Yaesu FTDX-10 tx audio settings basic

Рет қаралды 12,348

Jay N4GO

2 жыл бұрын

Пікірлер: 23

@rays9033 2 жыл бұрын

Great info for a new DX-10 owner, thanks!

@JayN4GO 2 жыл бұрын

Thanks Ray

@joseneves2822 2 жыл бұрын

Good morning, very cool this video 👍 Bought my radio in September and I'm still choosing the best setup

@JayN4GO 2 жыл бұрын

Jose I’m sorry I’m late to your comment. How are you liking your 10? Very nice rxer

@joseneves2822 2 жыл бұрын

@@JayN4GO yes indeed very nice, excellent audio ... meanwhile I bought the FC-40 tuner from Yaesu and stretched a wire about 23 meters, I have a good antenna 😉

@M0YKSHamRadio Жыл бұрын

Nice one Jay, I just set up my 101mp to your settings 👍 had a good report so far

@JayN4GO Жыл бұрын

You’re going to love the rig. Actually the Heil 781 sounds great on these rigs. I haven’t picked one up yet due to being in a Cw bubble.

@M0YKSHamRadio Жыл бұрын

@@JayN4GO I love ir already totally awsome . Got a great audio report from US last night thanks for the settings. Seem spot on with the YAESU M70 MIC

@frederich8472 Ай бұрын

Thanks Jay. I think that a BWTH at 1 is better for the high frequency. 73, Fred from Paris, France

@frankjohnson7204 Жыл бұрын

More Parametric equaliser confusion!! You need to be aware that what Yaesu calls "BWTH" is really Q (NOT Octave bandwidth). This is a serious error in all their documentation. The Q of a filter affects its bandwidth but Q and Bandwidth are NOT the same. Setting a higher value of Q will produce a NARROWER bandwidth effect, a lower value a WIDER bandwidth effect. If you set any "BWTH" (Should be labelled Q) to "0" (as you have done), that control will merely act as a gain control as that pole will have an infinitely wide bandwidth. Bandwidth (BW) to -3dB points is related to Q and frequency by the simple formula: BW = f/Q

@oldstarsgorizia 2 жыл бұрын

Thanks Jay for your video shared here.... very useful !! You're settings work fine for me. 73' Giorgio IV3EPO

@JayN4GO 2 жыл бұрын

Thanks Giorgio! I need to add another video for higher pitch audio when the band is horrible.

@oldstarsgorizia 2 жыл бұрын

@@JayN4GO Hi Jay, so...I'm waiting for it !! :) I've switched from an Ic7300 used at least 5 years with a great satisfaction but receiver of FTdx10 is one step beyond. I've compared also with an IC775 dsp and FT 5K and it's a great back-up radio maybe could be the main in some cases. Most of the time I use it on CW and it's a keeper !! 73' best regards. Giorgio

@JbirdlLester Жыл бұрын

Thanks Jay ..will try this out on my ftdx10.. I was getting bad reports on how I had it setup I'm using a Yaesu m70 desk mic hope the 80 meter guys like the setup you have was at the point of putting it back in the Box. fingers crossed thanks KB5VDO

@JayN4GO Жыл бұрын

Most guys on 80m run external rack gear. You can menu mod the 10 to 4K bandwidth and use a tube preamp into an apex 204 with big bottom. The 781 mic actually sounds good on this rig with some menu eq settings. If you can use a websdr to listen to yourself it really helps a lot.

@JbirdlLester Жыл бұрын

@@JayN4GO Hey Jay I Got the Yaesu M-70 because they was saying My Heil 781 g was not sounding good. I'm sure it was me on not knowing how to set it up properly thanks for the Info Greatly appreciate it

@kevinvanderveen2695 Жыл бұрын

Please settings for de yeasu m70 microphone for good modulatie on the yeasu ftdx 10

@shonniebhida 4 ай бұрын

Sir, at 2.25 time stamp on your Clip, I don't have a Deep voice, but I would love to sound Deep like BBC, am I correct in trying 100_2900 setting? Maybe not so good for Dx, but I would like to go Base'y I take it I need to go Down like towards 100--2900 not upwards.

@JayN4GO 4 ай бұрын

Yeah or 50-2900. You’ll get most of your bottom end from 50-150hz. You might like to buy an apex 204 with big bottom. There’s also the 0-4000 menu option for the dx10 😂

@W2JLDRoc-ham 2 жыл бұрын

i followed this vid before and did a recording on the radio and the audio out sounded good...........did a reset forgot to save the setings to the card. watched the vid again applied the same settings and now when i record the audio from the radio i got nothing.....i can only imagine i did something wrong...why could i just left it ALONE!!!! please help

@JayN4GO 2 жыл бұрын

Are you recording from the headset Jack in the front ? May need to check the monitor button and level

@cigale40 2 жыл бұрын

Thank you proc 5 for me

@JayN4GO 2 жыл бұрын

Nice I need to do a follow up video as I’ve changed some eq settings. Like you, I lowered my Proc and boosted other frequency’s. Hope you’re enjoying your dx10