Comparing the cockpits of the Zoukei-Mura and Meng F-4G Wild Weasel kits.
Пікірлер: 18
@TheModelGuy Жыл бұрын
Not going to lie; won't be getting a Weasel until this series is finished.
@michaelnaven213 Жыл бұрын
Outstanding work on both Matt!👏👍👨🦳
@martinoude-vrielink7956 Жыл бұрын
Greetings from the Netherlands. Matt, you always have great videos, always love watching them. I currently put 2 ZM F-4EJ Kai to my stash because of the awesome yellow and blue anniversary paint schemes. Love japanese F-4 in general. Will keep an eye on the fit of the cockpit, thanks for the warning. The Wild Weasel I will wait until you completed the series. Maybe that one I will take the Meng and put some effort adding detail in the cockpit. Pity they did not include the pilot figures as in their Hornets. Keep up doing the great videos.
@stephenwheeler76 Жыл бұрын
Well done, thanks I still need to get one will wait for a few more shows
@andrewdunn9550 Жыл бұрын
I had the same issues fitting the ZM cockpit into my early E kit. I thought it was operator error so I am relived it isn’t just me. Heads up that I had some seem work where the lower forward fuselage joined the main fuselage pieces when I brought it all together. Not that hard to fix though.
@mancheungahyeung2104 Жыл бұрын
I will go for Meng just because the upper fuselage is one piece. The cockpit details are DIY dreams. However, I must admit ZM is better looking overall.
@adam_mawz_maas Жыл бұрын
I got lucky with the sill fit, but that may have been assembly sequence, I test fit everything before gluing the sill and actually tacked it in with the fuselage mocked up.
@DoogsModels Жыл бұрын
Maybe. On my F-4D the starboard side fit great and it was the port side that was squirrely. Was trying to test fit everything here but something obviously snuck through.
@danwilliams1686 Жыл бұрын
The ming looks to be a lot easier to build than the other one which is more detailed, ugh. But , I can make a map case and some wiring. So, have evergreen will travel .
@R08U5 Жыл бұрын
There we have it; silliness 😁 Great shootout. Although a draw, the question could also be: would you rather spend time fitting the Zukei cockpit or spend time modding the Meng one to Zukei's standard.
@MarcvanderWalle Жыл бұрын
Pimping the Meng cockpit using CAD designed 3D prints sounds good to me - Does anyone have any idea if anyone 's working on that? Great video by the way.
@paulwilson1529 Жыл бұрын
are you going to scratch the rats nest of wires to both rear ips matt? they seem naked without it. or are you keeping that stuff to a minimum for the purpose of a purer comparison
@DoogsModels Жыл бұрын
Oh I have plans
@tomspettel3646 Жыл бұрын
To fit is almost everything. If the parts don’t fit its worthless to me. I had a kit once where the wings would not go together and i mean over a 1/16th of an inch plus i did everything i could and no go. It went in the trash
@ponz- Жыл бұрын
Shit you know my uncle bob?
@michaelnaven213 Жыл бұрын
Red Fox is cheating.😂
@robertchaney8684 Жыл бұрын
Your use of profanity should be commended, one approximately every 45/50 seconds!