a bank card also works

Sucks, best controller i've ever felt. Gonna return mine tomorrow and hope i get a good one

thank you so much. i was skeptical and thought that i would definitely notice the paper but i actually don't... hope it lasts for long enough to not become pain in the ass to change too often

@ioelssnnalalnxxnxjsoskznxj9277 Good stuff you're welcome! I'm not having any issues to date

Bro i wanna fix mine clicking

Ma bucur! Ce probleme ai avut cu el?

@@dreptuteodor toate butoanele și un trigger sticky....

@@florintanase9348 vezi ca la trigger sticky mai poate sa fie o problema. Ele au un mic pad de spuma care este pt protecția triggerukui ca să nu se izbească cu putere de carcasa după ce este apăsat. Mie mi s a întâmplat sa se dezlipească ala și sa fie sticky și cu un zgomot ciudat. L-am pus la loc și l-am relipit, este un pătrățel cam de 2mm pătrați.

@@dreptuteodor eu am dat o tona de electronic cleaner pe zona unde ar fi acel pataratel si acu merge bine; mai este un pic sticky dar nu ma mai deranjeaza...orcum multumesc pentru informatie

Same now they are unresponsive

Same happened to me

So theres two little magnets that hold the triggers to the case of the controller on the back half under all the hardware one of them fell out guarantee it. Same thing happened to me when i was fixin it

These are supposed to have a face plate as he kind of shows. Theres glue where the grip ends behind the face on the left side above the grip and in between the d pad and left analog stick. There is more glue under/ around the a button. Take something like a heavy gauge guitar pick so that it can bend but not break. Right above the audio inputs there's the little slit that runs across to both handles. This is where you insert whatever you use and try to jimmy it very careful until you get slight clicks both sides. After that removal is easy but you have to pull very careful because the glue, it's essentially double sided tape but it's not and itll stay sticky if you keep it clean and even maybe swipe it with a damp cloth that has rubbing alcohol. Obviously never put anything near wet near the inside. Use q tips dipped in alcohol and dried lightly so that it's almost dry to touch the q tip. Rubbing alcohol dries quickly so it shouldn't be a problem if you're using a really light amount. It's going to get rid if any gunk sticky or dirty material that gets tracked through the sticks dpad triggers bumpers and the paddles. Recommend buying a electronic tool kit because it has torx screws that are quite small. After that you're on you're own .

T.H.C Mcgee what types of screw is that

@@9ifferent t9 for control case and t6 for the board screws

Frederick ok thx

same idk how to fix it and im scared to try it

Use Deoxit spray where the lb and rb buttons click the little buttons under the faceplate. Remove that little plastic resistance piece over each one as well.

This will fix only the sticking A button, not the unresponsive one. For the unresponsive you need to put something on the button. Mine works perfectly now...

Dreptu Teodor The title of this video says ‘Fix unresponsive A / Y button?’ What do you mean put something on the button? Can you explain more please?

Dreptu Teodor hello?

07:40 might want to watch the video.

@@tomojobs bruh did you even watch the video 🤦

Went through 4 or 5 returns - it's a manufacturing problem 100%. I gave up on it and just use a regular controller. Got tired of all the noobs who don't even realise their controller is shitty telling me it's my fault.

I had a faulty controller that was wobbly in the middle of the joystick making huge dead zone. Bought another one 3 weeks ago. So far everything is perfect. Never return for replacement. Always return for full refund. And then buy a new one. If you get a replacement it will be mostly a refurbished

i have 8th elite 2 controller and every has this problem

I'm on my 12 swap out. EVERY CONTROLLER can have a number of defects. ALL of them have face button issues (a,b,x,y)

I tried the method and it has work, you only need to take the face case and introduce the tape between the space of the button and the controller skeleton

I have the same problem but with the LB. It doesnt register only when I press it in very hard.

Same wtf is wrong with our controllers they cost way to much money to be acting up like this

@@ziohtleft737 Well If you think about how many mechanical parts in Controllers are and what forces they have to withstand you can understand why some break but for example at the moment I cant use mine and play with a normal Xbox Controller that doesnt break, kind of annoying Sry if I spelled anything wrong, not the best in english

Mine does the same thing

Between the actual plastic button (RB) and the circuit button it's a little foil of thin plastic, like those from folders. You can try to open the faceplate and look, you can see clearly the mechanism. Don't worry about the warranty, the warranty sticker is put on the inside screw, you don't need to open that, only the front cover and do it with a plastic knife or something similar for no scratches.

Rubbing alcohol will not help at all the Y problem, only the A sticking button because near the A button is a lot o adhesive in excess. The only problem with Y is that is unresponsive and rubbing / isopropyl alcohol will not help at all. You need to make the button a little thick in order to be perfect.

Yes. There is a small foam square that is about 1mm. Sometimes the glue dowsnt work and need to do it again. I made this procedure about 5 times on mine, next time I will use SuperGlue.

@@dreptuteodor thanks for the reply! Do you have a video on that?

@@jaewon679 I don't have but I can make it Sunday. Do you feel something soft when pressing the trigger, yes? Something that is not right but the trigger works electronically perfect

@@dreptuteodor the trigger works fine and feels pretty much the same as the other one but every now and again it feels like the thing that's rattling around somehow stops the RT from being able to be pressed, so i give it a shake to "dislodge" whatever it is then it works fine again. I need to crack it open and take a look but I've never done that before

It's very very easy, you just unscrew it counter-clockwise. Put any cap and just unscrew it.

Hazim Sharif same

try now. I tried to add the subtitles.

@@dreptuteodor says subtitles are not available

No u have to solder it

Use a hair dryer and when it gets hot you can screw off

it didn't work

@@kogmawdotwav Thank you for the feedback 👍

Hi. Very thin

put a tape and button got better, but still buttons dont work properly like in pro controller if you press button softly and move it towards hole edges you'll see button deregistrering at times if i put one more tape layout the gap is too small and button move up-down badly

@@muS5s You need to place a thing under the button, I mean between the button and the rubber. It's because of that

take the faceplate off and take the plastic off around the tactile switch and see if that helps, if not, take off the bumpers so you can get access to the tact switch button, put a good amount of alcahol on the switch and white button then with a small flathead screwdriver press down the tac switch button very fast and push down hard on it for a couple mins clicking it allot, then wait about 5 mins, and blow on it very hard a few times then wait about 30-40 mins to completley dry, put it back together but leave the plastic off the tact switch. This is what fixed my right bumper, when you first use it though it still might play up but keep pressing the button and give it some time and hopefully that will fix it.

@@GeXExtremist ill let you know how it goes =) thanks bruv

@@tutini496 it seems like a lot of bumpers going out around this time. Seeing a lot of new comments relating to this. My left bumper doesnt click and doesnt register at all if its softly pressed.

my RB and LB just a week ago is going through this problem yea seems like this is going around with a lot of series 2 controllers

@@tickergames3079 just do what i said in the comment above, my rb didnt work at all unless i pressed really hard now it works like new and my lb double clicked and now it also works like new.

I had the same problem, it looked pretty tight inside so I doubt it anything with the rubber underneath the buttons, but the sides. So After I tried to open it and realized that it is almost impossible without breaking it i took a toothpick and pushed inside and went all around couple oftimes and that did it for me

Same problem, I just tore it apart and threw all original buttons away and replaced with some other Xbox ones and it's been awesome since 😀

Try a little harder with downforce. Counterclockwise.

@@dreptuteodor yea I tried. Even used a wrench lol. I've got another one that I can't get that off of either. I tried heat also. I ended up just pulling the whole joystick essembly apart and unscrewed it after. It's wierd all the videos I see peiple just gently untwisting them.

Same

is it hard to press to the point it wont work?

when?

its a 9 min video, just watch it -.-

From the video it seems that they screw onto the 3D analog stick component. So maybe try twisting the entire joystick to tighten it. If twisting doesn't work, it could be a faulty soldering job but that doesn't seem likely because you would probably encounter some connectivity issues. I do not own a series 2 elite but I own a series one elite and have replace one of my thumb-sticks.

@@austinhendley9111 mine has the same issue on both sticks, even worse on the right stick, even with the caps screwed off the actual joystick they still have a slight wobble to them, no idea how to fix other than replacing the whole joystick unit

@@GeXExtremist thats how mine is i took the faceplate off and unscrewed both joysticka and it still wobbles like crazy. I hate/love this crappy controller. Microsoft hasnt even responded to my warranty claim on it

I think all are like this.

That is correct, I upened the gamepad many times and decided to use only the four ones for testing.

Hey man I broke apart my controller and fixed my trigger but now my Rb is broken. Any idea what the issue is I’m currently breaking it back down

Dreptu Teodor The Rb was working fine before I broke apart