Thank you for that helpful info. I'm also ready to install a woodstove and my question is it better to install woodstove pipe straight to the wall vs up the stove then 90degree turn toward the wall. Concern about the effectiveness of the draft

very informative video. I've been toying with the idea of building a wood stove for my garag/shop. I'm glad I watched this video.

thanks for uploading this

I love your videos! You always explain everthing in detail, that is much appreciated! I have a question, I am lookinng to install an All nighter wood stove, with the 6 inch rear flue, do I have to buiild a wall ''hearth'', or just a floor hearth? The stove says it needs to be away 36 inches from any combustables, but I can't have the stove sticking out into the middle of the room, what materials would you suggest that I use for the wall behind the stove? Thank you very much!

When going thru vinyl siding there is a vinyl block out for the application. Allows connection to substrate rather than over the vinyl. Over the vinyl creates compression of the vinyl and never water seals.

Thanks for 3/4 of how to install a stovepipe.

Cool Man! Thanks for the comment. You may be able to find a Wood Stove used for a few hundred bucks and save a lot of work and money! Unless you have the time and some materials lying around to build it. Then I would have to say go for it!

Thank you for posting. Really good video.

Hey @mrEnergy511 do you have a video for how to seal a gas furnace side exhaust that goes through masonry foundation in the basement?

What you will want to do is build a "Heat Sheild Wall". To do this you will need to have an air space between your Cumbustable wall and your Heat Sheild Wall. Start with Metal Studs by screwing them to the Cumbustable wall Verticaly with the flat side out. You will need some long screws! Next just install cement board over the studs alowing for air flow 1" top and bottom with studs vertical. This will give you 1 1/2" of air flow space between the two walls. I need to make a video on Heat sheild!

Most of you guys who post negative comments are funny (in a stupid way of course).It is his house and he did it the way he came up with. I would like to see some of your unprofessional homeowners work. If he could have afford a professional he would have got one but you know it alls get me.

Do you have an image of the thimble being placed? You cut that out of the video. I am wondering if you just dropped it in through the siding/wrap/wall with no flashing whatsoever. That is a huge water leak waiting to happen.

lookin good!

If you have a porch roof on the front of your house, can you vent it out that way or does it need to be ran all the way up to the main roof? Using 2 45% angles I can get 10 foot out from the main house going up through the porch roof.

the hole that goes through the wall does it have to be bigger or would the pipe fit snug in hole. We got the dural vent triple through the wall kit and on the inside black stove pipe

I have the duraplus brand. Where the horizontal T portion meets the vertical, it leaks along the factory seam. Is this common? Should I silicone that? I wouldn't be to concerned but it weeps and follows the pipe into the cabin and leaks a little. Note-the exterior thimble was sealed with high temp silicone around the pipe and regular silicon where thimble meets exterior wall (T-111).

Great stufff***********

What is your opinion of the Duraplus triple wall system they sell at Home Depot? Any good for a Morso 6148 wood stove.

I want to install the same type of wood stove but in my basement. Rather than shoot up through two floors and a roof...I am thinking about shooting to outside through the basement wall then straight up the side of the house. As in this video, I will run into the roof eve. Can I elbow around it? As long as I use good bracing?

Wondering where you purchase your Metal-Fab parts from. I am installing an Elmira stove that has 7 inch chimney top port. I have a 7 inch ID metal fab type A T and a few pieces of type A pipe. Looking for the wall thimble , short wall pipe, and a few long pipes for outside. I seen some on Amazon and went to the metal-fab website. Very confusing... Also looking for the wall mount triangle support and wall supports... any help would be appreciated... Thanks Matthew...

HI, I have the exact same installation and i get cold air coming in and some water drops. I suspect ice and/or condensation is forming between the dual walls of the outside chimney. Is it possible? Will scealling the joints of the chimney with caulking do the job? Thanks for relying. Cheers!

Yes you can! A pair of elbows will cost you about $200. A roof flashing will cost $30 or $40.

Good video. I know local fire codes are different but i was told that i couldn’t have a wood stove with a horizontal pipe more than 6”. 😢

Anyone know what the clearance is from ground to bottom of support box? I want to install thru a block garage wall toward rear of garage. But hv ground slope toward back. Not sure if hv to dig for more ground clearance and regrade. Thanks

where did you buy the parts from?

Damn, where he punched the T to get it into the flange there is a big dent now.

Ok so I’m interested in what happens between about 4:27 and 4:30 with the interior of the wall and where the thimble goes. I’m curious if you just have the insulated pipe running directly through the wall or was there other preparation done other than ensuring the space between the pipe and the wall itself. Thank you for your video.

Good stuff! That will work

Thanks for the good info. I have a question regarding the max elbows you can use with a pipe, also can i run some of the pipe in 45 degrees angle? Thanks.

I bought super event for Menards in Minnesota and the adjustable shelf support triangular thing says it has to be the other way around at the bottom. Is that true?

I wonder smthg about the support.How can ıt carry the vertical load on it. what about the thickness of the support plate ?

I have a question. My stove goes through the wall like this. When I had my pipe level in the house going straight out of my house I was having creosote issues fast. I re plumbed the pipe to run up hill out of the house and it burns way more efficient and I not have build up so fast. Just wondering your thoughts on this?. Thanks in advance for your time.

I assume you don't get much snow. We get snow 4 foot deep on the roof, then the snow compacts and freezes into a block and when it slides down the roof it will take that chimney out like a matchstick.

Have pellet stove first time but kit pipe is a little bigger than stove hole how to fix it 3" pipe

How the heck did you end up installing the wall support gussets upside down? They should be below the cleanout, so your lag screws are not penetrating the firestop. That being said, your video was instructional and entertaining at the same time - got a ton of views. Thanks.

I am getting ready to do this install and its almost Identical. I have a couple questions im hoping you can help me with.. 1. when installing the chimney bracket that holds the weight of the chimney,, is there something that would match the siding notches or do I just calk the crap out of the big gaps between the siding and the bracket.? 2. I also see people asking if you installed this support bracket upside down. Just asking for clarification. I want to do it once and be done.. 3. at the soffit area. from underneath,, is there a piece to hide the ugliness of cutting into the soffit or is that just left open to flap in the wind? I think I got the rest,,, I hope.

Is that electric wire in your wall where the hole is cut for the pipe?

nice.

Y no install video on the interior side?

estimated cost of supplies? besides the wood stove. also, how much was the wood stove? lol. what would you charge for labor? i want to have that done , oil is too expensive!

How much would a install like this cost?

Can the wood burning stove be connected directly to the house chimney? And if so, does the house chimney need to be lined? Thanks for posting.

Thanks for watching my video and for your kind words! I install Wood Stoves and Fireplaces every day.

Can you please give a rough estimate of the cost for the piping etc?

If I do the same thing with a wood cook stove, could the insulation catch fire from the heat of the pipe?

Is there a minimum recommended length of the vertical pipe coming out of the top of the stove? Will it draw ok if it's shorter? I have a 24" piece with an elbow mocked up to my new stove, and I like the way it looks. Do I need to make it longer, or no?

When i bought my house, It had a chimney removed on the edge of house with an open hole in the roof like this install. I bought my house as-is and had to do the repairs myself. When i did the repairs, i thought to myself.. These metal stacks are not very pretty anyways. Why not extend another foot or so from the side of the house and save cutting holes in the roof. Can mrEnergy or someone comment to my question? -thanks

According to UK Building Regs this installation wouldn't comply as any horizontal length of flue has to be no longer than the internal diameter of the flue ie/ 6 inches. So if you happen to be looking at this in Great Britain your flue pipe exits through the wall at 45 degrees into a 135 degree tee piece on the outside of the wall.Also the heatproof area of wall behind the wall varies according to the type of stove but usually requires 70mm of non combustible material.

Hi Matt, I'm getting ready to install a Metalbestos 8T-Twk Thru-Wall Support Kit (TWK) and the instructions for my kit shows the wall support bracket with the triangles pointing down "like a shelf bracket would" in your video you have the triangle pointing up, is that because you are using a different kit?

It seems to me it would have been better to installation to go through the ceiling to create the most positive draw. My intent is not to criticize just asking anyone out there if that observation has any merit. I am considering a wood burner in my 1365 square foot manufactured home. Just asking for advice. Also, would it be a good plan to centralize the wood burner in the house, or not? Thanks.

Was that double wall pipe? Or triple

Where can I buy these pieces at can you send a link

Right off the top i gave up? Truss?

how much did it cost ?

how much does it cost to have an install like that made?

20 years installing wood stoves and fireplaces! I'm sorry to let you know you were misinformed. You look like an artist and I am a contractor who is lisensed to install Class 'A' chimney pipe. Why do you think they GALVANIZE chain link fence. To hold up to the weather! I think you should stick to what you know like playing that ther gitar! Next time you get FREE advice ask more than one person! I have layed a lot of pipe my friend and I'm sure you have done a lot of stroking of your instrument!

You might want to add some sort of heat shield on the walls behinde the stove ????

just the wall studs for the weight. wow.

Should work

how do I contact you for a job in Lehi?

why go through the eve? could you not come out far enough away from the house to avoid that?

How large are the tiles you used for the hearth?

You must have proper clearance from your pipe to a combustable wall. 12 to 18 inches for single wall black stove pipe. 6" for dbl wall

I installed the same stove in my house and I have creosote dripping every where. any ideas?

What is the name of this flashing? I can't find it on home depot or anywhere.. thats exactly what I need though

Easier if you start with the stove, work your way up & find where your center is. You can move the stove slightly to get it between the studs as you said

That wall is going to leak rain like a sieve.

It would of been nice to see you hook up the inside pipe.

If your installing a Chimney Pipe through a Brick Wall you will do the same thing only use a grinder with a diamond blade. You could also use a circular saw with a diamond blade or an abbrasive blade. Brick is non-conbustable so there are no clearence issues. Are you planing to pipe into an existing Chimney? Or is it just a brick wall?

My question why is there no shield on that cutting device looking for your neck to be sliced very dangerous thing to leave out.

Them would be called studs there bro

from the ridge of the house..... chimney should be 3 feet above.......draw a horizontal line from the ridge and top of chimney should be 3 feet above that point....maybe it's diff today but that's how it used to be

Is an electrical line ok in the thimble cavity?

I believe you are incorrect - sounds like you stated you 'could' use elbows on the exterior. As fingers967 stated - the install manual states it is not approved for exterior applications. Since the building inspector/fire inspection relies in part on the install guide of the product you used and NFPA211 - it would simply not pass inspection. I'm not saying I wouldnt do it...but it is technically against the manufacturer install manual and therefore not acceptable during a diligent inspection.

nice triple wall with a dent right in front.

It looks like the interior flue pipe is upside down (female flange on top)

why wouldn't you go straight up instead of the two ninety bends ?

is it a 2 story building?

I Am doing a 8 inch stove pipe

elbow around the eve... $200 for a pair of elbows is a good amount of money to spend if you don't need to!

How did this guy get so lucky and not hit a rafter when he came up through the roof?

That electrical wire will melt, that wire should be re-routed

looks pretty close to the wall inside to me on the back corners, and the wall support bracket is put in upside down. also very lazy not to move electric wire in wall, and not cut more around where it touches house by roof . could cause fire in those spots

NO WAY! 7" is old school!!! most all EPA wood stoves are 6" and thats is the way to go. 20 years of installing and when I started 7" was going out. 2013 bro get rid of your mullet! 6" is all you need for a wood stove with a 6 inch collar...

Yea I would not have cut though the overhang they have a offset for that.

Two feet to go???at bottom of eaves....suppose to be three feet above the ridge on a level plane to avoid down draft....

Yeah...but didn't that fellow write that the "top port" of his stove is seven inch? I don't downsize a chimney unless the stove mfr. says it's OK. (and I wouldn't do it then anyway).

It’s 2 inches to combustibles. I’m WETT certified.

That wire is way to close to your heat source!

Nice stocve but not esrhetic like chemine finish brick

why would you compromise your roof when you are already outside the house? that's the worst idea I can possibly think of!

umm just one thing he has done wrong you can NOT use a horizontal peace of pipe coming out of the rear any more than 6 inch because of the gases he has 12-14 inch peace it will cause carbon monoxide its bad .

Sorry dude you are wrong! Galvanized metal is for outdoor use!!! 2100 degree class 'A' chimney pipe is made to be exposed to the elements.

You'd do best to stay with the smoke outlet size of 7" , or upsize it to 8". There isn't much 7" chimney around anymore..but I installed a good bit of it back in the '80's and early '90's. It may be tempting to downsize it to 6" for cost and availablity, but doing so is a No-No unless your stove installation instructions allow it. If you're still not sure of your project get some help. It ain't brain surgery but there IS a learning curve.

This guy is going to burn this house DOWN! He has chimney touching a combustibles!!! You need a wall thimble for your pass through. This hearth doesnt meet code! Your clearance to combustibles are way off. The #'s he states are even wrong. You need those bands every 8ft not 10, clearance is 2in, not one.

That is a "hack job" and it looks like crap.

You did a good job but its PATHETIC that you have to cut the roof rather that go around....I am installing one soon and I have a 12" overhang.....

Left a lot of material out of this video.

Stop beating the dog.

Why did you not even cover the roof flashing install?! Incomplete video.