Ive always used green slime on the outdrive o rings plus before installing the gasket i smear that completely both side with green slime also. Then finally, i tighten down the 4 screws in a cross pattern rather than going round in a circular fashion. As for battery strap, go for something with rubber straps. This helps the chassis to flex correctly and reduce the chance of tweak in a crash. Ive a nice jc one. If you have some spare cash, get the kashima shocks and polished shafts they feel sooooooo smooth!!

I had the same problem with the diff, even bought a complete new housing and tried again, but same problem. I ended up using silicone sealant in combination with the paper gasket. So far so good.

For the battery hold down I went with the Exotek (EXO1828) and it's fantastic carbon fiber goodness. Jconcepts servo mount (JCO2948-1) is wonderful if you like a one piece aluminum option. Alternatively, Avid Racing (AVD10110) offers a carbon fiber servo brace.

Awesome video! Keep this up. Also my diff leaks too. No idea why thinking of covering the gasket and screws in green slime

The stock differential cover doesn't seal very well. Mine leaked from the start on my B6.3. On my B6.4 I noticed the seal surface wasn't the straightest. I've found them to be warped or can warp easily after tightening them down. I would highly recommend the aluminum diff cover. Associated part number 91781. I usually recommend this one item to all the Associated drivers since it made my car more consistent since it actually kept the fluid in the differential.

As far as the differential is concerned I had the same problems with our 6.2 stadium truck My mistake was OVER filling the diff. With the sun gear and the spider gears in fill just 1/2 way Do not cover the spider gears completely

Great video, and I've just ordered 2 of those pill containers :) Just checking is the part number for the rear pill block 91688, Thanks Megan

Great video on the 6.4. I'll try and help with the diff. It doesn't say it in the manual but I think you need to flip the gasket around. It won't make a mess anymore. Should work it's something that should be in the manual. Take care

Vision racing makes an amazing carbon battery hold-down using bands…

Try the Reefs Rc 299:lp Red edition : racing servo

💯💯💯💯

I use the yokomo gear diff , got tired the associated leaking all the time , hope that helps

Good video. Savox servos are the way forward. Are you able to share your setup sheet?

i know this video is a few months old, but have you tried the front wing in the upright position? (refer to ryan harris' TLR 22 5.0 setup video) and have you tried a titanium screw kit?

Love the video... fantastic! So what alloy diff case did you go with?

Awesome video!! Can you give me part number to the shock pistons and exact hole size to drill

I notice you are using the End Bell fan mount and not the Laydown mount. Does the End Bell mount keep your motor cooler?

I have a B6 to build , just buying parts for it for out doors grass dirt track , 17.5 motor , do i need a small fan for the motor ?

Getting back in the game soon. Had the original rc10 when I was a kid. I love to build these cars. What brand and car do you recommend to get? Thanks

also for first time fun/ newbie race will the stock shocks be ok ?

What c block did you use. Just the regular B6.1 one? Do you have a part number by any chance. Its nice thr 6.1 stuff fits the 6.4

I see you use the 3 hole pistons In shocks. Is that front and rear ? And do you drill fronts same size as backs

I should have waited you answer my question.

I've tried the B6.1/6.2 D mount on my B6.4 to achieve zero rear toe angle as you suggest, however the driveshafts bind when the rear suspension is compressed. Did you fit shorter driveshafts too?

All three of my AE 2wd vehicles have diff leaking problems. Tried a bunch of different things to solve it and none work. Would say it's the only down side of the vehicles

Where can u get shock internal washers

They look a bit too complicated for us. Where do you race them

What oil in shocks you running? Also what size holes in pistons.

It’s already 2023 and pro kits still comes with plastic servo horn..😂

Surprised you went with 3 holes in rear. Thats more along dirt setup. The 2holes will move less which is what you want for high grip. Here in the states the 2 hole pistons feel great