Thank you for this video, I was having the same exact issue with the code coming up, and also I figured out what caused the board to fault out, some how over the years the sheet metal that the board is attached to came loos on one end and was dragging on the spinning drum, it would appear during assembly of the machine they slipped the end into the proper slot on the front side of the machine but on the back end it looked like they used a sheet metal screw on the underside of the board mount as opposed to installing the board on the upper side like the front and over time the screw backed out and the Board mount fell directly onto the spinning drum, of which I wonder what was making that horrible noise during operation, but now two issues resolved, again thanks for this post, these are the videos I like a lot because they really help folks out a lot specially since we don't have the money for a new machine, and why buy a new machine when this new part I just ordered will make it like new, and no more noise!! 👍👍👍🔧🔧.
@504ksh3 жыл бұрын
Thanks for talking us through. Details are key 🔑 to subscribers
@harvestblades3 жыл бұрын
A common failure on the control board is a small relay that costs about $10 vs the $225 or more control board. It can be replaced with a simple soldering iron & solder sucker. There are some well done videos detailing that fix.
@tn71983 жыл бұрын
Could you share a link to one of those vids? Thanks
@dustins41942 жыл бұрын
link to the video? Thanks!
@rotcod28862 жыл бұрын
That's what I thought too. I did one of those fixes about 10 years ago. It cost me a $20 soldering iron.
@rotcod28862 жыл бұрын
kzfaq.info/get/bejne/sLmKi8Z3zZywpnU.html
@interstatebullly3nyg55111 ай бұрын
It’s a video that’s about 4years old and 35 minutes long not many out there that go into that much detail great video I recommend it
@tn71983 жыл бұрын
Try unplugging and plugging in to reset it. Worked for me. I'm on my second control board on this unit, replaced a couple years back. I wouldn't be surprised if i need to replace again, but this got me moving again at least for now.
@basilhamilton95287 ай бұрын
Thanks found the burn marks on the backside when I pulled the board out. Wish I had read you had parts. I would have ordered from you instead of eBay. Thanks though!!
@JohnAnderson-sm8jl Жыл бұрын
Hey genius...you should remove one screws on the metal panel, which allows you to lift the whole thing off, and give you easy access to the screw holding the circuit board box.
@jeanellmoon95482 жыл бұрын
Thank you for the video. Very informative I also like the 90 degree screw driver.
@fish07413 жыл бұрын
Title say's Washer, You need a cup of coffee to wake up like me. Keep up the Good Work
@BeardedApplianceRepair3 жыл бұрын
Got it fixed. Appreciate that!
@jeffbushdesign Жыл бұрын
Great video, what kind of camera do you use to take this videos? It's great you can see everything you're doing with your hands
@leokarawa43543 жыл бұрын
Coolest tech on here. Thanks 🙌🏼😎
@smilemm46123 жыл бұрын
We get it you like that tool
@dandever342511 ай бұрын
Thank you for your help.
@jm1551701 Жыл бұрын
OK I replaced that part with a new one, the machine came on as it should ran through the cycle and now I am getting the F-70 code again and machine won't even turn on!! getting very frustrated ! what else could it be, is it the Mother Board ??
@bnieves100 Жыл бұрын
Great job thank you so much
@garynowlin88835 ай бұрын
Easy to just repair board if you have a soldering iron
@franklynordz40302 жыл бұрын
What’s the part # number and how much it cost and where do I get it
@davidbuchanan5875 Жыл бұрын
What if you have no power to the board....heard a pop while running and then no lights ...nothing
@marydewitt49772 жыл бұрын
What is the part number that you purchased FOR THE JOB
@lwebster373 жыл бұрын
Hello thanks for the video. My question to you is how much is one of them control panels at Lowe’s? You mentioned the $50-$60 extra because the core. And I will get that back when I return it Thanks!
@BeardedApplianceRepair3 жыл бұрын
You cannot get parts like that from lowes. You will have to find a local appliance parts store. You should have one somewhat close. I have one in my town and three more 20 miles away. They will have a cost for you just call them with a model number. My guess is $200-$250
@albafitipaldi9731 Жыл бұрын
@@BeardedApplianceRepair hi How Can I found model number? Thanks for the video
@dotalber8775 Жыл бұрын
Replaced control board but still does not run??? Help
@ronjones4691 Жыл бұрын
How much does a board calls and what’s the name of the board?
@senseizay60166 ай бұрын
How do I check for code
@bayardtaylor2990 Жыл бұрын
How was the control board
@danny21313 жыл бұрын
How do you put it in diagnostic mode to find the code I have a whirlpool electric dryer wed9400suo
@68ninja113 жыл бұрын
How do you know you have it I just bought these used it's not working
@davidnavia21732 жыл бұрын
Excelente video donde puedo comprar la placa
@user-qc6lm2wv2t Жыл бұрын
How much does it cost
@jrdifferent3 жыл бұрын
Do you know the part number for this control panel? Thank you
@BeardedApplianceRepair3 жыл бұрын
Go to your local appliance parts store give them your model and they can get you the number even tell you how much it may be. I would have linked it if there weren't so many of them.
@DIRTPUNKZ862 жыл бұрын
The real question is why is this such a common problem?
@BeardedApplianceRepair2 жыл бұрын
When these wear built they were only designed to last maybe 7-10 years.
@AndyEmerson86 ай бұрын
I did this and now I have a F70 code!!
@tyylerduurden11 Жыл бұрын
Can a pf code also be a bad board?
@BeardedApplianceRepair Жыл бұрын
No That is a different problem. "pf" Means power failure. This happens if you simply unplug it and plug it back in. Or if your power goes out and comes back on. Usually it is simply that. You unit should work fine.
@rotcod28862 жыл бұрын
Here's how to fix it for the cost of a soldering iron, which can be had for $20!! kzfaq.info/get/bejne/sLmKi8Z3zZywpnU.html