lower gasket kit: amzn.to/4dgvw6B
▪️ Pistons: amzn.to/3UvHdix
▪️ Piston rings: amzn.to/3wdQdj1
▪️ Connecting rod bearings: amzn.to/3xTxUAd
▪️ Main bearings: Recommend dealer
▪️ Water pump: amzn.to/44jHV5L
▪️ Thermostat: amzn.to/3w8B7ve
▪️ Radiator hose upper: amzn.to/3Wgrbdx
▪️ Radiator hose lower: amzn.to/3JDAz3I
▪️ Knock sensor: amzn.to/3WzzsK7
▪️ VVT Solenoid: amzn.to/3JCq28Q
▪️ Anti- sieze: amzn.to/42wZ2QS
▪️ Assembly lube: amzn.to/3ua1pMD
▪️ Dielectric grease: amzn.to/3HDPTMw
▪️ Ultra grey RTV (optional): amzn.to/3OuOjQV
▪️ Thread locker: amzn.to/491k78u
🛒TOOLS NEEDED:
▪️ Allen socket set: amzn.to/3ksxOWY
▪️ Breaker bar: amzn.to/42eP7Pq
▪️ Coolant funnel:amzn.to/4bfMaCk
▪️ Electric ratchet: amzn.to/3Sw4W12
▪️ Flashlight: amzn.to/48OaGJi
▪️ Flex head ratchet: amzn.to/47PZwm7
▪️ Impact driver: amzn.to/3FhU5kR
▪️ Impact socket set: amzn.to/3Hy3fKi
▪️ Impact wrench: amzn.to/3Sfmiht
▪️ Long plyer set: amzn.to/3u9Qkv2
▪️ Pick set: amzn.to/3u9AdNZ
▪️ Piston ring compressor: amzn.to/3Sbfq4G
▪️ Plastic scraper: amzn.to/4bh3oPI
▪️ Plier set: amzn.to/3uhTvRi
▪️ Prybar set: amzn.to/3IkSlWw
▪️ Socket and wrench set: amzn.to/4b6K8ob
▪️ Torque wrench 1/2: amzn.to/3AgaOB2
▪️ Torque wrench 1/4: amzn.to/493Xr70
▪️ Torx bit set: amzn.to/4b5WUTQ
▪️ Wrist pin puller: amzn.to/3Qzsxwz
😎If this video has been helpful consider supporting us with a cup of coffee! 🙂
www.buymeacoffee.com/ValleyMo...
➡️I am part of the Amazon affiliate program and get a small commission when purchases are made through the links provided.
🔺DISCLAIMER
The information provided by Valley Mobile Automotive (“we,” “us” or “our”) on this video is for general informational purposes and entertainment only and does not replace professional advice.
All information is provided in good faith; however, we make no representation or warranty of any kind, express or implied, regarding the accuracy, adequacy, validity, reliability, availability or completeness of any information on the video.
By working on your own vehicle, you take responsibility for the outcome.
Under no circumstance shall we have any liability to you for any loss or damage of any kind incurred as a result of the use or reliance on any information provided on this channel. Your reliance on any information on the videos on this channel is solely at your own risk.

Пікірлер: 5

@jafinch78 2 ай бұрын

Awesome series! Thanks for sharing. Very much appreciated. I was planning to make the same, so now thinking what I have left I've not seen with the Priuses is a YT video on DIY machining a head and block mating surface if required. Most likely using a granite cutting board that I found was ~0.001 or better or my granite surface plate for the head and a smaller surface plate for the block with sand paper if required. Videos doing on other engines, though I've not seen with the Priuses yet and I have a 2013 head gasket to do eventually and two 1.5L engines so far. I'd also like to do a video on converting the Prius C engine to fit in a gen 2. One of these days, though for now the woman has be rescuing gen 2 Priuses and getting them back to road worthy Toyota specs. Seems every parts car turns into a new car to move forward and the bonus find engines and batteries get sidetracked until required. 🙂

@krabbypatty3644 Ай бұрын

you da man

@rcf8367 2 ай бұрын

Good series, but cannot find your link for the “special wrist pin” tool you mentioned. I hope the rebuild lasts without boring to the next oversize…

@ValleyMobileAutomotive 2 ай бұрын

Thanks! This was a fun rebuild. They have driven it a few thousand miles and report no oil consumption 🙂. I'll check on that link, knowing me I probably forgot to post it 🤦🏻‍♂️