Whirlpool Duet Dryer F01 Error Code Fix | Control Board Replacement

No video

Whirlpool Duet Dryer F01 Error Code Fix | Control Board Replacement

Рет қаралды 149,728

Күн бұрын

Our Whirlpool Duet dryer (Model WGD9200SQ1) won’t start, giving an F01 error code. Looking to save significant money I tackled the job and captured it on video for reference. The general approach in the video is likely relevant to other Whirlpool brands like Maytag or Kenmore (Sears) too, part numbers may differ, please do your own diligence.
This is the replacement part I use in the video:
Genuine Whirlpool W10174745 Control Board amzn.to/4bteOzR
(It’s a different part number than the part that failed but is compatible and working great now several years after the fix) other exact match part number links listed below.
These are the steps I took:
Unplug your dryer and carefully move it away from the wall you’ll need access to a couple machine head screws. Keep in mind you are still connected to a gas line.
Remove the top panel gaining access to the control board (2 machine head screws, use a nut driver).
Carefully remove the various plugs from the wiring harness into the old control board. Some of these have a rocker release, others pull straight out, the ones at the end of the control board have a latch style release. Take your time here, you don’t want to break or force anything here as you need to re-use the harness and connectors as is.
Remove machine head screws at the ends of the metal cross piece that holds the dryer control board. Slide the cross piece toward the rear to remove it from the front slot, and lift it out.
Remove a single machine head screw that holds the control board to the metal cross piece. The control board can now slide and be removed.
We removed our old control board by releasing it carefully from the 6 plastic tabs holding it into the plastic cradle. Once we had access to the bottom of the control board it was easy to see the point of failure. We tried cleaning the area and re-soldering but were unsuccessful.
My original control board had the following competing serial numbers:
W10182366 (On the plastic cover) amzn.to/33ncTub
W10110641 (On the board pink label) amzn.to/33kOVzZ
Both appear to be compatible to my dryer model, but do your own research.
Again, this is the replacement part I use in the video:
Whirlpool W10174745 Control Board
amzn.to/4bteOzR
Support the channel if this helped you:
www.buymeacoff...
Thanks!
Check out my other Whirlpool Duet repair videos:
Whirlpool Duet Gas Dryer Not Heating | Thermal Fuse Replacement
• Whirlpool Duet Gas Dry...
Whirlpool Duet Gas Dryer Not Heating | Gas Valve Solenoid Coils Replacement
• Whirlpool Duet Gas Dry...
Whirlpool Duet Washer Door Hinge Replacement
• Whirlpool Duet Washer ...

Пікірлер: 210

@Virtual98741 2 жыл бұрын

Thanks! Even after 2 years your video is still helping people like me. I had the exact same burnt connection and resoldered it. My dryer works again! 👍

@MattsGarageMiscDIY 2 жыл бұрын

Well done!

@thelegokids4760 Жыл бұрын

You saved me the cost of a replacement dryer! I found a person on ebay who solders the boards for $44, while looking for a used board. I sent the board off and it came back within days. If it hadn't been for this video, I would not have known what to look for on the board, and that even if I had to get a new board, it would have still been $100s less than a new dryer! I took a bunch of pics of the wiring set up and the whole re-install took less than 15 minutes. Thank you so much!

@3gypt1an Жыл бұрын

Tip to others .. with an exacto knife you can carefully scrape through the green trace close to the relay pin to give you much more copper area to solder. Also scrape along the relay pin to give more clean area for the solder to hold. If you have a little electronic friendly flux paste .. that does wonders too! Thanks to the OP for this excellent video. Saved me hundreds $$!!

@youralying8530 10 ай бұрын

Had the error code show up and when the service technician showed up, he claimed the part was no longer available (OEM). Looked through Amazon and picked up the closest match which included the white plastic attachment box for the circuit board. My son and I tackled the project and was able to replace the control board in about 1.5 hours. Hardest part was carefully unplugging some of the original connections without damaging the wiring and realizing that both of the anterior small wiring connections had to be attached at a different 90 degree angle (no real problem). Great satisfaction having that dryer up and running. Great video and commentary..big thank you!.

@MattsGarageMiscDIY 10 ай бұрын

Well done, glad it was helpful.

@skisumo Жыл бұрын

Thanks Matt $250 dollars saved. I went to Lowe's and bought a Weller Cordless Battery Powered Soldering Iron for $22 and soldered the burnt spot on the board and it worked! I couldn't believe it.

@pomiller1972 Жыл бұрын

I have the same battery soldering iron

@CategoryGaming-ko2qi 2 жыл бұрын

Literally just fixed my whirlpool because of your video! Was about to buy a new dryer when it only cost me 180$ to buy this part instead. Thanks a ton for making this video

@MattsGarageMiscDIY 2 жыл бұрын

We’ll done Cj, always glad to hear it was helpful!

@brandonhamilton3705 3 жыл бұрын

I had the exact problem as obviously a lot of you have had, thanks for a great video but luckily enough that I soldered the heck out of it and completely covered the lil nub sticking up and plugged it all back up and viola I have a working dryer. But without your video I wouldn't have got anywhere. Thank you so much for sharing?

@MattsGarageMiscDIY 3 жыл бұрын

Well done Brandon. That is super satisfying right! Glad it was helpful.

@angielee1111 3 жыл бұрын

Thank you so much for this video! I was going to buy a used dryer when mine quit working because I didn’t have the funds for a new one. You’re video saved me several hundred by buying a $160 part instead. 😊

@MattsGarageMiscDIY 3 жыл бұрын

So glad it helped!

@scottgriffith6895 3 жыл бұрын

Awesome video! Thanks and done in a quick hour. Exactly the same short issue you had in your video. My wife will NEVER leave me know knowing I am a DRYER WIZARD!

@MattsGarageMiscDIY 3 жыл бұрын

Glad it helped!

@JuanRodriguez-hb8ce Жыл бұрын

Hi Matt. Even now your video was awesome. My unit had the exact same problem. Even down to the smoke spot. Re-soldering did it for me. Wanted to add for benefit of others, that the blown solder location is at the relay. The blowout took some of the PCB material out (the little copper highways) at the location, so just adding soldering will not help. Re-soldering should make sure the relay leg makes contact again with these. Even adding a shunt wire between the relay leg and the next location would work. My wife was helping me, and at the end said I was "f**ing incredible" . I am passing some of that compliment back here. Again, thanks!!

@MattsGarageMiscDIY Жыл бұрын

Nicely done Juan!

@marleneparker8835 2 жыл бұрын

Thank You!! I love the way you teach! This 66 year old lady is going to fix her dryer she purchased for $100 dollars. I can do this with your video!! Thank you Matt!

@MattsGarageMiscDIY 2 жыл бұрын

Good luck Marlene, you’ve got this!

@marleneparker8835 2 жыл бұрын

@@MattsGarageMiscDIY I fixed it !!! Yea, just like you said to do. I am so happy. No more scary laundromat

@marleneparker8835 2 жыл бұрын

@@MattsGarageMiscDIY I fixed it!!! Yea

@MattsGarageMiscDIY 2 жыл бұрын

@@marleneparker8835 Nicely done, how satisfying is that? So happy the video was helpful :)

@melaniescott1355 Жыл бұрын

I can't thank you enough for your video! We were able to save our dryer and about $1,000 by buying a $220 replacement board. It's been a month now and the dryer is working perfectly.

@MattsGarageMiscDIY Жыл бұрын

Well done, always happy to hear someone saved money!

@jimschandevel5004 2 жыл бұрын

I had the exact same issue and resoldered it. Back in business in about an hour! Unbelievable! Amazon also has my replacement board. Thanks

@donaldosborne3669 9 ай бұрын

Matt, I have to hand it to you. I took out my old circuit board and Son of a gun the relay was burned exactly the same place yours was. We ordered another board and a it should be here tomorrow. Stay tuned to the results as I am 100% confident it will work when I get it back together. Edited next day I cleaned the post and got my solder gun and re did the solder job. Installed it back in the dryer and wellah all fixed. saved up over 200 for a job that took more time to get the board out than to fix it. KZfaq is the best. Thanks Matt

@MattsGarageMiscDIY 9 ай бұрын

Glad it worked for you. Imagine what you’d pay to have a repair person replace the board after labor and their mark-up on the part! Lot’s of people probably go buy a new dryer!

@wa4fat 4 жыл бұрын

Hi Matt - Thank you SO much for the well-done and informative video! Miracle of miracles, I was able to resolder the cold solder joints on the underside of the PC board and restore our dryer to service. Please know that my wife and I are tremendously thankful to you for taking the time to share your experience with others. God Bless!

@MattsGarageMiscDIY 4 жыл бұрын

Bill, well done, I wish that had been my outcome too, but always pleased to hear that someone was successful and saved some money too!

@maryao5396 2 жыл бұрын

Thank you so much for this excellent video! After watching it, my husband was able to replace the control board, with the exact same burnt connection. Our dryer works again!!

@MattsGarageMiscDIY 2 жыл бұрын

We’ll done, happy to hear about your success!

@stuartbertles8721 2 жыл бұрын

Im very thankful for your video! I ordered a new board on amazon for about $270. It will take a week to get but its better than $1800 for a new one. I appreciate folks like you and if you’re ever in orange Texas i will buy you a steak dinner!

@MattsGarageMiscDIY 2 жыл бұрын

You've got this Stuart!

@jimlavelle6337 3 жыл бұрын

Thanks, 2 years ago i used this to just resolver the lans, then i ordered the relay and tapped it to the back, today it went out again, so i replaced the relay and up and running. You saved me $$$. Thanks.

@ryanshahoud3660 9 ай бұрын

Thanks Matt! Your video helped me fix my dryer within hours of it breaking because of this issue. Now I have one less problem in my household to deal with and my wife is very happy (she never stops doing laundry). Not to mention the money I saved. You are the man!

@MattsGarageMiscDIY 9 ай бұрын

Ryan, glad to hear it you got it sorted! It’s always satisfying to fix something a save a ton of money especially this time of year!

@JeffreyEng1 Жыл бұрын

For anyone reading this in the future, I had the exact same issue as shown in the video and soldering that joint worked for my Whirlpool Duet with the board P/N: W10110641 Rev B. Thanks again for this video guide, you helped save my dryer!! 🙏

@Motocrossmikey 3 жыл бұрын

Thanks so much for this video. I was able to solder the burned area and it fired right back up. Make sure you clean the burned area down to bare metal before soldering.

@MattsGarageMiscDIY 3 жыл бұрын

We’ll done! Such a good feeling to fix something yourself and save a bunch of money.

@AllAmericanGuyExpert 3 жыл бұрын

Thanks! I fixed a WED9500TC1 (electric) that is essentially the same. There's a few more connectors, and removing the metal plate didn't work too well. But I had the exact same spot fried and did the exact same fix. It took 5 or 10 minutes to remove the main 2-pin connector that seemed like it was welded on. I wish I could solder like you ... mine is a mud dauber nest!

@johnmoore3883 2 жыл бұрын

This worked for me and the resolder did the trick no board replacement. It was exactly the same pin which is connected to a relay that turns on heavy amperage to I guess a motor. The board in the video looked more burned than mine but I'd bet the relay is still good just the trace got burned or fried. I small jumper wire to the two pins that it leads to would have probably brought the bad board back to life. At least that's what worked on mine but I didn't even need to add a jumper wire.

@stevencorreia725 2 жыл бұрын

My board went in the same location. Thank you so much for the fix, whirlpool wanted over $500 for a new factory board

@MattsGarageMiscDIY 2 жыл бұрын

Glad to hear it was helpful.

@stephengee8488 Жыл бұрын

Exactly the same issue. Same relay with blown soldered contact. Re-soldered and bingo, it worked. Thanks for pointing me in the right direction. Saved $100+ dollars on new board. You can also just order the relay that was blown and save a few bucks by soldering in new relay.

@MattsGarageMiscDIY Жыл бұрын

Stephen, in hindsight I wish I had kept the old board and tried soldering in a new relay. I believe there is a reason these blow, and either a new relay or board is the long-term fix. I’ve had no issues with the board now in several years since capturing this video.

@stephengee8488 Жыл бұрын

@@MattsGarageMiscDIY My thoughts exactly. I suspected the relay was blown and was ready to order another, but it was fine. Not sure why the connection would blow but relay fine. Drawing too much current through a weak soldered connection perhaps? We will see how long it lasts.

@jhartwells 3 ай бұрын

Just repaired my dryer using the tips from this video and the comments.... The hard part for me was getting the leg on the relay hot enough to accept the solder

@stephenwertz538 4 жыл бұрын

My dryer showed an F1 malfunction. Watch the video then went into the control board out when I did it show the classic signs that was shown in the video. I soldered a wire as shown in the video put board back in. it worked!! I'm quite shocked saving myself 150 to $200 on a control board

@MattsGarageMiscDIY 4 жыл бұрын

well done, congrats!

@stephenwertz538 4 жыл бұрын

@@MattsGarageMiscDIY thanks for the video was a great help. Mine look just like the video solder joint blown. Had it fixed in less than an hour and most of that time was looking for my soldering iron

@danielchaaban7291 Жыл бұрын

I know this is an old video, but my board was blown in the same exact solder joint as yours. 5 min of soldering later and my dryer is working again, can't thank you enough.

@MattsGarageMiscDIY Жыл бұрын

Well done Daniel, if you ever need to replace the board you will know it’s not that hard. Always glad to hear someone saved some money, especially this time of year!

@angelopellitteri8656 3 ай бұрын

Thanks for the video. I just repaired my dryer by soldering a jumper across the bad run.

@dtm8073 3 жыл бұрын

Thanks for the awesome video, I was able to fix my board. Actually I think mine was worse than yours, there was a small piece of the circuit trace missing. I had to solder a piece of wire between the pin and the trace. Wasn’t sure it was going to work and guess what, it worked! Dryer is back in action and the wife is happy!

@MattsGarageMiscDIY 3 жыл бұрын

Well done! In hindsight I wish I had kept the old board to try additional attempts to salvage it, but at the time was pretty happy to fix it with new parts without calling a repair person.

@laurawawa9849 2 жыл бұрын

We are going to try to repair, just ordered the same part you mentioned. Thank you for saving us $900 (the price for a new dryer)

@MattsGarageMiscDIY 2 жыл бұрын

Laura, you’ve got this!

@laurawawa9849 2 жыл бұрын

Question our part number is W10182365 and it’s not available we saw that yours was W10182366 not sure if the one we just ordered will work for our drier, since yours ended on 66 and ours ends on 65

@MattsGarageMiscDIY 2 жыл бұрын

Laura, the replacement part I used was W10174745, at the time I made this repair the research I did said this was a newer replacement part that was likely compatible with many previous models. That said I don’t pretend to be an expert on compatibility. The safest bet would be locating the model match on the board. The installation will be as you’ve seen in the video either way. Good luck.

@laurawawa9849 2 жыл бұрын

@@MattsGarageMiscDIY thank you. We cancelled the one we ordered and we are trying to find something compatible

@eugenelivar7069 2 жыл бұрын

Thanks for the video, repaired my dryer in a single morning! Very helpful!

@MattsGarageMiscDIY 2 жыл бұрын

We’ll done, always happy to hear the video was helpful!

@turtleinheat7615 Ай бұрын

I resoldered the pin, and it is working like a charm! Thank you!

@hopeyourehavingagreatday6740 2 жыл бұрын

You're the best!! Saved me from drying my clothes in the bathroom with a space heater 🤣

@MattsGarageMiscDIY 2 жыл бұрын

Glad to hear it was helpful! We’ll done!

@pomiller1972 Жыл бұрын

Just soldered up the bad spot on my daughter's dryer, I'll try it tomorrow

@lynnettepowell2101 4 жыл бұрын

Thank you! Thank you! Thank you! I followed every step and was able to solder the back of the control board and my dryer is working great! You saved me a lot of money.

@MattsGarageMiscDIY 4 жыл бұрын

That’s great! Even though that part didn’t work out for me, I was just as happy to swap in the new board and still save money by not paying someone else’s labor and mark-up on the part.

@popotit0 2 жыл бұрын

Hi Matt - Thanks for this video. I had exactly the same issue, but I just replaced the relay on the board ($9) and the dryer started working again. Seems like a design issue to me.... probably the designers saved 5c by not adding a diode or a high imp resistor....

@kerry4371 4 жыл бұрын

I have same dryer (11 years old now) I did the resolder on the exact component you did 2 years ago and it worked. Today the thermistor went bad, hopefully that's the problem.

@RC-tm8uc 2 жыл бұрын

Thanks a milliion! After I scrapped around the contact to remove the carbon build up, the soldering solution worked for me. I'll go ahead and purchase the new board since this appears to be an issue that will come back in time, but it keeps things going in a pinch. Really appreciate your time to provide the info.

@MattsGarageMiscDIY 2 жыл бұрын

we’ll done, glad this helped you!

@Jeff_Pendleton 2 жыл бұрын

I soldered mine also and got it to work. Exact same joint. The solder did not seem to want to flow in there all that well. and I did clean it first and use flux. But it is working...right now anyway. And if it fails again, now I know what to do. Couldn't have been much easier to access. Thanks for the video. BTW other viewers, that part is around $300 with tax. Worth a shot!

@Gena9evr 9 ай бұрын

Thank you Matt! I am a complete idiot when it comes to working on or fixing anything. I mean a complete zero. I don't like to do it. I'm not the MacGyver type. That said, I decided that I would try fixing my own dryer as money's a bit tight. If you follow this video step by step, order the exact part that Matt recommends, take pictures to make sure you know where all the plugs go, then like me, you too can do this. It takes about an hour and a half after you get the part (Recommendation: Follow Matt's directions on how to pull the board and see if it blew out...my blew EXACTLY like and had the same burn mark as Matts). To fix: It's really just unscrewing bolts and screwing bolts back on and unplugging and then replugging plugs. First start by 1) removing the top of the dryer (that's all that's required...you don't need to take the back dryer panel off, you don't need to remove the drum, and on and on...just a few screws on top of the dryer to remove the top of the dryer), 2) follow Matt's video on how to unplug (and then later re-plug) the pieces from the board, and 3) remove the old mother board. If like in the video, the board has a burned spot, then move to 4) buy the new board (I just bought the exact one Matt had in this video's comment section from Matt), 5) plug in the new mother board, 6) re-secure the top, 7) re-tape the air vent and 8) turn the dryer on. It works just like new! Amazing! (This video really shows a novice how to do this step by step.) The new board (with inflation) cost about $250. But that's better than $1,000 for a new dryer or $400 for a service person and then an additonal $250 for the board on top of the service fee. If I can do this, you can do this! Good luck. Matt's awesome! KZfaq is awesome too for creating the platform for video sharing!

@MattsGarageMiscDIY 9 ай бұрын

Always happy to hear that someone was able fix something themselves and save money! Thanks for the kind words.

@livefreedom1776 3 жыл бұрын

Thank you for this video I was able to fix my dryer by soldering the control board! Awesomeness

@MattsGarageMiscDIY 3 жыл бұрын

Well done, you saved a good deal of money, go treat yourself to something good!

@Peter-hf8xn 3 жыл бұрын

Thank you!!!! Save me about $250 I was able to solder my connection you are the man!

@MattsGarageMiscDIY 3 жыл бұрын

Awesome, we’ll done!

@jjmnz 10 ай бұрын

Thank you Matt! As others posted, I had the same issue and similar burnt spot. Now to order the replacement board.

@MattsGarageMiscDIY 10 ай бұрын

Glad it was helpful, you are halfway there!

@matssundin1292 2 жыл бұрын

Cant express enough thanks for this. Had exact same problem and fixed it in less than an hour. Amazing and so happy dodnt need to buy new one. God bless you and your family 🙏

@franksflytraps 3 жыл бұрын

you just saved me a shitload of money, thanx. Same problem, resoldered joint and is working good so far!

@jeremycullen63 2 жыл бұрын

Soldering worked for me. I had to clean the circuit board before soldering it.

@MattsGarageMiscDIY 2 жыл бұрын

We’ll done Jeremy!

@brettbonifay9620 4 жыл бұрын

Great video. Exact same solder joint blew on my control board. Lucky enough that resolder worked!

@jeffh6686 3 жыл бұрын

Great video. My parts are ordered and Ill replace instead of the repair guy. Nice job on the video.

@edreed9519 3 жыл бұрын

Matt I want to thank you very much for this video. You provided every detail I needed. When I took out the controller the burn mark on the panel was identical to your example in the video. I was on hold with Whirlpool Canada and it was taking some time so I though ok he tried a solder so I would as well. Still on hold plugged stiff back in and bingo works like a charm.

@MattsGarageMiscDIY 3 жыл бұрын

Ed, always glad to hear this was helpful!

@pierreorcel6296 2 жыл бұрын

Perfect direction... THANK UUUUUUU by the part from Amazon for $257.... Whirlpool had it for $404

@jkemeyer75 Жыл бұрын

Big thanks for this video. Blew out one of the solder joints from the same relay and was able to fix.

@saulgoodman9657 7 ай бұрын

Thank you for this video! In mu case just soldering the relay helped. 15 minutes and my dryer works!

@MattsGarageMiscDIY 6 ай бұрын

Fantastic!

@nickg1584 2 жыл бұрын

Awesome video!!! I wish all videos intended to be helpful were like this.

@CraigMatsuura 3 жыл бұрын

You rock this video and another helped out. Saved me from buying a board as soldering was the trick. Tested with a multi-meter that there was a bad connection on the trace to the post that was burnt. crapped the trace to make sure there was a connection. I almost added a new wire to replace the trace (maybe I should have). But it seemed to work. Had this not worked I would have order that control board.

@MattsGarageMiscDIY 3 жыл бұрын

Always glad to hear someone saved money!

@ZagDrag 2 жыл бұрын

Thanks for the help! Saved me a lot of time and struggle.

@jefffriesen8796 2 жыл бұрын

thx very much. vid still helping after 3 yrs.

@scottw2157 3 жыл бұрын

Amazing job. You saved me the cost of a new dryer. Thank you.

@MattsGarageMiscDIY 3 жыл бұрын

Nice job Scott! Glad you got it handled, very satisfying to save that kind of money right!

@juice6795 4 жыл бұрын

Thank you for the video . Saved us from purchasing a new dryer .

@MattsGarageMiscDIY 4 жыл бұрын

so glad it was helpful.

@Silverdragon517 10 ай бұрын

Very helpful. Just ordered the part from Amazon. Thank you

@MattsGarageMiscDIY 10 ай бұрын

Glad it helped

@billwilson200093 4 жыл бұрын

Excellent. 5 min job. The parts pretty expensive unfortunately Great video

@MattsGarageMiscDIY 4 жыл бұрын

Thanks Bill, still considerably cheaper than also paying a service call with labor, and the mark-up on the part, or worse yet buying a new dryer. Hope you can get more miles out of your current dryer!

@linhlieng8538 3 ай бұрын

Thank you! Awesome video and provide much needed info. Cheers

@johnnyViDeO Жыл бұрын

Well done, EXCEPT warn viewers to unplug the unit before taking the top off!!!

@MattsGarageMiscDIY Жыл бұрын

If you read my detailed description I call out unplugging the unit before moving it away from the wall. I typically try to capture additional information in the written description. This goal of the video is to share the level of effort, tools and parts I used. This might be enough to give some the confidence to tackle this repair on their own, for others maybe not. Best of luck with your repair.

@brahmabob1225 2 жыл бұрын

Oh, yeah! Perfect video for my needs. Saved me some serious cash, my friend!

@MattsGarageMiscDIY 2 жыл бұрын

Always happy to hear someone fixed it themself and saved money! We’ll done.

@threxBox 4 жыл бұрын

dude, this was perfect. i even had the burn mark. Fixed. THANKS!

@MattsGarageMiscDIY 4 жыл бұрын

Glad it helped, and super satisfying to fix something yourself and save money!

@titopascua3225 2 жыл бұрын

Many thanks making this video I was able to solder mine and it worked

@remylebua1 2 жыл бұрын

Ho man I did same thing following your steps and holala I didn't my self Thankyou a lot for this video

@DJBossCreations 2 жыл бұрын

Thank you so much mine just started this f01 yesterday you're awesome!

@johncarruth904 3 жыл бұрын

thanks for the pointers, they were a tremendous amount of help

@MattsGarageMiscDIY 3 жыл бұрын

Glad it helped!

@joeriver1562 4 жыл бұрын

Thank you sir! You have saved me a lot of cash, especially in these times of need

@MattsGarageMiscDIY 4 жыл бұрын

it’s empowering to fix something yourself, and saving money is always great, glad it helped you.

@ema5944 4 жыл бұрын

This was awesome!!!! Thank you so much, you just saved me several hundred dollars.....great video!!!!

@MattsGarageMiscDIY 4 жыл бұрын

I love saving money and the satisfaction of fixing it yourself is pretty nice too. 👍🏼 Glad it was helpful.

@Yortreske 3 жыл бұрын

Got me some brownie points with the Mrs. thx dude

@MattsGarageMiscDIY 3 жыл бұрын

Nice work Troy!

@meffagirl 3 жыл бұрын

Thank you so much. This helped me tremendously

@MattsGarageMiscDIY 3 жыл бұрын

Awesome Laurie! It’s always nice to get feedback that a video has been helpful :)

@richardbeckman8523 Жыл бұрын

Worked for me. Hope it holds up. Thank you!

@bryanborough3260 2 жыл бұрын

This was exactly my problem, only I just replaced the component on the board that burnt out - G8P-1A4P-12VDC Fully-Sealed PCB Relay 30A 250VAC - 12 dollars on Amzn. Resolder may not work - solder on a new relay as the old could be burnt out. Solder iron and solder is cheap. I had tested fuse, pully switch, door switch, etc. Then took out the manual, saw how to get it into diagnose mode, and saw the F01 fault code (bad control board) message. Found this video. That board is 200 plus bucks. Why not just replace the bad component? I still see the F01 code, but the motor now kicks on. Maybe there is a way to clear the fault codes? Thanks for the vid!!!

@MattsGarageMiscDIY 2 жыл бұрын

Bryan. We’ll done. I wish I had kept the old board, I’d give the relay replacement a go and keep it as a backup. At the time I did this I was simply trying to fix it fast and fix it to last. I was already satisfied in not calling a repair person who most certainly would replace the board and charge me labor and markup the part. My dryer had been running flawlessly for nearly 2 years since until I had to fix another issue just recently when my thermal fuse failed. Video posted on that one too for reference :)

@davidsouthall6789 Жыл бұрын

damn inflation.... now this part is $223 on Amazon. I'll check around - thanks for video!

@MattsGarageMiscDIY Жыл бұрын

David, I’ve seen the prices swing pretty dramatically based on supply, many independent sellers on Amazon, for sure shop around a bit. Good luck!

@amaterasu48 2 жыл бұрын

I think you could have wired the circuit and fixed the board. That said, great work fixing it!

@MattsGarageMiscDIY 2 жыл бұрын

I wish I had kept the old board to give it a try, some have been successful replacing just the bad relay. In the end I am still very happy to have fixed it myself, saved some money. A repair person most likely would’ve replaced the board at a much higher cost plus labor. I hope this helps you tackle the job and save some money too!

@hesamm3509 3 жыл бұрын

Thank you for your help board was w10182366. Fixed it by soldering just like your video.

@yvansflorian8944 19 күн бұрын

Thanks so very much

@deeanthony5431 2 жыл бұрын

July 11 , 2022 Just tried this same model , re-soldiered connection on board , now good until who knows when . Thank you God bless 👍🏿

@sprinkleroadhome3559 4 жыл бұрын

Thank you for doing this video, I was able to do this by myself and get it fixed.

@MattsGarageMiscDIY 4 жыл бұрын

Well done, so glad it was helpful!

@Agius_Jozef 2 жыл бұрын

This is a great video.Thanks Matt.

@garynowlin8883 5 ай бұрын

The power lead burned out on the power board relay. The trace and pad was burned away. You can fix with a soldering iron and small gauge wire. You solder the wire to the damaged lean and jump it over following the trace to the next lead. No need to remove relay at all since it is not damaged.

@ryanrunangnaff2868 12 күн бұрын

Do you know how to take this out. I don't want to break it. It doesn't fill it will come out.

@cmakely60 4 жыл бұрын

Great video, thanks

@davewolfe5169 3 жыл бұрын

Thank you so much

@stiffisticated-6820 2 жыл бұрын

Well done 👍.

@danielfiddler5014 3 жыл бұрын

Thank you for sharing sir! 😎🙌🏼

@meagankozak-sg8yf Жыл бұрын

Wondering if you might be able to answer my question 🙃 I did all the steps, resoldered everything together and then a different part on the board blew and started smoking when I went to try and plug my dryer back in! Any tips??

@MattsGarageMiscDIY Жыл бұрын

Meagan, my hope in soldering the board was that it’d be a temporary fix while I ordered a replacement board. For me Soldering it didn’t work either. My advice would be to order a replacement control board, this is still far cheaper than buying a new dryer or paying someone else to service it (and replace the board). Best of luck.

@kellimack5478 11 ай бұрын

I had the burnt spot on my WED9500TW3 Duet. Do you know why it blew in the spot? Thanks for the great video! I have a new CP on order.

@MattsGarageMiscDIY 9 ай бұрын

I don’t know why this is the weak link on the board, possibly it’s by design, but know it’s very common. I hope you were able to successfully get your dryer back in service!

@kellimack5478 9 ай бұрын

@@MattsGarageMiscDIY thank you for the reply and info! I found a board for $175. It was easy to replace.

@Philippians_4_6 4 жыл бұрын

Bought and installed new control board however it beeps 3 times when trying to start. Help!!!

@MattsGarageMiscDIY 4 жыл бұрын

I have not had this issue on my dryer, but have read that the door switch may be the cause of the 3 fast beeps/no start. try checking that the door close switch is clicking when you close the door. The light inside the dryer will shut off. With the dryer door open you can push the switch in and see if it is working, and even test start the dryer. Hope this helps.

@ronaldcabrera2577 3 жыл бұрын

El fusible que está lado en la parte de abajo ese se lo debe medir en continuidad si vale o no

@LeChat582 Жыл бұрын

To fix the electronic board you need to replace the bad trace by adding wire

@interstatebullly3nyg551 11 ай бұрын

These dryers have the option to use electric or gas dryer setup correct ??

@MattsGarageMiscDIY 11 ай бұрын

No. But a gas dryer still needs electricity to spin the drum and ignite the flame.

@janapellusch9339 3 жыл бұрын

Question about the part that blew the connection: one reader calls it a resistor, another a relay. It’s rated at 30 Amps, so I’d call it a fuse. 🤔 Is it usually the same component that blows? On mine it is the black rectangular shape, top left, second from left. Is there a potential problem if you resolder and re-use it? Thank you.

@MattsGarageMiscDIY 3 жыл бұрын

Jana, I wish I had kept the old board. Would be worth a try to just replace the relay, but I have not done this, only researched it after I had replaced the board. This may be the part you need: amzn.to/3ovXpxe

@worldfact6741 4 жыл бұрын

Dryer model number YWED9300VU0 Actual control board number :w10182366 As the web , this is the new number that replace the old number : WPW10174745 I changed it , it was running but I got L1 error and got no heat

@fernandoochoa686 4 жыл бұрын

Hello friend, what is the price of this spare? Thanks

@MattsGarageMiscDIY 4 жыл бұрын

$152 for the Tire, $73 for the new steel wheel. The goal was to get something more stable to fit. For me this is cheap insurance because I take this vehicle places where tow trucks are not an easy option. Good luck.

@Allmuf 4 жыл бұрын

Thank you, I just resolder the relay on the board and its back to business! Save a lot of money!

@thndr_5468 3 жыл бұрын

How did you remove that orange part?

@stevewilson7857 4 жыл бұрын

I like the video but for $11.00 you can replace the resistor. Not that difficult to do but if money is no object then replacing the entire board is the easiest.

@MattsGarageMiscDIY 4 жыл бұрын

If money is no object you call a repair man and pay them the labor and part mark-up too. You should create a video of the resistor replacement, that’d be cool for those that wanted to try that first and save some serious money!

@janapellusch9339 3 жыл бұрын

Steve Wilson you bring up something I’ve been thinking about. Clearly, something blew out on the board and the solution is not simply to resolder the connection. I did not know the part was a resistor, but whatever it is, it needs to be replaced. Otherwise ... who knows what?

@stevewilson7857 3 жыл бұрын

@@janapellusch9339 I’ve actually replaced this twice over the years. Just buy a desolder kit and you can do it yourself. Trust me I have limited skills :). Here is the part: G8P-1A4P-12VDC Fully-Sealed PCB Relay 30A 250VAC for PC Board or Panel-Mounted. It’s a relay that just blows after repeated use. You will see on the circuit board where it just decided to fail. The resistor is held onto the circuit board by tiny dots of solder. The desolder kit melts and suctions the old solder away. Good luck!!!!

@stevewilson7857 3 жыл бұрын

@@MattsGarageMiscDIY Good idea Matt I will make a video (if it happens again). As I mentioned to another person I have limited skills but all I needed was patience and a desoldering kit and of course the new relay :)

@mississippisawyer9733 3 жыл бұрын

Per Matt’s Garage and Misc. DIY request in his reply to Steve Wilson’s comment, here is a link to a video of someone repairing a similar dryer with the same error code by replacing the $11.00 resistor: kzfaq.info/get/bejne/l8CHdc2g2qq0pas.html&feature=share

@AriesBaller14 4 жыл бұрын

Hi, after Googling I've gotten numerous ways to check for error codes. So far, two different ways with two different results. Can you tell me how? I'm pretty sure mine could be the same problem, but my lights aren't blinking like yours at the beginning. I'm just trying to save myself some time and unnecessary expenses. Love your video! Thanks!!!

@MattsGarageMiscDIY 4 жыл бұрын

Mandy, I'm honestly not an expert here, just captured this video to share that I was able to fix this specific error code and how I did it. Are you getting an F01, or just having issues but no error?

@AriesBaller14 4 жыл бұрын

@@MattsGarageMiscDIY my dryer powers on and when the start button is pressed it will click like it's going to start, a second or two later it'll click again, but it just never starts. I had it powered on and held the Start button for a few seconds and got an F01 code. However, if I do a code check by pressing the Manual Dry up and down arrows consecutively I get an F50 error code.

@sandyorloff8760 Ай бұрын

What type of solder do you use?

@MattsGarageMiscDIY Ай бұрын

Sandy, keep in mind my attempt to solder failed, but I was using what I had which is a 60/40 rosin core solder that I typically use when repair ing guitars… best of luck in your repair!