Make sure to subscribe! / dummyround / dummyround www.paypal.com/paypalme/dummy... / dummyroundofficial rumble.com/user/DummyRound dummyroundreloading.com/ Send things to: PO Box 30115 Clarksville TN 37040
Пікірлер: 54
@kendalls3dcustoms5993 ай бұрын
Excellent!! Thanks again for the link and everything!
@DummyRound3 ай бұрын
No problem! Let me know if you have any other questions
@jamespollard1670Күн бұрын
Apply some wheel bearing grease to the return spring gets rid of the squeak.
@azazelakira12 Жыл бұрын
Good hobby right here
@DummyRound Жыл бұрын
Very relaxing👍🇺🇸👊
@ggwoutdoors2a Жыл бұрын
Titewad, wad wad, you had me rollin! good stuff DR 👍
@DummyRound Жыл бұрын
🤣glad someone caught that
@cameronlamb72743 күн бұрын
Challanger hulls are cheddite so are score for the most part early on score did use a different hull.
@cameronlamb72743 күн бұрын
Stuff like Winchester universals are great for loads where you don’t mind loosing a hull in the woods. I find a lot of older style AA’s at gun shows or on classifieds I was just given a huge tote worth of hulls and in there is probably half full of red and silver AA compression formed.
@anthonyflannery49958 ай бұрын
BPI has a tool to tighten up the primer pocket. I thought my load all was the only one that squeaks lol
@DummyRound8 ай бұрын
Might try that one day but I have enough hulls for now, and only euro primers so I'm not worried about trying to make the domestic primers fit. I've since lubed up the ole load all, but they do make some noise lol🇺🇲👊
@jesseboutdoors Жыл бұрын
I got a lee load all now. Now I need to figure out this different wad thing 😂
@DummyRound Жыл бұрын
🤣 it's a giant rabbit hole... what hulls are you starting off with?
@DummyRound Жыл бұрын
Might be able to send a variety of wads with your lead👍
@jesseboutdoors Жыл бұрын
@@DummyRound thanks 👊🇺🇸
@cw2a Жыл бұрын
🤟🏽🤘🏼🤟🏽🤘🏼🤟🏽💪🏼👍🏼
@DummyRound Жыл бұрын
👊🇺🇸👍
@tacticalrabbit308 Жыл бұрын
Pellet in the hole it's call the gold pellet
@DummyRound Жыл бұрын
Yessir!
@DPCoonTrapperАй бұрын
Yes king!
@jasonlovi874515 күн бұрын
How much heavier is the shot charge with #7 shot? The loading manual says the bushings are optimized for #6 shot and anything smaller will produce a heavier charge.
@nickjm37fordel1 Жыл бұрын
What will speed your loading up would be to just put the hull in the station and not try and slide it up on the stem and hold it while you bring it back down, that's wasted motion and slows you down. Enough practice you can pull the handle down over the hulls and I think you will find that a lot less tiring.
@DummyRound Жыл бұрын
I'll get more gooder in time. I'm just trying to make em correctly right now 😂
@tims6212 Жыл бұрын
Oh some gratuitous shot gun loading! Sweet vid bro.
@DummyRound Жыл бұрын
Yessir! Thanks🇺🇸👊👍
@jamespollard1670 Жыл бұрын
You may want to save some of that 7-8 shot to make some buck shot , unless you really need some trap loads . I myself prefer a more potent load than trap loads . BB , 00 buck and slugs are my preferred loads .
@DummyRound Жыл бұрын
I've got two buckshot molds I need to break in and get a bunch of cast up, #4 and 00. Going to use range scrap, add a touch of linotype and quench after powder coating. I'd like to get the little HF drum tumbler to smooth out the buck shot before PCing. How hard do you actually need the buck shot to keep from deforming? I'll be using BPI original buffer and probably not magnum loads. Just going to copying the military 9 pellet 00 1200fps load. Thanks! 👍👊🇺🇸
@jamespollard1670 Жыл бұрын
@@DummyRound I use good ole wheel weights or recovered shot for buck shot and water quench . I don't worry about getting them perfectly round . My thought is , they'll deform when going through the choke anyway .
@johnoakley5544 Жыл бұрын
I know putting a roll crimp on the newer Winchester "western" hulls will cramp your hand fast. they are definitively a different polymer. I have been thinking about getting into shot shell reloading. just more money haha
@DummyRound Жыл бұрын
I just started and I'm balls deep in it already, might as well pick up a drill press for my roll crimper😂
@johnoakley5544 Жыл бұрын
@@DummyRound 🤣🤣🤣
@DummyRound Жыл бұрын
And what was that tool you used to cut the crimp off your bird shot and turn into a slug? I need one of those, too😉
@johnoakley5544 Жыл бұрын
@@DummyRound I bought a few from the old eBay. Just called a shot shell crimp removal tool. Most are just 3d printed like the brass jigs but work great. Uses replaceable utility blades. Then I upgraded to a bench mount Forrest camping 12g roll crimp tool(trust me your hands will thank you). Or just spend the same and get one that goes in a drill press lol.
@DummyRound Жыл бұрын
I'll have to get one of those, for shenanigans and such
@allthingsconsidered3211 Жыл бұрын
Did u also get a lee slug mould? Id love to see a video on slug reloading!
@DummyRound Жыл бұрын
It's on the never ending shopping list!
@jamesboland60726 ай бұрын
What size bushings are you using
@DummyRound6 ай бұрын
The smallest recommended charge for any given powder per payload👍🇺🇲
@Sneakyjoe699 ай бұрын
What shell holders are those
@DummyRound9 ай бұрын
Lee 50BMG loading block
@Sneakyjoe699 ай бұрын
Do you have a block you recommend for 20 gauge ? Do you use that only for 12 gauge ?
@DummyRound9 ай бұрын
It'll work for 20ga pretty well, too👍🇺🇲
@Jim_Wilde7 ай бұрын
imho wasting of time I did 20k+ with MEC 8567N and pretty happy because an hour and I got 200 rounds. this press only for 25-50 rounds and you wont shot them because your sweat stick it to your ammo bag :))) If like this single stage I'd rather buy a cheap ammo than do this job.
@DummyRound7 ай бұрын
Yeah, the Lee is pretty slow, but it's great for Buck and slugs. I've since gotten a 600jr and it's in a whole new league🇺🇲👍
@Jim_Wilde7 ай бұрын
@@DummyRound One problem of MEC it is to big you have to have reloading room for that. And Lee cheap as dirty I agree if 20-100 rounds per month I can bear slow process of it but if 200 per week buy ammo or progressive any press IMHO
@timberboy19845 ай бұрын
So I run a pw800 and a lee load all 2 and to be honest I personally prefer the shells load out of the lee vs my pw. I also can do one off test rounds.
@DummyRound5 ай бұрын
It is great for testing and small batches 👌
@Jim_Wilde5 ай бұрын
@@timberboy1984 I bought Lee 20Ga as well and reloaded for a small project about 300, not bad for this price it is unbeatable. After I do roll crimp.