That's great to hear! Thank you for watching and commenting mate, Cheers! 👊🇺🇸👍

Your very welcome! 👊🇺🇸✌️

Very welcome!!! another little tip...I put my steering on its separate ch that way i can trim the steering to run straight down the runway without effecting rudder...So with 8ch, you can still do the same in the MFC2085 as well...go to the ch the rubber is on an you will see something like aux-1 (rudder) aux-2 is the steering and you can trim it from the mfc...draw back is you will have to stop the jet to trim it on the mfc then go again and repeat...I found it easier from the TX (forgive me im at work and dont have it in front of me)

Thank you! Glad it helped you out. Hope you enjoy the f16!!!

My pleasure, glad it helped. Let me know of anything else you can think of (video wise) that I can make to help out. Not too kuch out there on these or the HSDJETS. Please sub and tell you pals about this channell. I really appreciate it. Thanks!

Hmmm if it was me....i run regular sbus to the mfc 2085 and run sbus 2 to your turbine. You'll get telemetry from the engine

Well, in that case. If a new never installed unit. Tou would go in there and tell it what surface for what aux you want to use. If from a crashed or pre programmed, you will ha e to go into each surface and see what aux goes to whay

If using the mfc. On tx 1 rudder

You don't have to disable the S Bus you'll have to remove the MFC off of the plane and you'll connect your receiver pwm into the input slits on the bottom portion of the MFC..look on page 07 of the mfc manual and page 10... page v10 lower left shows you the order channell 1 is "aux-1 on page 7...so aileron input goes on R-07, elevator R-08 and so forth

Also with futaba sbus compatible recievers.....some you have to switch the "mode" on the rx to have sbus enabled...on my r3008sb rx I have to switch I believe to mode 3 to have sbus

What reciever ya using? Is the RX away from other electronics, no nicked wires?

The J10 also has a Gyro to the surfaces just want to make sure the twitching isn't that

Yes

@@NoonzAirborneRC do you use this on a turbine jet? And are they reliable?

@@esskiahastings7974 yes i did...it came in a PNP turbine (HSDJETS super viper) i liked it so much i bought one to throw into and turbine i have.

I would bot use the AS#X from the receiver in the turbine...the RX WILL FAIL!!!! it even says on Horizons page when you look at the receiver "not for use in turbine" the rx is not shielded as it cant be since a receiver and the freq. from the noise of the turbine messes with it. if using a gyro use a stand alone like Bavarian demon or a spirit AERO like i did.

You could but for the super viper you wont have enought chanells

F-16?

@@octane2099 you could but you wont have brakes, i dont advise that

@@NoonzAirborneRC sorry to bother you so much just wanna see if is worth spending the 1,500 on the jet but on my freewing f-4 I have brakes I Yed it into flaps so half flaps is half flaps full flaps the brakes come on and I have and external 2S Lipo battery for it instead of taping into the bec would that work on the hsd f-16

@@octane2099 yeah i would not do that on these jets

The board is setup to send power thru the throttle I believe. Try connecting to the throttle ch. And see if it powers up if not go into system setting on the mfc2085 and select "power setting" then "reciever" and make sure it's not "off"

Im betting the power setting is set to off...reason it's not sending piwer to the 'R' ports

@@NoonzAirborneRC It is set to 6.0v. and is not powering the receiver. I have connected THR to R012 and R06 and no luck.

@@bobby456gt polarity correct? On your leads?

@@bobby456gt get a multimeter and touch black to neg res to middle pin on the R ports see if registering 6.0v...if not contact who you got it from and ask for a replacment