Hi Avp, thank you for watching! Happy waterproofing :)

Thank you for your support:)

Hi Mike, Visit our website and check out Gripset BRW PF or drop us a line at info@gripset.com for our recommendations, thanks for watching!

Hi Courtney, please email us at info@gripset.com with more details of what you're trying to achieve, but ultimately 38FC can't be used in this way. Thanks for your support.

Should be cement sheet

Same for me. No audio.

For further clarity, ive got a wall to wall shower, with a 90mm curb to entrance. At the moment the whole area is lined in cement sheet, puddle flange is recessed in just below the cement sheet level and the cement sheet is mounted directly on the yellowtongue flooring beneath, sitting perfectly level. Theoretically, water will never leave the shower area as the curb will always keep it within, but im worried about stagnant water not finding its way to puddle flange.

Hello George, could you give us a call on 1800 650 435 and somebody from our technical team will be able to help you out!

Hi Cain, Mark edges of flange with a pencil, use a cup grinder to create the recess to the nominal thickness of the flange. Glue flange to pipe and floor surface.

Hi, the application shown in the video is for a fully tiled bathroom using polymer modified, cement based tile adhesive, for advice on what specific materials are compatible to use over Gripset Membranes, send your enquiry to info@gripset.com, thanks for watching!

Hi Sam yes they are essential, you should always refer to the AUS standards and specific bathroom designs. Well spotted and thanks for watching! :)

Hi In0centz, Standard requirements can be found in AS3740 waterproofing of domestic wet areas and National Constriction Code, Gripset can recommend and issue specifications for projects to clarify details, just shoot us an email info@gripset.com and thanks for watching!

Hi, Sikaflex is solvent based sealant and apart from been hazardous to your health the product is not compatible with water based products. Unlike sealants Gripset Elastoproof B50 Joint band requires no drying time to overcoat, has up to 100% elastic recovery and rupture resistant its compatible with all 3 membrane classes and also unlike sealants is developed solely for this purpose. Multiphane is solvent based and would not work great for project in video as its specified as a bonded system and there will be a membrane over screed for direct tile as your probably aware solvent based membranes do not allow cement based products like screeds and tile adhesives to bond and there would be a high risk of failure. Thanks for watching!

@@GripsetIndustriesPTYLtd still works well here for us in Australia.. yours looks good too.

@@stephenc4161 what's the best stuff to use in Aus mate?

@@liamjenkins82 multithane mate. Elastomeric membrane. Idiot proof

@@stephenc4161 must be made for me!! Is it readily available. That k's for the reply. So many products out their

Hi Wan, The Puddle Flange is installed to the substrate which is typically flat. Falls to the waste achieved by laying of a screed.

Are gripset membranes specifically the 38fc and the Xpress, how are they with ponding water and re emulsification? Imo I would like to see the satisfactory falls created on the substrate using a gripset 11y and DM feather screed mix and then prime and waterproof over that?

@@GripsetIndustriesPTYLtd If the floor and membrane is flat, isn't this non compliant to AS3740? Section 2.3.1 states 'Where a floor waste is required in a wet area, the membrane shall be applied to a substrate with a minimum 1:100 fall towards the floor waste'. I would think there is risk of ponding if the membrane is flat.

​@@w37320 Hi Will, this is correct. This is one of the notable changes to the 2021 standard. The membrane must be applied over a graded surface with fall to alleviate any ponding. All Gripset wet area membranes are resistant to re-emulsification once cured. Thanks for watching :)

Hello Chris, unfortunately we do not sell Gripset in the United States!

hi vzgsxr, CFC sheet installed in this video was epoxy joined and sealant applied prior to membrane application, Gripset Elastoproof joint band could have been used to seal and act as a bond breaker. Thanks

Follow the Manufacturer Directions This is the way this product is Used It Tried and Proven If Don't mind me saying you are doing What most do , you mix the application Up , Different brands use Different application it to do with the Make up Of product Ps You don't run Different Brands of Tyres on one car

Hi, could you please specify what product was used in your bathroom renovation? thanks

I believe he used ardex not sure on the specs

@@In0centz then you would need to know the name of the product and refer to the TDS used for ardex product

Hello Xử Lý Chống Thấm, Gripset 38FC is a water-based liquid membrane.

Hi Jay, with the Gripset tape bond breaker systems there is no requirement for sealants

Hi Antonio, Gripset B50 Elastoproof used at all the corner junctions offers a instant ready to coat waterproof junction and far superior performance than any sealant based bond breaker we guaranty it will out last caulk. Floor joints where sealed with sealant, give us a call on 1800 650 435 to organise a product demo, thanks for watching.

Hey Frerik you're spot on, we have updated this video, glad you're paying attention and thanks for watching! :)

Probably waterproofing a wet area, I believe you use a shower and bathroom every day

@@paudiegaynor2786 Probabilities and assumptions ain't do nothing to help diyers