Keep up the vintage videos. I know there is not a lot of us. And most of us don’t know how to use computers. But these videos will be useful for years to come when these become popular when they become rare.
@baddarkvader3 жыл бұрын
The last time I performed this on a small frame was in 1984 in my best friends kitchen and surprisingly I remembered it so knew your next step to my surprise. We didn't do this procedure with the engine in the frame as we didn't know it could be done like this. Thank you I have subscribed and hope to learn some more.
@narrischernarrischer92045 жыл бұрын
Thanks for the Video! I also recommend NOT to use a 4 disc clutch, like from malossi, ferodo or other "sport" clutches, because the seperating of 4 discs when pulling the clutch is almost not possible. Problem is that the compressed spring is mostly not parallel and then the clutch discs don't separate. So you cannot get into neutral and engage other gears. Simply use the 3 disc clutches and the polini spring. Then all works very fine. I use this at a 130 polini, 19 SHB carburetor and polini exhaust. All perfect. Greetings from Vienna/Austria
@Vespanation Жыл бұрын
This video was so well done. Perfect descriptions, step by step, great video skills, just the best.
@rosewell19836 жыл бұрын
i like these videos. 45minutes of entertainment. Not just 4-5min or 15min.
@terrylee37886 жыл бұрын
Great video. Always good to learn how to perform work on your own equipment. Thanks.
@robertfields4836 Жыл бұрын
Watching from Ireland, Top stuff, Robert.
@rod_r6 жыл бұрын
Great video. Just about to do this myself so perfect timing ! I bought a clutch holding tool, but watching this, I just realised the tool wont work with the clutch in place because the clutch covers the tabs that the tool is supposed to sit into....will have to try the copper coin
@spencerpayne2464 Жыл бұрын
Lovely smallframe now Robot, keep up the video's. If it were mine I'ld have to 75cc or 110cc it.
@dodgydruid6 жыл бұрын
The old time honoured way was to soak the corks in oil for a length of time to maintain full penetration of the oil into the plates, I still use a ziplock bag whenever I does mine lol
@gmashe4 жыл бұрын
Thanks for that video. Really useful and makes it all too easy. However, I have a question - I'm new to smallframes. What would you suggest where the wheel hub - the blate in front of the brake shoes - doesn't want to come off? I tried loads of penetrating fluid, a puller and a heat gun and the thing just won't budge. I'm afraid to use too much brute force of a puller. Short of stripping the engine and splitting the case, any bright ideas??
@vivaldi9156 жыл бұрын
Very nice. Thanks for sharing mate.
@jaalgr6 жыл бұрын
Great video robot
@PhillipBolan1233 жыл бұрын
Very informative. Great video. Well done Robot
@VespaMotorsport3 жыл бұрын
Glad you liked it!
@efendi1716 жыл бұрын
Well done!
@jacgesjohn90583 жыл бұрын
How to remove the clutch outer out from the case?it is necessary to go from the other side of the engine?
@eigner-9002 Жыл бұрын
how to remove that primary and secondary gear?
@tianchongsun98675 жыл бұрын
Why do you apply oil on the clutch plates?
@KipBurbank12 жыл бұрын
Thanks. Good lesson
@yopifnuchannel81404 жыл бұрын
Amazing 👍
@djalil53 жыл бұрын
Why oil on the disque ?!!
@78a67h3 жыл бұрын
Should be wearing a helmet.......but I couldn't help myself. Ha, ha, ha.