How to Install 24v Cummins Fuel Injectors | Power Driven Diesel
Рет қаралды 64,955
3 жыл бұрынBaron returns to KZfaq to show you how to install 24V Cummins injectors. If you have a 1998.5 thru 2002 Dodge Ram 2500 or 3500 equipped with a 24V Cummins engine, this video is for you!
Get your own upgraded "Fueling Package" here: powerdrivendiesel.com/product...
Or if you just want a set of injectors and you already have a tuner like a Quadzilla, Edge, or Smarty, get your injectors here: powerdrivendiesel.com/product...
Find the best 24v Cummins parts at the lowest prices here: powerdrivendiesel.com/product...
Power Driven Diesel is a specialty performance shop engaged in the engineering and development of high performance turbo diesel technologies.
1 435 962 9555
powerdrivendiesel.com
/ powerdrivendiesel
@CameronMatthews760 3 жыл бұрын
Recommendation on where to buy injectors from?
@pddofficial 3 жыл бұрын
A link for injectors is in the description, obviously we are biased but powerdrivendiesel.com/product-category/dodge-ram-diesel/1998-5-2002-2nd-gen-24v/24v-fuel-injectors/dodge-ram-cummins-1998-5-2002-2nd-gen-24v-fuel-injectors-budget-builder-24v/
@CameronMatthews760 3 жыл бұрын
@@pddofficial thoughts on reman for people on a budget?
@pddofficial 3 жыл бұрын
Bare nozzles are cheaper, we sell them and they work great!
@njdevi11 3 жыл бұрын
@@pddofficial recommendations for a pop tester setup for installing nozzles for the slightly advanced home gamer?
@andrewb9708 Жыл бұрын
@@njdevi11 There's quite a few options, they're typically $100-$400 for the testing unit. My local (and highly trusted) diesel shop charged me $50 to pop test and balance my injectors (brand new Bosch 245hp HO). Of course, all the installation work was done by me. It's not that bad of a job, it took me four hours to replace the injectors, cross over tubes, and do a valve lash adjustment.
@rubikrawler 3 жыл бұрын
I just installed my PDD 24v injectors on the Fummins and it’s running great. Looking forward to grabbing a quadzilla from you next.
@pddofficial 3 жыл бұрын
Sounds great!
@Rayraysrides 3 жыл бұрын
content is always great!
@niceguy4928 3 жыл бұрын
Thanks for the videos 👍🏻 wishing I had a Cummins.
@1matdad362 6 ай бұрын
APOLOGIES, NOTICED YOU FINALLY COVERED THE INTAKE, 👍
@KREperformance 3 жыл бұрын
Best way I found to get the copper washers out of the injector bore is use a flathead screw driver because it has a slight taper. It’ll get the washer hung on the taper when you give it a few love taps and she’ll come right out
@njdevi11 3 жыл бұрын
Fire arm cleaning kit. Those copper brushes work great. I think .308 works best.
@jimg2885 Жыл бұрын
Thank you for the video. Great info. Just subscribed and look forward to watching more of your videos.
@pddofficial Жыл бұрын
Glad we could help comments like this is why we do it!
@jimg2885 Жыл бұрын
@@pddofficial Just ordered my injectors after watching your video. Will be watching it again when I start the install. I like how you explained the process. Again Thanks
@pddofficial Жыл бұрын
@@jimg2885 thankyou so much for showing your appreciation. doing these videos is very time consuming but comments like yours make it all worth it. Baron
@ericbenttech2234 8 ай бұрын
Thanks for a very professional vid!
@pddofficial 8 ай бұрын
Glad you liked it!
@jrod5045 3 жыл бұрын
Woooo finally doing a series for VP44S!!!
@pddofficial 3 жыл бұрын
Of course!
@electricamir248 Жыл бұрын
Great video. Thank you.
@pddofficial Жыл бұрын
You are welcome!
@devinmanderson 2 жыл бұрын
Tech tip: crows foot or offset wrench really helps with getting injector lines and any other tight space lines off. Use them all the time to pull hydraulic lines off valve bodies.
@digitalmuzik8086 Жыл бұрын
Thx for tip. having this issue atm.
@devinmanderson Жыл бұрын
@Digital Muzik808 if all else fails harbor freight cheapo wrenches and a torch bend them mofos to fit...not you have a special custom tool welcome to mechanicing
@davidspeyers5740 3 жыл бұрын
This guy has done that a few times... his hands were flying!
@astoltzfus4 3 жыл бұрын
I saw another PDD video and thought, "Yes! Finally the UCC video!"
@lastkings6209 3 жыл бұрын
Can y’all do 6.7 Cummins next please?
@chadhester265 3 жыл бұрын
Keep em Cummins
@njdevi11 3 жыл бұрын
If you're doing injectors you might as well do pushrods and valve springs while you're in there... and studs. Lol.
@prashantverma6811 7 ай бұрын
Thanks
@pddofficial 7 ай бұрын
Welcome
@1matdad362 6 ай бұрын
CANNOT BELIEVE THAT YOU DIDN'T COVER THE OPEN INTAKE ! Otherwise good Vid!
@elemen7713 2 жыл бұрын
i just did my injrctor and now my truck is rought at idle is sound like is missfiring i know this truck dont have spark plug or glow plug but that the only way i can tell u how it sound like any help please
@Frankstgeorge88 2 жыл бұрын
How about one for a 5.9 common rail
@Mikheno 3 жыл бұрын
Just did this awhile back to install Bosch RV275 Injectors. Nothing more than common hand tools and a few hours of your time. I replaced the O-rings in the fuel tubes and adjusted the valves while I was in there. Make sure you get the copper washer out when pulling the old injector. You will probably need to leave a few injector lines loose when you start up for the first time. This will bleed the air out and save your battery from 20 minutes of cranking.
@pddofficial 3 жыл бұрын
Great to hear and good tip!
@hambuga69 11 ай бұрын
Seen this video quite a few times. I’m about to put some 7x0.010 vco injector nozzles on my 24v. Wonder how bad egts will be with stock hx35.
@pddofficial 11 ай бұрын
will need to watch the gauge for sure.
@anaconda7540 Жыл бұрын
In process of doing injectors on my 06 5.9. Everything went together great I never cleaned out injector bore bc they looked shiney. Now I’m seeing guys are spraying and scrubbing out with a brush. Do I need to pull them back out and clean out bores with a brush?
@pddofficial Жыл бұрын
No you should be just fine.
@jacobltrotter 3 жыл бұрын
Made me nervous on that hold down bolt I snapped mine off in the head and was using a torque wrench lol
@bluebird5100 3 жыл бұрын
What did you spray into the injector lines to clean them?
@pddofficial 3 жыл бұрын
brake clean and shop air
@blackout394 Жыл бұрын
Just installed the injectors from your PDD 24v 475hp fuel kit. Not sure what went wrong but got it to start up and it runs rough. Rough idle and rough acceleration until you get pretty high in the rpms. I bled the injectors good enough to my thought but could air still be trapped in the system? Should i try to re-bleed them again?
@pddofficial Жыл бұрын
Sounds like cross over tube not seated. Redo them and see if that fixes it. Please feel free to call our tech support team they would be glad to help you. 435-962-9555
@Mike-qu8bh Жыл бұрын
If you’re upgrading injectors, to a bigger injector, do you need to upgrade the connector tubes as well?
@pddofficial Жыл бұрын
No not unless you are running 7x.013 and bigger
@rrr3r2 3 жыл бұрын
We’ve all forgotten the connector tubes at one point
@jimg2885 Жыл бұрын
Question for you, do you not install new gasket at the air horn and valve cover? Did not look like it in the video. Thanks for your input.
@pddofficial Жыл бұрын
At the valve cover it is usually not necessary as the o ring rarely goes bad as for the intake horn depends how it comes out
@jimg2885 Жыл бұрын
@@pddofficial Thank you so much for the reply. You're awesome and again best video that shows the details. You are the most informative and I really appreciate a person that takes the time to do it right. Again ThankYou
@pddofficial Жыл бұрын
@@jimg2885 love to hear it!!
@ArturoGarzaID 2 жыл бұрын
4:38 what were you unscrewing 4:52 what were you pulling out, what did you drop?
@pddofficial 2 жыл бұрын
At 4:38 he is pulling out the hold down bolt for the injectors. At 4:52 still pulling bolts on the hold down but he set the impact down and the socket fell
@riverguy988 5 ай бұрын
Do I need to buy brand new cross over tubes to go with the new injectors? Can I just inspect my old ones?
@pddofficial 5 ай бұрын
If the tubes are not damaged yes you can reuse them.
@johnv.v.9716 3 жыл бұрын
Now you guys should do the proper way to do head studs. Do we need to pull the head and install a head gasket and adjust vales? By the way where is Todd, I miss Todd.
@drake_24v_hawkins 3 жыл бұрын
Do your headstuds one at a time, I do it in the torque sequence for the head, never bad an issue. Done it on several trucks.
@drake_24v_hawkins 3 жыл бұрын
100% adjust valves. Anytime you do anything with headgasket/torque the cylinder head, easy to do
@Joker-rx6xw 3 жыл бұрын
Where can I get me a set of those fancy coppers at?
@pddofficial 3 жыл бұрын
They come in our install kit
@doorymcfly3488 10 ай бұрын
Is it uncommon to just replace the o rings and clean the injectors out because they are leaking?
@pddofficial 10 ай бұрын
Yes they should be pop tested to insure proper working order.
@hounddog8862 Ай бұрын
Problem I’m having is high pressure on the fuel return to the fuel tank, there is vapor fumes and when filling the tank engine running it’s pushing fuel out . Any suggestions on why
@pddofficial Ай бұрын
Could be a restricted return or the tank vents clogged
@hounddog8862 Ай бұрын
@@pddofficial all seams free of restrictions or clogs, I believe there is a bad o ring on one or more injectors causing the pressure to push back towards the return
@evangriebe3861 7 ай бұрын
thanks for showing how you got the 6th injector line off 🤦🏻♂️
@pddofficial 7 ай бұрын
No problem 👍
@loopernite5747 6 ай бұрын
Get your hands dirty its not that hard figure it out 🤦🏽
@mmmontague9048 3 жыл бұрын
Lol this would have been good 3 days ago when i did mine oh well lol
@pddofficial 3 жыл бұрын
Dang guys forgot to upload this video, it's been ready for a few weeks now.... sorry about that!
@mmmontague9048 3 жыл бұрын
Haha all good its a great video gives me reassurance i did everything correctly
@dixiemae5042 3 жыл бұрын
Behind the curve today 😑
@pddofficial 3 жыл бұрын
Yep, you were asleep and got treed! LOL
@zslemp 3 жыл бұрын
hard to take yalls advice when everything yall build blows up
@pddofficial 3 жыл бұрын
We've never blown up a mild/moderate build, kinda like what most guys see day-in/day-out. The 2000+ HP stuff commonly has failures, parts breakage, etc.... BUT that big power carnage is hidden from Joe Public by most performance companies, we simply choose to share it so everyone can get an insider's viewpoint. If you don't like the free content, feel free to leave!
@zslemp 3 жыл бұрын
@@pddofficial just don't forget your throttle return spring and blame it on the pump builder. And don't show Joe public tods booger welds y'all do.
@DOAD_Diesel 3 жыл бұрын
@@zslemp it’s almost comical seeing people like you comment. Never built a 2000+ hp truck yet know everything about it and knows how to do it without failures. If you had half a clue why these engine fail under a high torque spike or why their last engine blew up the way it did your comment wouldn’t look so ignorant.
@stiffdrinkmime366 3 жыл бұрын
LMAO
@benitogordito5676 3 жыл бұрын
Slow. Down.
@wizardsleevesteve5256 3 жыл бұрын
kzfaq.info/get/bejne/nquTqLmDl9ysp4E.html
The Dog House
Рет қаралды 45 М.
Power Driven
Рет қаралды 76 М.
Trey haberman
Рет қаралды 11 М.
Power Driven
Рет қаралды 84 М.
thomas.letsgo
Рет қаралды 5 МЛН
Мотомалышка Алина
Рет қаралды 6 МЛН
EpicShortsRussia
Рет қаралды 780 М.
Chandan_edit _n.3
Рет қаралды 14 МЛН
Sash Dun
Рет қаралды 7 МЛН