Had to get the Right hand bracket to mount the prop valve in order to get clearance for the brake lines BEATS BY: CRANK LUCAS
Пікірлер: 28
@ryanmiller95892 жыл бұрын
Where’d you get the red brake lines??
@PENNYLS12 жыл бұрын
instagram.com/finishing_lines?
@jarrettslee12 жыл бұрын
Nice!
@jeromeswaby52612 жыл бұрын
Question if I want my rear breake to luck before the front for drifting where should I connect the valve to the rear side of the master cylinder or the front?
@bigmoe99725 ай бұрын
Bro what size lines and length are you using from brake line to proportioning valve
@PENNYLS15 ай бұрын
Size 4an. (2) 27inch and (1) 30inch. I had them custom made. I’ve since changed my setup tho
@bigmoe99725 ай бұрын
@@PENNYLS1 what did you change to?
@PENNYLS15 ай бұрын
@@bigmoe9972 After trying two different Wilwood m/c I switched back to the factory one did the rear disc swap also. kzfaq.info/get/bejne/pbyidKmpmrTFiGw.htmlsi=aaa5BeC17jWvy-cO
@bigmoe99725 ай бұрын
@@PENNYLS1 so the wilwood prop valve didn’t work for you as well
@PENNYLS15 ай бұрын
@@bigmoe9972 not the prop valve but the master cylinder, I couldn’t get it to bleed properly.
@terrybenton4137 Жыл бұрын
What’s the part number for pressure valve should it say drum brakes or does it matter
@PENNYLS1 Жыл бұрын
The red one is for drums. They have a blue one that’s for disc in the rear. Wilwood Residual Pressure Valves 260-13784
@WrenchnWitWillieG2 жыл бұрын
Do you have part numbers for all the fittings and lines you used?
@urnew Жыл бұрын
They sale kits online 3/16 break line kit 1/4 break line kit Order some 90 degree fittings as it will help
@jiambruno12 жыл бұрын
were could i by the fitting adapter goes to rear line please
@PENNYLS12 жыл бұрын
#BQ261 3/8-24 MALE TO 9/16-18 FEMALE ADAPTER (IS) www.dmpfasteners.com/index.php?main_page=product_info&products_id=13814
@cashcountystreetcars Жыл бұрын
Where did you get the 9/16 to 3/8 adapter I can't find 1 anywhere
@PENNYLS1 Жыл бұрын
I keep this link on my notepad lol. www.dmpfasteners.com/index.php?main_page=product_info&products_id=13814
@cashcountystreetcars Жыл бұрын
Thanks
@cashcountystreetcars Жыл бұрын
My line adapters ame in but won't screw on ... had to use a coupling instead I have a 80 bu it should be the same right ?
@PENNYLS1 Жыл бұрын
@@cashcountystreetcars mine screwed right in. Yours could be different tho
@Bball1284 ай бұрын
@@PENNYLS1which one did you order because I ordered one but the male end is 3an and I think I need 4an
@ericchavez60532 жыл бұрын
What's the point of the pressure valve?
@PENNYLS12 жыл бұрын
Since I still have drum brakes in the rear and the Wilwood prop valve is for disc to disc. The pressure is needed to keep the proper amount of pressure towards the rear for the drum brakes. If you have disc brakes in the rear it’s not needed.
@ericchavez60532 жыл бұрын
@@PENNYLS1 dam didnt know this, i have seen so man people install these without that pressure valve.
@PENNYLS12 жыл бұрын
@@ericchavez6053 it could be they have disc brakes in the rear or the simply didn’t know. They will find out fast tho lol