I'm glad my video helped and well done. Thanks for watching and commenting 😊👍

Thanks for the feedback 👍🙂

Hi, where did you manage to find the m7x1 hex screws? And does that mean you only have to tap the existing 6 mm hole, so no helix-coil required? Thanks!

Yes I found the countersunk M7 x 1 screws on Ebay & used a Hinson CU216 rubber bush kit. The screws came from China, but were good quality. The length required is 20mm as countersink fasteners are measured from head face. The original rivet hole is 6mm, so is perfect tapping size for M7. Some people use M8 screws, but this I feel removes to much material from clutch basket upstands. Plenty of Loctite so they don't come out. Nice & quite now. Also chain tension is critical on these bikes & needs to be loser than the factory spec or make noise also. I run a Scottoiler as well. Cheers & good luck

@@carlsimons1688 thanks for sharing, this is such a common problem that all the info helps everyone 👍😊

​@@carlsimons1688 Thank you for the info! Much appreciated, will try to fix the bushings soon :) One more question, were you able to tap the old rivets out by a hammer after you have drilled the rivet heads out? Or should the be drilled out from both sides?

Thanks for watching, a mechanics job is to repair and not just through away 👍

​@@melsmotors where can I buy the silent blocks of the mt 09 clutch?

La mia fa un rumore a 3200 giri se punto la frizione sparisce non lo sopporto

@@danyk525 Yes, the rattle is irritating especially when at a stop light and you can really hear it.

@@brunofrancesconi1992 Hinson Racing Clutch Basket Cushion Kit (CU216)

Thanks for your feedback 🙂👍

My thoughts exactly

Gracias por mirar y por sus comentarios.

Someone else noticed that a week after the video went live and it was rectified, thanks for watching and noticing 👍☺

I did video it but it was hard to make out over the engine sound in the video.

I think when the enigine is running in neutral. Then you grap the clutch in then the clutch noise is gone. I have that also with my mt09. Great vid 👌

@@Stevo10MrI have the same on my tracer 900. When the bike is in neutral it’s louder than when I hold the clutch in. Have had the same on a F700GS. I thought that’s something normal

@@raresbirzu2436 thx for your answer

It happens to most of them including some of the R1's

@@melsmotors, a friend of mine with a similar one like mine, 2016 model, had the problem and installed a 2019 slipper clutch and problem is gone. Maybe he didn't ride the enough miles to get the problem back. I was thinking of doing the same but this repair you showed it's going to be way cheaper. Thanks again for your work, man. Best regards from Portugal.

Hi Jon, We have the rubbers made as we do so many and keep them in stock, I couldn't comment on other bushes, try them yourself and let others know. It's an expensive try if it doesn't fit! Thanks for watching.

I couldn't say, I've never seen one actually break anything! 😕

The vibrations was definitely a symptom and rattling clutch basket. Thanks for watching 👍😊

@@melsmotors thx you !!! best regards in France !

Yes we do this as a job, we get people from all over the country coming down for this repair or buying the rubbers from us and having a go themselves. 👍

@melsmotors I'm located in London is it any close to you? Just saw the website! Will probably contact back next week as attending the Hastings Day Run on monday and will he ok to do the job after that depending on proce and waithing times and that?

Hi, Just checking availability to drop off my 2015 Tracer 900 abs for the clutch fix and maybe new clutch plates as it all needs to come off I guess? With Thanks Ricardo

@@RicardoTheCraneOperator hi Ricardo, kindly ring the workshop to get availability please. Thanks

You always try and put them back in order, they can vary in size and thickness, plus the plates are mated together when bedded in!

I couldn't capture the noise on video very well, sorry!

@@NoNoSPE thanks, it's free music from KZfaq ☺️

Da, znam, ispravljeno je nakon odjela kada je netko drugi to spomenuo. Hvala na komentaru i hvala na gledanju

Hi, the fix is permanent, the bike has been going for almost 2 years now without an issue

Hola, tenemos las piezas de goma hechas, normalmente las vendemos en eBay pero no tenemos stock. Gracias por ver

Thanks for watching and commenting

I haven't had one come back yet!

The rivets are steel, they were probably hot riveted, personally I would stick with the bolts. If it works your way please let everyone know. Thanks for watching 🙂👍

we sell the rubbers, you have to buy the rest

There were no complaints about hard gear shifting! 🙂👍

I only drilled the head of the rivets then punched them through. The rivet holes are already the correct size for the helicoil tap, no further drilling is required. I hope this helps.

Perfect. Thanks for the information.

The engine was too loud when running so you couldn't really hear it, that's why it's not in the video, sorry

It can be from any mileage, from 3000 to 15000

@@melsmotors oh, was interested in the tracer 7. I'll not purchase it then

Do you mean the rubbers? If so we sell them. Please fill out the form on our website melsmotors.co.uk/contact-us/

yes exactly I would like to order them

Hi, this had 17,000 miles and we sell the rubbers

@@melsmotors How much does the kit cost including VAT and shipping to Italy? Thank you

@@predatorfzr Sadly I do not send outside of the UK, been scammed too many times!

Hinson Racing Clutch Basket Cushion Kit (CU216)

@@melsmotors How much is the rubbers ? I’m 🇬🇧 buyer Have you used M6 or M7 bolts Thanks

Hi, vibrations were one of the symptoms with this job. Thanks for watching 👍😊

Hi Ryan, the vibrations are part of the symptoms of this issue. But I can't confirm that you have the same issue from afar, I would suggest taking it to your local bike dealer for confirmation. Thanks for watching 🙂👍

Hi John, thanks for watching my video. Your bike has the exact same clutch basket, part number B7N1615000, so realistically, yes it could be the same issue, it's a very common problem. My customer also complained about a vibration which has now been eliminated since the fix. I've heard of this problem from as low as 15000 miles! It's unlikely to fail as I had to drill the rivets out, but it'll only get worse from here on. 🤞

@@melsmotors hi whats the size of the bolt and rivets?

Whats the complete spec tap drill size,thread insert size, bolt size & torque for the bolts?

@@betamaxtuned you need an M6 helicoil set ebay.us/twj90O everything you need is in the kit, Do not drill the holes bigger! they are already the correct size for the tap in the kit. Use lock tight ebay.us/nlu47f on the bolts and I think I torqued them to about 15Nm - 18Nm. Use a 1/4 torque wrench ebay.us/GNKxDy . The torque number is not overly important as long as they're all the same torque, you will get a feel for the correct tightness. I hope this helps and thanks for watching 👍😊

@@melsmotors whats the size of the taper screw and length?

It's a common issue and Yamaha will not put their hands up to it! Sorry dude 😔

My happened after 600 mile service too. Fowler's of Bristol not interested at all.

I'm in Bracknell, Berkshire

Where did your m8 get the rubber bushes from please as want to fix mine . Cheers . Gr8 vid

Some people would just rather not hear it! Thanks for commenting 👍👍😊😊

I believe they were

hinson cu 216

Hi oceanlancer, not that I'm aware, it's either repair or replacement. Thanks for watching 😊

Yes it is. Red loctite is bearing lock

Normally a chatter on idle, if you put the bike in 1st gear and release the clutch slowly whilst stationary just to load the clutch slightly the noise should stop, if it does then that's the problem.

@@melsmotors kzfaq.info7XHGZgVYkFg, heres a video of my noise, is it similar?

Yes they should but they're just ignoring the problem 😔

You can use any blue thread lock, there is no right or wrong, this is just a solution to this problem that I did. I used thread lock as a safety measure. Thanks for watching 🙂👍

@@melsmotors Thanks for answer.

Thanks for the update, yes the last plate is one notch over, I corrected the one in the video after someone else noticed it! 😣 Don't forget it's a 20 minute video.

No problem, we are currently struggling for stock as we have quite a few orders already in the queue.

@@melsmotors ok can i ask what was the total cost of the job please

Hi, the parts are only available through our trade supplier, not available for the after market, sorry

@@melsmotors is that parts from yz450?

@@przemekwarzycki6516 it could be I've never replaced one or seen one on a YZ450

Ok thx gretings from Poland

@@przemekwarzycki6516 i got the rubber parts lmk

So much easier 😁 Than a Guzzi

We have them made and sell them directly to consumers

@@melsmotors is possible to order this rubbers for 2014 mt09 and send it to Netherlands? Thank you

Hi, not a lot, it will just get louder. You'll only hear this on idle, during riding it's quieter and drives normally 👍

@@melsmotors Thank you!