Wire To Stub Shaft Connection Using J-B Weld Oxidean Mini-Dom Mini Mono

Рет қаралды 1,481

Ай бұрын

RTR FIBERGLASS MINI DOM
oxideanmarine.com/products/co...
3019 M4 (BRONZE PROP)
oxideanmarine.com/products/rc...
3219 M4 (GOLD PROP)
oxideanmarine.com/products/co...
3316 m4 (red prop)
oxideanmarine.com/products/cn...
SMC HCL-HP Flight Series 14.8v 2200mah 80c Lipo
www.smc-racing.com/index.php?...
TURN FIN BRACKET - PROP BOX
rwarden@gmail.com
Thanks for Watching Ironclad Rc Tinker test and tune everything
Personal contact information ironcladedout@gmail.com

Пікірлер: 35

@holgerlafrenz2895 Ай бұрын

Thanks Big B for more tricks of the trade!

@ForestPettit-jb7jl Ай бұрын

Damn! That thing rips! Thanks again for all the tips..

@scaleworksRC Ай бұрын

Good ol' JB Weld saves the day.. again! 🦾BG4L🚤💨

@norcalrc Ай бұрын

Welcome back to Big B’s down home repairs dun rite

@im2tall1 Ай бұрын

I think I got the Quik Steel tip from you....That stuff permanent !!

@55steviegreene Ай бұрын

Had the same thing happen to mine. great video

@michaellucre8249 Ай бұрын

Had the same issue as well, I filled mine and was going to re drill the ID…I ended up buying a shaft from aliexpress and yet to run it due to the frustration of getting a boat that didn’t work out of the box

@IsaacSchultz-lz8jc Ай бұрын

You should look at the Bancroft jet power sprint boat a 25inch brushless jet boat

@M14armorer Ай бұрын

Silver solder is the way to go IMHO

@holgerlafrenz2895 Ай бұрын

That's what I was thinking. Or solder but silver solder would be best.

@DDRDK Ай бұрын

@holgerlafrenz2895 if you order a propshaft that comes with a 1/4" flex cable already attached from say MHZ. What are they typically using? Always wondered what pre prepped bigger stuff comes attached with.

@IRONCLADRC Ай бұрын

Thought about it but the heat may weaken the stainless steel wire. I've brazen wire in the past and got it to hot and the wire bent.

@DDRDK Ай бұрын

@@IRONCLADRC I wonder what the common practice is for the bigger 1/4 cables with the big people like MHZ or someone. When you order it assembled I'm not sure what they do. Just getting into boats after being into rc for over 20years. Got my first hull a 70" SV50 so still trying to learn before I build it up.

@nealstarling5422 Ай бұрын

👍👍👍

@brentonbaxter8593 Ай бұрын

I would use loctite retaining compound

@artpeck9272 Ай бұрын

I don’t know B, dang if I wouldn’t set it up in the drill press and put hole through that collar and shaft and insert a pin. It would be tricky, very small bit, but at the price of props, I’d think it’s worth the hassle.

@IRONCLADRC Ай бұрын

Drilling a hole through this wire would be almost impossible IMO and may weaken the wire?

@artpeck9272 Ай бұрын

@@IRONCLADRC it could weaken the wire for sure. I’m just trying to think of some way to have some sort of retainer. I guess the best thing is to check it routinely. Looks like some heavy weather rolling through our area. We need the rain.

@mikelehne4886 Ай бұрын

Bummer - dropped my DX4C transmitter and now my boats get about 20 ft away and die! I have close to 15 receivers programmed into the transmitter. I found a used antenna and hoping that cures the problem. I have purchased a second transmitter but hoping the antenna does the trick. The waiting for deliveries is the toughest part.

@IRONCLADRC Ай бұрын

I hope the antenna helps, keep us updated

@jacobscourtes576 Ай бұрын

Locktight 603 is what tenshock uses

@IRONCLADRC Ай бұрын

Tenshocks connection let loose, I run several boats for years now with jbwelded connections and works 👍 great.

@HarborProps Ай бұрын

hey big b, huge fan. wanted to get your opinion on prop size. running a custom built 30" hydro on a 4074 1700kv on 6s. weights about 9 pounds. 180a seaking esc. Currently running the pro boat 1.7 x 1.6 prop. boat goes plenty fast but it takes a minute to plane. what size prop do you suggest to get up on plane quicker, even if it sacrifices some top speed. Thanks so much!

@Wanted1069 Ай бұрын

Braze it!

@IRONCLADRC Ай бұрын

I thought about it, but you gotta get it so hot it may weaken the stainless steel wire

@Wanted1069 Ай бұрын

@IRONCLADRC Not for solder. Don't heat it until it's glowing. Just pre heat for a few seconds. The solder will liquify pretty easily with flame. If you have any trashed drive dogs and a scrap piece of that diameter stainless shaft, try a test piece 1st. But I don't think you'd take the temper out of the stainless, so long as you don't go crazy with the torch. Just an idea. And it may save you from having to service it again.

@IRONCLADRC Ай бұрын

@Wanted1069 I have a drive dog that needs to be soldered on ill try the silver solder on that one thanks for the info

@Wanted1069 Ай бұрын

@@IRONCLADRC anytime!