Every new bike needs this service before it's ridden!!! They ship them without sufficient grease and overtightened. Most shops don't bother to even adjust them properly.
@sergiomengualАй бұрын
I just have the same hubs on my bike. Excellent hubs.
@PP-cm4reАй бұрын
Loose bearings are the best. Easy to maintain.
@midwesttreasureandrelicrec7914Ай бұрын
I'm No mechanic, but have built a few of my own bikes just wondering if it would have been best to take off that brake rotor? To avoid contamination.
@user-xc6xg6xx5uАй бұрын
Лишняя работа
@JWKEL8814 күн бұрын
What’s the grease or lubricant so nice
@katiequark8882Ай бұрын
I feel like it might be important to track where the axel is before working on the hub, you could move your wheel too far to the left or right, making the handling worse and ruining your chain line.
@markholm7050Ай бұрын
Don’t undo the locknut and cone on one side. Put it back together with the same orientation as when you took it apart, and the spacing will be the same.
@minimoose921Ай бұрын
Only undo the non drive side. And you should have about 5mm extend past the lock nut( for a QR axle). The only way you could ruin the chain line would be to mix up your spacers
@enlightenedpreparingep4006Ай бұрын
Good to go 👍🏻
@hanyaoyap1826Ай бұрын
Nice
@Eric.V.Ай бұрын
Bro, you need to gently finesse that inner seal out. NEVER aggressively rip it out with the screwdriver like that!!! 😎
@robertmcfadyen915627 күн бұрын
Exactly .
@user-kv9ip1gp5vАй бұрын
I'm struggling to do the rear one🤦
@Kacavida11Ай бұрын
Try firs tighten the side (cone and nut) with the longer spacing, once mounted it will be underneth the kazette/freewheel and trhen the non drive side finding/feeling the proper tension on the bearing
@Jacksparrow4986Ай бұрын
Wo kann ich passende konen bestellen? Bei ebay habe ich welche mit metalldichtung bekommen die nicht passen, andere habe ich nicht gefunden. Fahrradhändler hatte mich letzt direkt wieder raus geschickt als ich mit einer Kleinigkeit kam (zu beschäftigt)...
@LolwutfordawinАй бұрын
Die metalldichtung kann man entfernen, dann sollte es passen. CNC bike hat manchmal welche im Angebot als set mit achse & Kugeln, die sind für shimano, sollten aber auch hier passen.
@Jacksparrow4986Ай бұрын
@@Lolwutfordawin achsen hab ich jetzt schon, kugeln hab ich separat geordert. Wie bekommt man die am besten ab?
@LolwutfordawinАй бұрын
@@Jacksparrow4986 brauchst unbedingt Konus Schlüssel, die sind deutlich dünner als normale Maul Schlüssel, ohne ist echt mies. Schau am besten, ob es in deiner Gegend eine fahrradselbsthilfewerkstatt gibt. Die meisten größeren Städte haben eine! Ansonsten findest du auf KZfaq genug Anleitungen dazu :)
@Jacksparrow4986Ай бұрын
@@Lolwutfordawin konusschlüssel habe ich, ich meine die Metalldichtung. Blechschere und Schleifpapier?
@LolwutfordawinАй бұрын
@@Jacksparrow4986 ich lege den Konus meistens einfach do in Schraubstock, dass die Dichtung aufliegt und klopfe leicht mit Hammer gegen. Wenn es kein vollintegrierter metallflansch wie an alten DDR Rädern ist, sondern nur so ein aufgesteckter Metallring geht das super.
@benjleath9406Ай бұрын
Never take them lower seals out of the Hub, they buckle up and then never go back in properly
@TheBlackRaven88Ай бұрын
Co to za smar którego używasz?🙂
@LTUGangАй бұрын
Motorex Fett 2000 bike grease
@danielmateusz9293Ай бұрын
każdy smar da rade.Nie słuchaj który najlepszy.
@toebusterАй бұрын
Except the problem is usually that the cups are pitted.
@robertmcfadyen915627 күн бұрын
The cone wrenches shown are poor quality . Single ledge ones are more durable .
@severs1966Ай бұрын
Never re-use hub bearing balls. Throw them away and put in new ones.
@user-xc6xg6xx5uАй бұрын
И убьешь конус и чашку
@user-xt6en9xt8xАй бұрын
В Москве не такие богатые люди, чтобы полотенцем смазку вытирать. Мы русские используем бумажные салфетки или туалетную бумагу.
@sergioandrada922Ай бұрын
Exacto, en Argentina también, papel y gasolina. Saludos !
@user-qk4fz7wn9cАй бұрын
Полотенце можно потом постирать,выходит даже дешевле.