IMPORTANT! 1:00 This is not special tool! This is simple valve stem cap, usually founded on bicycles. If you don't have this type of cap, use small needle nose pliers, or cut slot in nail or something similar. Thank You!

Very good video, but people should be aware that motor oil will harm the tyre valve. The tyre valve is a mix of rubber and neoprene which can be harmed over time by oil. Would strongly recommend the use of soapy water which is just as effective & dries out giving a seal that will last without any harmful effects.

Great video. Loved the nail /cap hack

Never use oil! Dish soap.

The wheel looks like it has seen better days !

Top video, many thanks from me in Edinburgh, job done. My purchases - valve stems and a Silverline make 4 way tyre valve repair tool to loosen/tighten the tyre valve and to attach to the new valve stem to pull it into place: Total cost £3. I already had a cheap tyre inflation compressor that runs from the 12v socket in the car. Issues - all went well until I tried to rebead the tyre but couldn't get air in fast enough to reseat it. Solution - raised up the side of the tyre opposite the valve 6 inches so that the wheel was clear of the ground. Then started the compressor and stood on the wheel on the unbeaded section and bounced gently up and down pushing the wheel downwards into place. As I did this the tyre quickly started to take air and popped into place. P.S. For those considering using the alternative replacement method using the tool that punches a new valve in without having to unbead the tyre. It will work if you have steel wheels but i'm not if you have alloys due to the access hole for the valve being recessed.

Thanks, you just saved me from buying that little 4 way tool that is used in so many other videos on this topic. Great video.

Oil attacks rubber. Use soapy water. This is probably why the first valve stem was leaking.

What is that heavenly hypnotic music?? It’s got me standing up and shimmying my hips back and forth like I am one with the beat! " MARTHA come here! " something’s happening!!!!!

I liked that you checked your work for leaks before just putting the tire on, getting on the Autobahn with the car top down and a few girls finding out the HARD way.

Your the best!!! I always get help from KZfaq, but did not think there was something for this. Thank you!

Never use oil, it damage the rubbers.Use soap instead of oil.

I just subscribed Bro’. This is really good info and the tune is pretty cool too.

Thanks. Perfect just what I was looking for.

Absolutely perfect video. Could use a bit of text but other then that it's perfect

A side note, since there's no actual sound there... A hissing sound and quite strange smell (to some) will be present when you remove the valve core. Another is, a popping sound of the tire when it seats right to the rim (sometimes very loud) which might surprise some peopl who knows nothing about what they're doing 😁. Good info here. Keep it up eh

Thank you. Didn't know it was that simple.

Petroleum products eat rubber. Using soap on the new valve stem won't damage it. LOTS of soap.

The video I was looking for. Thanks man.

Amazing thanks for the video :)

Great video, very clear. Not a fan of the music, muted it.

That's a real Rube Goldberg bead breaker!

Great tip thanks!

Talk about improvising, Nice

My man, the nail is genius

Thanks! That helped!

Thank you was veary helpful!

Este vídeo si que sabe el como no dañar la válvula y usar el saca pivote felicidades

Awesome video dude!!! Get tool kit at Walmart Canada Okanagan. Oddly they don’t have valve stems, one of the boys in automotive department gave me one thanx to all...

Thanx 👍👍👍

Don't use motor oil, it will break down the rubber. Use dish soap, or soapy water, or even just water.

Wow this is a awesome tutorial !!!!❤️ Blessings and more blessings to you and your family in Jesus name Amen

Helpful video but the music BLOWS!

Silicone grease in lieu of motor oil

Great job! Thanks for the video! but would the oil eat the rubber? Maybe better to use soapy water like dishwashing liquid.

Like the music u used in this video now I never go to the garage again

Ok. Now you can clean 🧽 the damn rim with soap 🧼 and water 💧.

Best film of the genre

Bonne vidéo !!!!!!

Can I do this when my tires have a TPMS ? I wouldn’t wanna damage the sensor if I do this. One of my tires keeps loosing air. Thanks

Oil and rubber don't mix well

The best rustproof oil is Ballistol

Great vid, can't you push the stem out instead of cutting it? You push the new one in could it work the opposite way for removal?

Ended up using some good old spit and my hardwood nail extracting thumb...😂

Good IF you don't have the right tools. With a valve change tool kit (less than 20.00 USD) you can do this without removing the tire and in less than 2 minutes. Oddly, very hard to buy a good one in the US or Canada. I ordered my from the UK through Ebay.

I've used the base on a bumper jack to break tires down before. Now days bumper jacks and vehicles you can raise with one are getting hard to find.

Oil on rubber is an absolute no no rite off the bat, silicone spraywould be more appropriate thing, of dishsoap..

time for some new rims

The tire store seems to use soapy water to seat the bead. Hard tire users can spin a tire on the bead, or peel a bead that otherwise would have held if you leave oil on it. Great video, thanks. I’m going to use your pliers trick but substituting soapy water for oil.

Oh ok. Let me try this again.

Should of pulled stem with vice grip pliers.

Problem is you need a compressor that's capable of moving a lot of air faster then your normal air pump in order to seat the tire back to the rim.... Which most people don't have either

I had great difficulty inflating . really hard to push the tyre beading over the vaulve area, Luckly I had tyre leavers.

Nods head to beat😎

Whats the tool at 3:00 that you used to pull the stem?

I appreciate your time and effort, but 7 just convinced me thar it is worth paying $5 for the tire technician to fix this for me

That thing you're screwing is actually a special tool

Are those bubbles coming from that newly installed valve stem?

Sometimes the simplest things escape my mind. Like putting a little boat through the cap🤦

I wrestled my tire over the rim with 2 big screw drivers and alot of curse words, would not recommend lmao

what is the part you used to pull the valve stem?

Jais jamais réussi même en regardant la vidéo

Now, show us how to install stem without separating the tire from wheel?

Just the kind of video I like: Not a bunch of talking, just showing what to do with a little chill background music. Thanks man.

When assemble tire by fire flash, is better assemble stem afterward because otherwise vacuum pull tire off, if it is in place. Wire for pull it in hole works.

Ya that would be a tool

dope ass music

Can you just remove the gold tip?

Helpful video but the music was annoying

USE AN ELECTRIC SCREWDRIVER WITH NO ATTACHMENT, HIGH SETTING, HOLD THE STEM AND VOILÀ!

I think the hardest part is removing the rim from the tire.

Song?

Oil on rubber are you mad? Valve and tyre? Soap, washing liquid, etc !!!!

I used a a bike pump and pulled and some Vaseline

That is definitely a special tool

never put motor oil on rubber

i kno a guy who ca push them in from the front by hand

Are you supposed to use GM oil on that BMW rim? WARRANTY VOID

What’s the size

that oil you put on there gets inside the rubber, in the winter the salt will force it out and you will have a cracked valve stem again, save that other one from the pack lol

Top Tip! don´t use that brick and vise on your Lamborghini rims!

OIL CAN RUIN THE RUBBER VALVE STEM ITS BETTER TO USE A SOAPY WATER TO LUBE THE RUBBER VALVE STEM

Motor oil will destroy that valve stem in a year, use soapy water

Maybe different music would be better

Yeah no special tool! Only simple press tool! LOL

Says you don’t need special tools but proceeds to pull out special tools 😂

“Without special tools” - uses valve stem removal tool. Most people would consider that a special tool and wouldn’t have it around.

Wash the damn rim.

At 3:54 in your video

Music weird

This definitely doesn't work with a plastic valve stem. I tried it in a pull the nail right out

No special tools huh? Ugh what about the tool you used to break the bead? I don't even know what that was that you used. Therefore, to me it looks like a special tool. Especially considering i don't know the name or how to even use it properly.

Motor oil eats rubber bruh 😂

Nice video on the how to. Crappy music though. Would much rather listen to Truman Capote narrate how to do this job than listen to that atrocious "music".

Didn’t work. Tore the stem in half.

Just pony up a few bucks and buy the cheap kit from Amazon . (AME 51025) Quick Valve Change Kit And stop the madness 😠