You Have Been Installing Your Common Rail Injectors Wrong Since Day 1

You Have Been Installing Your Common Rail Injectors Wrong Since Day 1 | Installing Dodge Injectors

Рет қаралды 82,349

Күн бұрын

Dodge Common Rail Injector Install. Learn how to install common rail injectors and what you need to be aware of during the install.
Need some injectors? We have them for your common rail.
www.thoroughbreddiesel.com/pr...
► Check Out Our Other Install Videos Here: • Installation Videos
► Check Out Our Other Dodge Cummins Videos Here: • Dodge Cummins Videos
★ Saving Diesel Lives! Check out our online store for performance products at: www.thoroughbreddiesel.com/
☎ Give us a call for FREE ADVICE: (866) 737-4966
Please remember to SUBSCRIBE, LIKE, and COMMENT if you like our videos! It really does help us out! Thx for the support.
kzfaq.info...
❤ Join our Diesel Community ❤
● FACEBOOK: / thoroughbreddiesel
● TWITTER: / tbreddiesel
● INSTAGRAM: / tbreddiesel
● PINTEREST: / tbreddiesel
● BLOG: www.dieseladdict.com/
● SNAPCHAT: tbred_diesel
Chapters
0:00 Dodge Common Rail Injector Install
0:45 Purchasing New Injectors
1:40 Installing Injectors
3:50 Injector Bolts & Torquing
4:08 Retainers
4:58 Torquing
#cummins #dodgecummins #commonrail #thoroughbreddiesel #dieselpower #diesellife #dieselporn #truckporn

Пікірлер: 48

@johnkauffman1191 10 ай бұрын

I don’t know, but Dodge says different. It’s says 44 inch pounds a seat injector in. Then loosen Bolt bolts put feeder Or crossover tube and torque nut 11 inch pounds. Then torque injector final torque is 89 inch pounds. Go back to crossover tube and final torque is 37 to 45 Ft. lbs. Way it gets evenly torqued by a fourth step Torquing process. Thank you for the video I like your old video but that’s straight outta Dodge.

@drifterbbb3649 7 ай бұрын

It is 11 ft lbs (not in lbs), but yes, sequence from the manual makes more sense for getting the crossover tube aligned to the injector notch. 11-inch pounds is for the solenoid nuts (in 2006 manual).

@Mebob2001 11 жыл бұрын

Dont forget to blow out the hold down bolt holes! extreamly important

@Top_g80comp 7 жыл бұрын

amazing video thx man

@kirky6996 Жыл бұрын

Thank you for the video! It helps me finally understand how the high pressure fuel seals into the injector body via the feed tubes. Great explanation on torque sequence. Your videos are helpful for guys like me. Keep them coming!

@thoroughbreddiesel Жыл бұрын

You're very welcome!

@cumminscrazy30 11 жыл бұрын

Great video! It looks like you take a lot of pride in your work, which is nice to see :)

@paulisaacs5257 3 жыл бұрын

M oki 9k oh 3988l9k0 OP k I'll k.kk.

@whiteoak60 6 жыл бұрын

Awesome thankyou so much,, really helped! !!!!

@thoroughbreddiesel 6 жыл бұрын

Thank you for the kind words. This is why we make them.

@tosstossofficial9846 2 жыл бұрын

Please can you explain to me how to identify the negative and positive terminal on a common rail injector when the cable color are the same.Thanks

@tonybugeja3632 3 жыл бұрын

My 2006 tube hold down is 57 ft lbs not 34 ft lbs and 11 in lbs on the harness nuts not 13 in lb, great video just wanted to note the difference from my dodge service manual

@johnkauffman1191 10 ай бұрын

I think I would go with your service manual. I worked for Dodge for quite a few years. And the guy that taught me raise three kids through grade school and high school Catholic private schools working nothing but dodge Cummings.

@varmint223 3 жыл бұрын

Is there a way I can send you guys a video of my 06 Cummins to my it sounds funny but it mite be in my head it’s new to me so any little tap or sound I look into it deep

@raulleyva5313 2 жыл бұрын

You mentioned using petroleum jelly for injector seals and then said grease on tube rings, did you mean petroleum jelly on tube as well or grease? Thank you.

@wildoutdoors8336 Жыл бұрын

Petroleum jelly will work fine

@larrycarpenter-yt4ot Жыл бұрын

Is the 6.7 the same torque specs. as described in this video?

@thoroughbreddiesel Жыл бұрын

@andyvaldez7714 4 жыл бұрын

5.9 Cummins cranking but dont start. How do I know if it's the VP44 or the injectors, or anything else?

@thoroughbreddiesel 4 жыл бұрын

This video is for a common rail truck (Model year 2003 +). If you truck is a 98.5-02 truck and you have a no start, check lift pump pressure and codes to identify your problem.

@D_Snapp_Garage 3 жыл бұрын

I replaced all of my 06 injectors about 2015 when #6 went bad. I was a cheapskate and didn't replace connector tubes. My #5 injector just went bad so I ordered one, plus 6 connector tubes. Would you recommend replacing all 6 tubes? My truck has always started and ran well. I was, however, disappointed ever since I replaced all 6 injectors in 2015 (160,000 miles- truck now has 200,000)it has gotten a few less miles per gallon whether towing, empty, city, highway, etc.

@thoroughbreddiesel 3 жыл бұрын

Replacing the feed tubes wont hurt a thing, and one thing that may be good for the entire project is to have those tubes retorqued.

@D_Snapp_Garage 3 жыл бұрын

@@thoroughbreddiesel how would you recommend I replace the other 5 since those injectors don't need replaced? Remove old tubes, brush inside the hole clean, replace and torque the connector tube nut? Or loosen the injector bolts then insert and torque the new tubes? Or even more than that, pop injectors out and then push back in as if I am putting in all new ones, then install connector tubes?

@yoanrojas4191 Жыл бұрын

I need you help please I have a 5.9 Cummins injector problem

@thoroughbreddiesel Жыл бұрын

Give us a call 1-859-737-4966.

@hotbassist182 10 ай бұрын

what torque wrench are you using for the inch pounds? I can't find anything but torque wrenches in Ft/lbs

@55terriblegasser 10 ай бұрын

Mac tools snap on and harbor freight have them

@thoroughbreddiesel 9 ай бұрын

It’s a snap on ¼ inch drive, they read inch pounds. Most of todays newer digital torque wrenches will display inch pound too.

@jerryscroggins1549 6 жыл бұрын

Who needs to go college for it and pay for books,just switch to you tube 90 percent of learning is done with the eyeballs.

@thoroughbreddiesel 6 жыл бұрын

That's riigghhtt!!

@jodytalosig2052 6 жыл бұрын

sir..help me why my starex crdi no start without fluid starter what is ta common reason..and how to solve the prob..pls help me?

@tomboyle7289 Жыл бұрын

What type of grease, lithium, ball bearing, Vaseline, gear etc?????

@thoroughbreddiesel Жыл бұрын

I want to say anything will work here, but I'm sure someone will jump in and say “don’t use X grease blah blah”. We traditionally use assembly lube or just everyday bucket of high temp bearing grease.

@johncredico4079 6 жыл бұрын

Had dealership do this for me. They also charged me $700 for a new manifold cover. They said they are not reusable . I'm suspicious. What's the truth.

@andrewschlosser9483 2 жыл бұрын

they likely broke the cover. totatlly reusable.

@noeholguin5218 7 жыл бұрын

I apriciate the video" I just recently replaced all 6 of my injectors with remanufacured bosch injectors from a reputable e-bay dealer. I had 1 of them stay completely open causing an engine knock and clouds of white smoke. I was able to isolate #2 was the cause with the miller cap tools. I pulled it, put back in one of my old ones and now I'm at the point I have put back all my old ones and my truck will not stop smoking when I give her gas. there is no blow bye/blow back she idles perfect drives like she used to, but now I have white smoke and when I place a heavier load on her I get a cloud of grey smoke. any sugestions?

@thoroughbreddiesel 7 жыл бұрын

I think you are on the right track. Pull all injectors and send them back. I would also suggest running a compression test on the motor because the faulty injectors could have done some engine damage.

@mariomartin1981 3 жыл бұрын

@@krosario77 oil creating white smoke LOL

@mariomartin1981 3 жыл бұрын

@@krosario77 ummmmm,,,,most of the engines that burn oil had blue smoke,,now injectors leaking fuel i'v seen smoke white,,

@bikeconnectionbmx 2 жыл бұрын

I've changed my injectors now has that loopy idle, what did I do wrong??

@thoroughbreddiesel 2 жыл бұрын

Common rail dodge? Check feed tubes.

@bikeconnectionbmx 2 жыл бұрын

@@thoroughbreddiesel yes common rail. I've been checking seems like some tubes port to injectors are crushed and one injector looks like double o ring. This was done by a diesel mechanic guess he's NOT

@bikeconnectionbmx 2 жыл бұрын

@@thoroughbreddiesel I got it running real good. Now I think stuck injector knocking and smoking white. I have the cap to block off fuel to injectors but no rail fuel pressure but there's fuel coming out of the rail what is going on now?

@thoroughbreddiesel 2 жыл бұрын

You have the suspected injector line removed and capped off? If so and it doesn’t stop knocking you move to a different cylinder. I don’t think I understood exactly what you are saying.

@bikeconnectionbmx 2 жыл бұрын

@@thoroughbreddiesel I'm moving to a different Cyl. My question if an Injector is stunk would it cause no fuel pressure at the rail because that's what's going on