WMO to Base oil - recovery of the base oil.

No video

WMO to Base oil - recovery of the base oil.

Рет қаралды 9,227

Күн бұрын

A few steps to recover a base petroleum oil out of used automotive motor oil.
There are five main steps:
1: Collect and prepare WMO for distillation - filter with a centrifuge.
2: Distill WMO with an oil distillation plant.
3: Chemical treatment of the distilled waste oil.
4: Filter the treated oil with centrifuge, remove water and any free floating particles.
5: Settle the resulting oil with an absorbent.
Ethoxide oil distillate treatment: • Waste oil distillate f...
Build Your Own Waste Motor Oil Centrifuge!: • How To Build Waste Mot...
WMO pyrolisys retort: • WMO Pyrolysis retort pt2
Website: www.ferromit.c...
Contact: www.ferromit.c...
Contact ferromit@ferromit.com
#diesel #gasoline #petrol

Пікірлер: 64

@heyyoubuddy6749 8 ай бұрын

Hi Alek you have the whole process down Pat!!! That’s so awesome. Diesel here in Kaliforniastan is still $5.39 a gallon, and we don’t see going down much, due to political ideology. This method is much more involved than running black diesel but it looks to be much better quality. Thank you so much for sharing. God bless you and the family. Have a merry Christmas.

@santeryi9 8 ай бұрын

Thanks a lot for your comment, and yes it is a bit too complex, but it is a base oil recovery, the resulting fluid can be used for lubricants production if laced with proper additives, but as a diesel replacement the silica step can be avoided. Also it is not about the initial cost of the diesel fuel replacement. I am gaining some knowledge and experience in this field in case there is no fuel available at all at any price. God bless you too.

@elcaboelcabo2881 8 ай бұрын

I am using the last of my KOH. Good to see that NaOH and ethyoxide also works 😎

@santeryi9 8 ай бұрын

Sure it does.

@dasgehtsienichtsan 8 ай бұрын

Very good result 👍🏻 I always love your videos

@santeryi9 8 ай бұрын

Thanks a lot.

@tonydiesel3444 7 ай бұрын

Don't forget about the longer feed tube to the centrifuge one other option is a feed tube and an accelerator cone just a centered tube on the bowl that has three or four holes in it holes must be opposing from each other it eliminates the splashing splashing is UN centrifuge oil

@santeryi9 7 ай бұрын

Thanks a lot for your interest and for advice.

@donmfalme 7 ай бұрын

Hi Alex, I really appreciate the work you do. Can the diesel produced run in a common rail diesel car?

@fuootechoilpurifier Ай бұрын

we have the oil distillation plant to convert waste oils to clean diesel oil which can be used in the cars, trucks, machinery, etc.

@Archebe 2 ай бұрын

Hello friend, I bought you a manual for a reactor a year ago, I tell you that it worked for me, but I am seeing that you are adding a catalyst, I would appreciate if you could tell me which one it is, best regards

@santeryi9 2 ай бұрын

Hi, if you are interested in further cleaning of a distilled oil, then you can either clean it with a mix of sodium hydroxide and methyl alcohol, or settle it over a silica gel.

@gabrielene2543 8 ай бұрын

Hy Alek.Here is Romania ,east Europe.We can use this product for common rail diesel engine without silica gel step?Thanks.

@santeryi9 8 ай бұрын

Yes, you can, though let it settle for a few days and filter before use.

@user-wu1xd8fl4v 8 ай бұрын

Александр.классное видео!

@santeryi9 8 ай бұрын

Я старался, спасибо за комментарий.

@andreels6560 8 ай бұрын

Alek you can clean your oil and diesel in a couple of minutes using fullers earth

@santeryi9 8 ай бұрын

Did you tried it yourself?

@andreels6560 8 ай бұрын

@@santeryi9 do you use WhatsApp? Can send you plenty of information and photos

@andreels6560 8 ай бұрын

@@santeryi9 yes can give you plenty information if you have WhatsApp

@tungvu929 7 ай бұрын

Nếu nấu 1000 lít dầu nhớt thải thì tốn bao nhiêu kw điện thế anh.

@santeryi9 7 ай бұрын

nó sẽ mất 300kw điện.

@tungvu929 7 ай бұрын

Làm cách này còn mùi khét không anh

@santeryi9 7 ай бұрын

Xin chào, phương pháp này là để thu hồi dầu gốc, loại bỏ mọi mùi hôi, thu được dầu gốc không có mùi.

@sylvanenergy 8 ай бұрын

Hello, my friend, I was wondering if using reagent grade sodium hydroxide made any difference at all?

@santeryi9 8 ай бұрын

Hello, my friend, the reagent grade has no neutral filler addred (This one contains only 500g of hydroxide per kg of product) so it contains about 50% of lime or chalk, so the final result is haisy, cloudy and require centrifuge. The reagent grade will do transparent oil with no floating particles.

@kelechikingsley5899 6 ай бұрын

The end product is base oil and not diesel, right?

@santeryi9 6 ай бұрын

Yes, it is base oil, thogh diesel engine was called an oil engine first and fuel was - light oil, so in fact there almost no difference between base oil and diesel fuel.

@antoniosestar3671 8 ай бұрын

What additives can be used to make the oil more thick? Also where to get those additives? Would store bought additives for cars work? Like Liqui moly

@santeryi9 8 ай бұрын

You need to do your homework. Everything depends on the type of lubricant planned for production. In most cases, the additives include metal oxides, lithium, calcium, sodium, molybdenum, along with foam suppressors and solvents. To create a lubricant, one must obtain a production standard document outlining all the additives, their required proportions, as well as specifications for final viscosity, flash point, freeze point, and lubricating properties, including the relevant test methods. Therefore, your lubricant must align with a specific standard.

@danielmanchi9084 6 ай бұрын

I appreciate your work man. I would like to know the temperature you heated it up to or what’s the best temperature to use in distillation of waste motor oil for both diesel and base oil. Thank you. And can you use earth clay after the silica gel or it’s not needed? Can this oil run on diesel cars without any problems?

@santeryi9 6 ай бұрын

The best temperature for oil distillation is 410c , for final drying 60c and if treated correctly can be used in any diesel vehicle.

@danielmanchi9084 6 ай бұрын

@@santeryi9 thank you very much, I appreciate but how do I treat it correctly after distillation? Any chemicals that needs to be added after distillation? Will I have to hear it to 60c again? And what do you mean by final drying please?

@user-ju5uf1wo4g 7 ай бұрын

saya dari indonesia .butuh ilmu untuk bahan kimia.oil bekas bisa seperti baru lagi.kamu cerdas alex.berapa jenis bahan kimia yang harus di campur kan biar hasil nya bisa ok.❤❤❤😅😅😅

@santeryi9 7 ай бұрын

Ya, Anda dapat menggunakan kembali oli lama, meskipun sifat-sifatnya juga akan hilang seiring berjalannya waktu, jadi lebih baik untuk memulihkan oli dasar, lalu mencampurkannya dengan semua aditif lagi, ada beberapa metode restorasi oli langsung, dan saya masih bereksperimen dengan mereka, setelah saya mendapatkan hasil yang bagus, saya akan menunjukkan caranya di sini.

@jasasumurborjogja 5 ай бұрын

Saya ada fuller earth

@jasasumurborjogja 5 ай бұрын

Asam sulfat fuller earth

@ZarawarKhan-gs8hr 8 ай бұрын

What if we use methyl alcohol instead of ethyl I read somewhere on the internet that methyl alcohol reacts with sodium hydroxide and produces yellow colour.The following oil will look yellow in colour

@santeryi9 8 ай бұрын

Yes, it should work as well.

@ZarawarKhan-gs8hr 8 ай бұрын

@@santeryi9 brother humble request please do a video with it as it's cheap(methanol).

@thelistener7033 7 ай бұрын

hello, thank you for your awesome job. I'm from France, i live in an old truck from the 80's (Saviem SG2) and i love diy stuff (also because i'm poor lol). When i have time (and money), i will buy your wmo continuous distillation plan. However i have a question : With my old truck i run directly with wmo, just filtered at 5 microns, with a 30 plates exchanger with the cooling liquid of the engine to warm up the oil. Works good with a "little" black smoke. But i wonder, can i remove the odors a little by some sort of process, without centrifuge and distillation ? Will your ethoxide cleaning method works a little on just filtered wmo ? I really don"t need a clean transparent fuel, but if i can be less odorant it could be great. Again, thank you, i love your videos! Happy new year!

@thelistener7033 7 ай бұрын

in your opinion, what makes the most "negative" odor when running on wmo ? sulfur ? and what the methylated spirit is for ? thank you

@santeryi9 7 ай бұрын

any used unprocessed oil has a lot of additives in it, and those additives make oil stable, also stable to any sort of deodorizing and cleaning. so the ethoxide method will not clean a straight engine oil. There are some other methods that are designed to remove free carbon sediments from used oil, but they also include centrifuge, and alkali solutions.

@thelistener7033 7 ай бұрын

@@santeryi9 okay thx for your answer. So with a centrifuge, and alkali solutions (by alkali solutions you mean sulfuric acid etc ?) i can make my dirty oil cleaner ? maybe i'll try to make a centrifuge one day !

@banglababumoshai9932 8 ай бұрын

How much will this whole setup cost?

@santeryi9 7 ай бұрын

honestly do not know, built some parts for myself without intention to sell.

@user-be4vy8ik6h 5 ай бұрын

What do you think about using sulphuric acid and then doing the NaOH part. And at the end bleaching it with bleaching earth or activated carbon ?

@santeryi9 5 ай бұрын

I personaly do not like to deal with sulfuric acid, the byproducts are pain in the ... you know, you can try it yourself and yes it will work.

@user-be4vy8ik6h 5 ай бұрын

@@santeryi9 i tried, with various ways, but my end product is not that good,i need exact process, watching on KZfaq and trying without proper knowledge is not helpful, can you help ne

@santeryi9 5 ай бұрын

@@user-be4vy8ik6hThere is a contact details in the description, you can contact me. Do not have much time though. And may chargoe for consultation.

@ZarawarKhan-gs8hr 5 ай бұрын

Can we clean the residual fuel oil (furnace oil 97percent + gasoline 3 percent) since furnace oil is also produced after distillation only needed thing is ethoxide cleaning can u guide me brother

@santeryi9 5 ай бұрын

you can settle it for a few days with silica gel, about 5% - 10% by volume.

@ZarawarKhan-gs8hr 5 ай бұрын

@@santeryi9 thanks for replying mate but I guess dark colored black so I think ethoxide cleaning is must with silica gel it failed