Integrity modules usually come with a new O ring gasket which is important as it prevents leaks caused by plastic against plastic vibration loosening, which will give a leak code. USE A NEW O RING!

Why would you tilt your car on them little pads.. user error

I tried but had no success your fridge must have thinner stainless

I’m thinking of removing my ZR2 sports bar. Can I just unplug the first plug harness and weather protect it? Then leave the rest of the wiring harness to the fuse box. Will my cab brake light still work?

Crazy how different the specs are for torque, etc between this 8.25 and my Nitro 8.25

I’m on 250k on originals. No leaks but I’m sure I’m due to swap. Going to try bilstein 5100 due to towing to see if it helps. Great job with video.

Hows the ride quality

You should have shown the engine sound later....

Great information. Thank you!

Umm.. I hope no one tries going under there. Still looks sketchy to me.

I have a 2001 4.0 Grand Cherokee that will overheat when i drive it. It idles around 210 and won’t overheat but once i take it for a drive for around 20 minutes it will spike suddenly and have to turn the car off. It will spew out the radiator cap and the coolant reservoir will start bubbling. The head is brand new on it with no gasket leaks. I’ve replaced the thermostat, radiator, and heater core so far. Going to replace the water pump today but if it isn’t that what else would you think is wrong with the car? It runs perfectly fine other than the overheating issue.

To insert the flange at the end, couldn't you just have used the balljoint press reversed? Screw on the long side of the shaft and the open side against the flange to let the short shaft through? Very complete video, thanks! Also, if you are not going to use the fan clutch anymore, you don't need the whole pulley assembly. Just bypass it and use a shorter belt. You would need to disassemble it to get the clearance, but otherwise the pulley is not really needed. It's good to have it done in case you go back to clutch fan, though.

Thanks buddy! Replacing one tomorrow on a 2015 jeep, hoping the used ethos scanner I bought will work. If not I’ll buy this scanner through your page.

Hi, what is the specs of rims and tires using on integra looks awesome

Wow this is the real deal. I am taking my car tomorrow to my mechanic and show him this video

RIGHT ON THE MONEY!

What a measure without your rims

how loud is the alarm in person?

good lookin, after 6 minutes i've gotten into 7 silverados and one tahoe! chase dat paper!

Throttle body sensor crank but no start I change the sensor it crank but don't go all the way

This guy is high as hell

Im having starting issues with my jk, if my ignition switch is out will my anti theft kick on ???

Received the item and charged overnight. Put vac in pool. Moved approximately 3 feet then stopped. Contacted customer support and they were totally useless. Said since I purchased this on eBay, they would not honor the warranty. Do not waste your money, total garbage and horrible customer service

Your the only video that I have seen saying change the control arm bushings that holds the front rear end on thanks I got the same problem on a ram 2500 four wheel drive with a solid front axle it was getting so bad I was ashamed to drive it cause I looked like some fool with a violent shaking front end

Hope to do similar things to my 98 CRV RVI

excellent video, helped me do this job today

Fantastic!

Well I got mone out on today, and ket my vehicle get up to temp and the codes came back again plus now I have a new code showed up

Great video! Very informative and helpful! Made this installation a breeze! Thanks!

Cool video but why pressured to 13 psi when the radiator cap for that wrangler is 18 psi?

This could come in VERY handy on the newer Jeeps with the dual battery, auto stop/start setup. There’s a secondary aux battery that is notorious for failing and then draining your main battery, then you end up not being able to crank off of the main battery because the failed aux battery has killed it. If you connected this to that aux battery you could get some insight into when it might be failing. 🤔

😊😊

THANK YOU! THANK YOU! THANK YOU!! You just saved my sanity! I appreciate you😉

I know its not the fuses or a leak. The compressor moves manually but not when AC turns on. I thought maybe the AC clutch, the auto supply thinks its the blower motor resistor or the blend door actuator. Your video has vome across my stream, so this test is my next move. Crossing my fingers for the easy fix. Thank you for sharing.

great video good job!!!!!!!

CR -V ,1pok sovrimeh klasik 👍👍👍👍👍.xohda⚡. , no akkord 3 ca2 ca4 ca5

Absolutely incredible video, thank you so much ❤❤❤

Bro, thank you for the step-by-step on the video and the quality of it and not skipping all around. Appreciate the hard work and the time I took to create this 👍

You are awesome!!!!!!! One of the best and easy to follow repair videos ever ❤

I didn’t see him put lube on cam before installing???😮

Would it be better to replace the whole shaft?

LEGEND 🙌

Good video, i didn't realize the pressure switch was that easy to change. My 011 crv ac is acting up, blows cold for awhile and then just stops. I was going to top off the freon but the gauge was still in the lower green about 28 lbs. So i left that alone. Once the car sits for a while the ac will work again sometimes an hour before it blows warm. I dont hear the clutch engaging when its blowing warm. Radiator fans are good.

Bushing are bad because the caster is incorrect from the factory,instal 3.5 caster bushings and the rest will work correctly

“You have to know what you’re doing to know what I’m talking about” that was amazing❤️

Great video! Been searching for a video that goes over exactly how a low pressure switch works and yours is definitely the best one out there

Hello my PD says 18W and won't charge my battery?

Love the videos! Have myself a rd1 CRV. That I’m looking into doing the b16 head swap so these have helped massively 🤝

Chris Fix had same exact solution.

Is there any way to adjust the volume on the siren?