Wheel Spacers Install On A Tesla Model 3 Performance!!

Рет қаралды 10,930

3 жыл бұрын

Wheel Spacers install on a Tesla model 3 performance
I go over how to install and what is needed in this video.
If you are interested in these products they can be purchased through these Amazon links:
Tesla Wheel Spacers Front amzn.to/3BJH5Ar
Tesla Wheel Spacers Rear amzn.to/3i5GNfv
Other Tesla Stuff Like:
Tesla Splash Guards amzn.to/3iSmmll
Tesla Jack pads amzn.to/3rz6mcd
Tesla Model 3 Trunk Divider amzn.to/2TAFmwe
Tesla Model 3 Armrest Storage amzn.to/2UUdK5M
Tesla Model 3 Center Console Wrap amzn.to/3iOlsq8
Tesla Model 3 Trash Can amzn.to/3yjlpsM
Tesla Model 3 Center Console Organizer amzn.to/3x66wJ9
Buying a Tesla?? Make sure you use someones Referral link
Use my referral link to purchase a Tesla product and get up to $1,000 off and other exclusive benefits. ts.la/andy493616

Пікірлер: 67

@gulsoomkadir2584 2 жыл бұрын

I'm quite sure there is torque specs for the lug nuts for the hub and the spacers I would definitely do that.

@rich_33 2 жыл бұрын

Need to know what came with the spacer kit and why you didn’t replace the screw you took out of the hub and do you have to replace that screw before putting the spaces on.

@blower1 Жыл бұрын

Your a brave man to put wheel spacers on uber-turbines which have almost stretched tyres and already have a lot of poke (far more so than any other tesla or other OEM wheel for that matter)

@JohnD0129 9 ай бұрын

How are the spacers holding up ?

@kukwut Жыл бұрын

What size is the spacer for the rare wheels please? 15mm or 20mm?

@JoseTorres-gm7iy 2 жыл бұрын

Did you have to do any modifications to front?

@elbertmontgomeryjr7556 3 жыл бұрын

Thank you for sharing. I am planning to place similar wheel spacers on my 2018 Ford Fusion SE. I noticed that your wheel studs stuck out from the holes on the spacer. I have viewed several videos that say that it is bad for your wheel studs to stick out for the wheel spacer, because it keeps the wheel from sitting flat on the wheel spacer. Was that an issue you experienced? How did you get your wheel to sit flat against the wheel space even tough your wheel studs were sticking out from the wheel spacer?

@AndysAutoCarePlus 3 жыл бұрын

These wheels had room so wasn’t a issue. I think I showed that in the video but I will have to go bad and look.

@Drbeto209 Жыл бұрын

have you had any problems with them on?

@justinstewart3248 9 ай бұрын

Why did you have to take the bolt off the hub cover?

@grigor9144 4 ай бұрын

Did you move the car so the suspension settles after lifting it? lol doesn’t look like it

@robertpacheco8408 2 жыл бұрын

for sure should be torquing those bolts to spec, believe BLOX calls for 100ft/lbs whereas the actual lug nuts are 120ft/lbs-ish.

@AndysAutoCarePlus 2 жыл бұрын

Yes you are correct

@jezza6575 2 ай бұрын

129ft lbs for lug nuts

@JurajOreskovic 11 ай бұрын

Great video! I have 25mm (1'') lower Eibach springs and H&R spacers 17mm front and 17mm rear on my M3P 2023. with OEM Pirelli tires 235/35/20. Do you think if there will be a tire rubbing if I mont wider tires - 245/35/20? I would really appreciate the advice!

@AndysAutoCarePlus 11 ай бұрын

To be honest, I’m not exactly sure I’ve heard of people going quite a bit wider tires without rubbing issues though there’s a lot of space in there. Thanks for watching. I appreciate it.

@James-fy2sq 9 ай бұрын

I just put on 255/35/20 AS4s on mine and somehow it rubs on stock suspension... (fronts rub, rear is good - lots of clearance) Adding 20mm spacers fixed it

@dlastgate 2 жыл бұрын

Would you recommend 20mm for the front and 25mm for the rear tires?

@grigor9144 4 ай бұрын

@0barrington0 Жыл бұрын

Torque specs would have been good to mention in the video but I found them when looking through the comments at least.

@AndysAutoCarePlus Жыл бұрын

Yes, I did forget to mention that. Pretty much did this video on the fly just to try to help people.

@markdaughton7747 2 жыл бұрын

Stance looks great. However, I'm curious about your thoughts after driving the car.

@AndysAutoCarePlus 2 жыл бұрын

I have since removed the front as I felt a little shimmy on a long trip. Back is fantastic!

@regimantasliepa5330 2 жыл бұрын

Any issues or observations only running spacers in the back?

@tonewin9743 Жыл бұрын

@@AndysAutoCarePlus the shimmy is because the wheels don't clear the studs. U have to run a 20mm spacer up front. The pockets on the back of the wheels aren't deep enough so the wheels are not sitting on the centric ring correctly.

@ashegam 5 ай бұрын

The front was just fine, it's only the back that needed fixing. Now the front overshadows the aggressive look the back could have had.

@grigor9144 4 ай бұрын

True

@TeslaSoCal Жыл бұрын

How do the spacers affect the car's acceleration, braking, and handling?

@AndysAutoCarePlus Жыл бұрын

I never felt a difference.

@ronaldcarter5168 Жыл бұрын

I know this is a relatively older post, but will Tesla void your warranty as a result of adding the spacers?

@AndysAutoCarePlus Жыл бұрын

I actually don’t know that’s a good question though

@zelo533 11 ай бұрын

Probably depends what warranty, if your suspension gets f'd up, yeah, Tesla will probably reject your claim.

@freddyhadiyanto4199 Ай бұрын

without the 10mm screw the steering wheel will vibrate😂 is there another solution?

@jorgeninoderivera8197 2 жыл бұрын

Is it okay to leave the from stock and go 20 mm in the back ?

@AndysAutoCarePlus 2 жыл бұрын

I have since taken the front ones out and now stock up front.

@codyx561 2 жыл бұрын

@@AndysAutoCarePlus so stock front and 20 mm rear?

@illyrian5240 2 жыл бұрын

If I add 10mm on my 2015 ms do I need to get bigger studs ?

@AndysAutoCarePlus Жыл бұрын

I’m not sure to be honest

@michaelchu802 2 жыл бұрын

Dude no torque specs on those spacers ?

@vulshar21 Жыл бұрын

hey, i read a lot of comments stating that 15" spacers on the front requires the lug bolts to be shaved. It looks like you didn't have to do that. Can you confirm that the lug bolts going into the indents on the back of the wheel arent touching?

@AndysAutoCarePlus Жыл бұрын

I believe they actually were touching after this video. I actually ended up taking the front ones off because I had a slight wobble.

@vulshar21 Жыл бұрын

@@AndysAutoCarePlus ya i had that issue too with 18mm spacers. Not the lug bolts for me but the rotor screw had to be removed. I had a wobble and my brakes became spongy somehow until I removed that screw. Thanks for the video though!

@grigor9144 4 ай бұрын

Lmao you left the screw on that’s insane

@Marvelofebikes 2 жыл бұрын

How does it drive in comparison?

@AndysAutoCarePlus 2 жыл бұрын

To be honest I ended up removing the front ones now it’s great. 😃 I had some small vibration in the front.

@rm1626 2 жыл бұрын

@@AndysAutoCarePlus any issues running only the rear at 20mm and stock on the front? is that too much of a difference?

@downshift00 2 жыл бұрын

I thought the 15mm spacers won't fit on the performance ones since the wheel studs hit the back of the stock 20" wheels? Maybe that's why you had some vibrations since the wheel wasn't fully flat?

@rm1626 2 жыл бұрын

Blox (bonoss) told me the same...is there any work around? 18mm just took much poke for front wheels. They suggested to shorten the original wheel studs but I don't want to mess with that. Any downside to going stock on front and 20mm on rear?

@downshift00 2 жыл бұрын

@@rm1626 there is an alternative. Search for tesla 14mm h&r spacers that have an extended lug nut

@rm1626 2 жыл бұрын

@@downshift00 the problem is that the original studs stick out too much the thinner the spacer...how would going thinner help? I searched...couldn't find...link would be appreciated. To be clear its the 20inch uberturbines that don't have deep enough cavities for the original studs to fit into.

@downshift00 2 жыл бұрын

@@rm1626I know what the problem is. The 14mm spacers I mentioned do not have studs.. You slip them over your current studs and use the extended lug nuts so you can use a thicker spacer. Google them and you will see what im talking about.

@rm1626 2 жыл бұрын

@@downshift00 ahh ok makes sense thanks I'll look!