Ich wollte mir so eine TDM kaufen. Habe schon gehört das einstellen der Ventile wäre so ein großer Aufwand a er als ich jetzt den Ausbau der Batterie gesehen habe werde ich mir dieses Motorrad nicht kaufen. Soetwas zu konstruieren ist doch eine Unverschämtheit gegenüber den Kunden. Unmöglich!
@yooufdeouf-li8zt5 күн бұрын
Great work ! Thankx
@hawkins73318 күн бұрын
Brilliant video, i have the same bike will now be doing my own tyre changes , thanks for sharing
@kevincollins946612 күн бұрын
Excellent video. Thanks for taking the time to make it. It is very helpful and confidence inspiring.
@kevincollins946613 күн бұрын
Excellent video. Thanks for taking the time and putting in the effort to make this video. It is very clear and concise. Nice slide hammer👍
@anselliott744017 күн бұрын
The red brake grease is for internal hydraulic components at assembly. "Rubber Grease" that is rubber and fluid inert. No reason to use it externally, it's not meant for that. A tiny smear of molybdenum if you are paranoid-but also not really necessary as the piston pushes-not slides- against the brake pad. You don't want anything that is lubricating near brake components. The rubber grease you use will just melt and run onto the disk then the pads.
@loteq10121 күн бұрын
Imagine building something so weak that it crumbles after 10 years or so because the plastic gets old. Cmon bmw! Not like headlights are important!
@simyk81021 күн бұрын
This has been helpful, thank you so much. One piece of advice though, when you use words to emphasize something, please keep them on screen for little bit longer.
@donniefraser560229 күн бұрын
😊😅
@elendshuraglump3620Ай бұрын
Very helpful. Thanks a lot 🙂
@AmendatuАй бұрын
Hy buddy! Do you know the part number please? Great video
@kalihi8041Ай бұрын
Cheers from California. Just wanted to thank you for your splendid videos. Helped me a lot with my 2001 R100RT.
@manuhonkanen2111Ай бұрын
Any idea how to install the gascap ring back on once removed? The plastics won't fit!
@golanmotoАй бұрын
very well-done job, excellent video, I have an R1200R 2007 and it's basically the same, BMW made some homework on those bikes so on the new models you do not have to disassemble the whole rear arm in order to extract the driveshaft and that is a beauty. I managed somehow to replace the boots and grease the splines without taking off the rear arm...but it was not easy to connect back the shaft to its place.
@stanykoninckx5921Ай бұрын
zorgvuldig gedaan 👍niet beter olie vol gieten? en olie 15w50 ? ik gebruik 5w40,ook goed?
@berentsenct4968Ай бұрын
Thxs great vid
@228ANDY2 ай бұрын
I simply wonder why BMW didn’t make the oil pouring hole on the top of the final gear case on the right side so that you don’t have to remove the wheel.
@LesRitaMitsouko2 ай бұрын
How often should the final drive oil be changed?
@FAP6172 ай бұрын
Might sound like a daft question but how long was the wood prop you used please
@impermanent-being2 ай бұрын
Very helpful, thanks a lot.
@tibork38452 ай бұрын
How do you keep your wheels looking like new? I wash the bike with car shampoo including scrubbing the wheels but they just look dirty. Thanks for this video, now I I know how to change the pads!
@StephenCruthis-fl5wz2 ай бұрын
what tool did you use to remove fill plug?
@dinosaursr2 ай бұрын
Excellent, no gimmicks, just the facts.
@SeniaiVolodia2 ай бұрын
Many thanks
@britfin0072 ай бұрын
Excellent video!
@DrAl_3 ай бұрын
Excellent work! Thanks so much!
@ronicard3 ай бұрын
Excellent video! Thanks for taking the time. Just used it to remove the front wheel on my 2005 GS so I could put a new tire on it.
@sunnfrancesunnfrance71363 ай бұрын
Bravo très bon tuto 👍… pas de frein filet sur les vis ?
@JackDinning-rc2yk3 ай бұрын
I can’t find these lights anywhere on eBay, need to do the same thing but all the casings seem to be different. Won’t find using references either.
@alxfeathers22873 ай бұрын
What a great series for any TDM owner, especially us newbies getting into it for the first time! Thank you for making this
@willpierson51384 ай бұрын
Just replaced my 1998 starter tonight…..thanks to this video it went like a breeze! Really appreciate your work! Ride safe!
@gracjanesz99874 ай бұрын
Super film
@Patrick-co1qm4 ай бұрын
Is there any thing that needs to be done to the rotor as far as turning it like a cars rotor?
@ArcanePath3604 ай бұрын
Nice video. Not sure if mine is on the way out on my R1200RT but every now and then I press the starter and it turns once, then dies. Sometimes if I hold the button down longer than 2 sec it drains the power until a factory reset happens. Usually only happens once after a short ride if I'm getting petrol or going shopping, so engine is still warm. And if I let go, let the battery recover for a few secs it then starts as normal. Battery shows 12v+ on the dash with engine off
@joost23014 ай бұрын
thanks! would an H4 LED also work proberly?
@sustainableliving8804 ай бұрын
No music…yeah!
@Overnity4 ай бұрын
lifesaver... mockingbird hill
@user-vk3kj4pe5k4 ай бұрын
Отлично!
@sundeephegde65625 ай бұрын
Why all those parts ,just remove fuel tank bolts and lift it,battery will be right under it.
@luigiorfe79465 ай бұрын
Ciao e scusa ma negli snodi della albero non si mette niente? Non andrebbe grasso? Forse 🤔 no perché schizerebbe?
@luigiorfe79465 ай бұрын
Ciao e complimenti un italiano ti segue 😊 scusa gli spessimitri son tutti uguali o devo comprare una buona marca e se sì quali è quali hai usato... Grazie e buona vita da Luigi
@marcpaesen4605 ай бұрын
How much mm is it from bottom dead center to top dead center??
@tnoisette14195 ай бұрын
Thanks for your videos. They are a fantastic 'how to' resource
@racerdaveracerdave5 ай бұрын
Straightforward and clearly done. Well done sir and thank you!
@PRO100Mechanic5 ай бұрын
👍 спасибо
@mikeyBee40455 ай бұрын
Is it best to lube the actual pistons too, if so what's best to use? Cheers
@peterfraiquin67585 ай бұрын
just place bike on center stand remove rear shock remove 2 bolts from battery box open battery box with 2 screws remove battery