Vittorazi Moster Plus 185 carburetor membrane replacement. Paramotor engine maintenance series.

Рет қаралды 18,152

4 жыл бұрын

Well, this particular operation requires a bit of patience, a steady hand and a clean desk!
Not hard to do though, if you know what you need to do step by step.
Here is how we do it in our workshops.
Feel free to have any question at info@scoutparamotor.com
Hey! Did you know we offer FULL MONEY BACK GUARANTEE with every Scout purchased? Find out more here: www.scoutparamotor.com/suppor...
Are you grounded and you need some spare parts for your paramotor? You will find all you need here, next day shipping: eshop.scoutparamotor.com/
You have some questions or even some problem? We are ready to help you. Ask for help directly! : www.scoutparamotor.com/support/
Check if there is a SCOUT dealer near you: www.scoutparamotor.com/dealer...
Do you have some cool adventure that you want desperatelly do, but you dont have sufficient funds? We have something just for you here: adventurewingman.org/
Like our facebook page: / scout-paramotor-offici...
Instagram: / scoutparamotor
Music: soundcloud.com

Пікірлер: 40

@LaurentEgliAdventure Жыл бұрын

I'm just about to service my carburetor myself. What a releif to be able to follow these instructions step by step. Thanks Stephan and Miro!

@milesb4231 4 жыл бұрын

About time you made this. Thank you.

@DougBowman6 4 жыл бұрын

Thank you so much 👍 Great subject to cover in detail. Look forward to your other carb videos 😎

@Les__Mack 3 жыл бұрын

Thanks for posting this. I was using the gasket with only one hole and the cut. Switched it out and runs great. Thanks.

@kd5uwg 4 жыл бұрын

Great video, but I feel you should have covered more on how to set the metering lever height, as well as checking and adjusting pop off pressure, over all excellent video I just would have like to have seen you include a little more on these two aspects of rebuilding the carbs.

@SCOUTaviation 4 жыл бұрын

Hi Calvin, this video is about replacing the membranes. We will have a video about adjusting the carburetor, pop-off pressure and other adjustments that will cover those. Thank you so much for your feedback!

@kd5uwg 4 жыл бұрын

SCOUT paramotor good deal. Just wanted to make sure, that people realize there is a bit more to setting up the carb. Even with just membrane replacements. I recheck my metering lever height and popoff.

@JD10Driver 3 жыл бұрын

I know it’s 5 months later but I hope I didn’t miss the carb adjustment video! If it hasn’t been made yet, would love to see it please!

@nice2care 3 жыл бұрын

@@SCOUTaviation Very much needed video. Hope we can see it soon!

@NCPPGpilot 3 жыл бұрын

This is an easy project. I'm actually here for the high quality video and chillin' to that smooth jazz. ~8^)

@cesarmiranda4820 2 жыл бұрын

Gracias

@RogerBarraud 4 жыл бұрын

06:50 Now that is *excellent* advice. :-)

@mamcgreevy Жыл бұрын

FYI, I tightened the carb screws to 10nm as mentioned in the video and cracked the plastic airbox connector. Found out in the manual that the torque should be 6nm.

@SCOUTaviation Жыл бұрын

ouch sorry to see that. seems like we did a mistake?

@geoffreyking1 7 ай бұрын

I did the same thing

@Chris-Fennimore 4 жыл бұрын

Great video series, thanks. Yes, I throw away the "fiberglass-like" pump diaphragm, as they do not last very long before they get a hole in them. But instead of using the rubber Pump diaphragm, I like to use the Mylar-based Pump diaphragms. Fuel with ethanol in it will cause the rubber-based Diaphragm port "Fingers" to curl up, and not completely cover the fuel pump ports like they should. The Mylar-based pump diaphragm does not have this reaction to ethanol, and will last years longer. I am surprised the see Walbro did not include the Mylar-based pump diaphragm in your rebuild kit.

@TONYPARAMOTOR 3 жыл бұрын

have u a link...? or search mylar based pump diahragm for walbro 37c kit?

@TONYPARAMOTOR 3 жыл бұрын

kzfaq.info/get/bejne/rs95ksphna6Zgo0.html

@techi3075 2 жыл бұрын

Nice video but no pulling needle jets for cleaning, no fuel screen replacement, and no metering/pop off setting.

@1falconron 4 ай бұрын

pop off 15 psi

@osmardutour2205 3 ай бұрын

hola,que diferencia hay entre walbro mrf090 y mpe090 ? se puede poner en cualquier moster ?

@madlankan6735 Жыл бұрын

How the fuel pump is driven by?

@justharryjohnson7250 4 жыл бұрын

I have heard the white membrane is better than the black one. Can you confirm or deny this ?

@chancer74 2 жыл бұрын

I understood that the lighter colored gasket is for AV gas only.

@conquistadorppg417 4 жыл бұрын

Where you measure the 1.2 to 1.6mm from? Can you use a walbro tool?

@TONYPARAMOTOR 3 жыл бұрын

yes you can. its far more accurate.shaped like a W

@petrnovak3732 10 ай бұрын

What type of walbro? I dont have the membrane 9:35 only gasket

@BigFlyingLoveMachine 2 ай бұрын

Same! Mines on a factory R

@andrewlapensee 4 жыл бұрын

Have you ever tried running alpine 2 stroke?

@TONYPARAMOTOR 3 жыл бұрын

HAVE YOU? whats it like?

@Tasmanian666 4 жыл бұрын

Moster 185 manual specifies 10 Nm for carburetor flange screws and 0.5-0.6 Nm for carburetor plastic connector screws. Are you sure the two screws should be tightened to 10 Nm?

@SCOUTaviation 4 жыл бұрын

Based on my experience 0.5 Nm is totally unrealistic for that flange. I know very well the manual, ofc. 10 Nm might be on the tight side, but using new gaskets I have found 10Nm to be spot on, without damaging the plastic flange anyhow.

@tyrden 2 жыл бұрын

Great video. I also question the 10Nm for the carburetor flange. At 10Nm the plastic flange begin to deform at the screws. I backed it down to about 6Nm but I’m concerned the damage is done. I’ll need a new plastic flange. Is there any new guidance from Vittorazi for the Moster MY20 Plus?

@superflytnt2978 2 жыл бұрын

Definitely not 10nm!!! I torqued the plastic connector screws to 10nm and cracked the plastic boot connector! Back it down to 5-6nm and check the connector every time as part of your pre-flight

@RogerBarraud 4 жыл бұрын

Cleaning? Gasket sealants? Lubrication? Why did you throw out the old gaskets before you unpacked the new ones? - I would be carefully comparing the new ones - especially where there are two similar-but-different ones supplied in the new kit... to make sure I was installing the correct choice. Any comments re what is special about these carbs? - Are they altitude-compensated? Why not fuel injection? More to go wrong? Thanks for the video anyway. Good production quality ... only nit would be the music is too much louder than the speech, and the usual bugbear of pumping compression :-/ Cheers!

@F.O.D. 6 ай бұрын

It didn’t show how to adjust the carb lever… just that one should. 😕

@RogerBarraud 4 жыл бұрын

Another nit: Your speech is actually quite muffled (no sibilance) much of the time. Not sure what kind of microphone you are using or its placement, but you are pretty obviously talking off its major axis most of the time; I can hear the sibilence come up sometimes, as presumably you shift around into its major axis of (treble) sensitivity... or something on the workbench reflects treble back into its sweet spot.

@Farinazion 2 жыл бұрын

The membrane @9:40 is wrong. You dont need this!

@petrnovak3732 10 ай бұрын

I dont have it there and it works fine.

@wiech61 2 жыл бұрын

Słabo , słabiutko właściwie nic nie pokazane , a najważniejsze czyszczenie malutkiego siatkowego filtra wcale , przy dmuchaniu może już poleciał , Wiechu