You need to reduce the vibration from the movement. this machine must be tightly bolted to a solid base.
@ulisescuellar44577 ай бұрын
Amazing , can you do live milling with c axis ?
@techguruakash37868 ай бұрын
Plz bro provide me information about pnp microcontroler. DIY controller or buy?
@haunguyenvan93138 ай бұрын
@ Cho mình xin sơ đồ bàn jack cn1b với 4 chân pul + - và dir + - thanhk
@svetozar16110 ай бұрын
Что за камеры для верха и низа использовались?
@m3rkwurdigliebe10 ай бұрын
снизу ELP-USBFHD01M-L28 + объектив Yumiki 3.9mm Lens 1/2.3 Inch IR 72D HFOV No Distortion сверху уже ссылка на али не работает. 1.3M какаято с припаянными в готовые дырки 3мм светодиодами
@danielzhao7916 Жыл бұрын
What vision system do you use?
@m3rkwurdigliebe Жыл бұрын
OpenCV...
@justinwhite9535 Жыл бұрын
Any idea if your config on git would work on a new version of Linuxcnc? I've been down a rabbithole of trying to use OpenPnP on top of LinuxCNC, at this point it seems like it would probably be a better bet to try to get your setup working on my machine. Looks like it was created when LinuxCNC used Python 2 which is why I'm not sure that it would just work these days.
@marios2liquid Жыл бұрын
Hey, i also got one recently, wanna share some manuals? I have many for the Jukis, and might also need some help with LinuxCNC!
@m3rkwurdigliebe Жыл бұрын
i haven't found any manuals either so far
@marios2liquid Жыл бұрын
@@m3rkwurdigliebe i have many i can share
@marios2liquid Жыл бұрын
how to contact you?
@nikbivation Жыл бұрын
wow nice!
@krzysztofcebula2502 Жыл бұрын
Super
@israfilcaglar9216 Жыл бұрын
Which io card are you using? are the drivers original traub? original cnc must have tx8i computer
@m3rkwurdigliebe Жыл бұрын
yes, TX8i is a mitsubishi meldas 500. using my own interface cards - two YMDS2P (yurtaev.com). yes the drives are original mitsubishi MDS-x-V/SP
@israfilcaglar9216 Жыл бұрын
@@m3rkwurdigliebe you are perfect👍 How many axes does your interface board support? Which servo motors does it work with? and how much is the price? we have a traub tnk 28
@m3rkwurdigliebe Жыл бұрын
@@israfilcaglar9216 the card has a single channel, so it supports 7 drives - the max the control protocol allows. had to use 2 cards with this traub. i can work with pretty much every mitsubisi motor/drive except mr-j2-*ct. please email me if you are interested...
@adrianmatracki8771 Жыл бұрын
Hi I saw your webbside and i have some questions about MR-J2S amplifilter May by you can help mi and give come advice with change firmware in this amplifilter ? Old broken amp was general purpose now i buy cheep amp version s046 but unfortunetly som parameters are blocked and i cant change it.
@wo0416 Жыл бұрын
Where i can get pulleys ?
@gregreynolds5686 Жыл бұрын
As a fellow LinuxCNC user - I know just how long that must have taken to get right 😃 Very nice work!
@ulisescuellar4457 Жыл бұрын
Amazing is this a custom machine? Similar tool change to a brother/robo drill
@blazini Жыл бұрын
I don't even have a lathe and I want those configs!
@m3rkwurdigliebe Жыл бұрын
it's far from finished yet, 2 turrets were just mapped to ZX/WU axes. very limited usability actually. when i have time and a bit of inspiration - i'll clean up and put all my linuxcnc configs on github
Wow friend you never fail to impress. Very impressive!
@svenkrause3433 Жыл бұрын
Respekt...das mit LCNC umzusetzen, dazu braucht es schon dicke Eier und jede Menge Zeit. Magst was zu der verbauten Hardware sagen und zu den beiden Hauptspindeln?!
@m3rkwurdigliebe Жыл бұрын
the 2nd carriage UW plane is pretty limited: no G2/G3 support, no spindle sync moves and maybe something more. and of course ideallay the controller need 2 separate channels... ask me if you want to know something specific
@keithemery4219 Жыл бұрын
What is the pitch of the ball screw? Nice job!!
@m3rkwurdigliebe Жыл бұрын
20mm
@keithemery4219 Жыл бұрын
@@m3rkwurdigliebe I have searched high and low and your Pick and Place is the best out there. Have you published a BOM in the past? I plan on building one just like yours in the near future. Thanks for the great work you have done!! What is the length of your ball screw? Keith
@Nothing-27 Жыл бұрын
Great
@halaszattila8430 Жыл бұрын
Wao great job. :) How you solve 4 axis lathe in linuxcnc? X1+Z1 and X2+Z2 or X+Z and U+V?
@m3rkwurdigliebe Жыл бұрын
X+Z, U+W (and V for the counterspindle). not really a solution, just to test the motors. will try to have a look at the linuxcnc if it's possible to implement a second channel. C1 C2 (spindles position) also need some thought
@Mikle_Fedorov Жыл бұрын
А получилось независимо у разных шпинделей работать? Обеими револьверками
@m3rkwurdigliebe Жыл бұрын
нет, пока даже не думал как. надо 2 канала, на Linuxcnc.org народ обсуждал эту тему, но решения пока нет, насколько я понимаю. попозже посмотрю как оно устроено
@prashkd7684 Жыл бұрын
How come your air compressors are running so silent ?
@prashkd7684 Жыл бұрын
By far this is the best PNP design i've seen on KZfaq. You just need a heavier base to stop the machine shaking so much.
@arielrodriguezreyes2518 Жыл бұрын
Hello, I'm trying get control of mds-a-svj-10, but i haven't information about pin assignment and the protocol of communication with driver, could you share some information about that please?
@The_Unobtainium2 жыл бұрын
This is CRAZY!:)
@johnlocke96092 жыл бұрын
Hello there! Do you sell the card? I have 2 1.5kw MR-J4200b, want to connect them to use them for CNC. I found your site, but didn't found any info about drivers for windows, wanted to use them with Centroid Acorn, let me know, thanks in advance!
@m3rkwurdigliebe2 жыл бұрын
no info because there's no drivers for windows exist... the card is only usable under linuxcnc control
@johnlocke96092 жыл бұрын
@@m3rkwurdigliebe my friend just send you an email, he also uses linuxCNC. Thank you!
@abr55522 жыл бұрын
У меня есть MDS-B-SVJ2 как его подключить к CNC ?
@abr55522 жыл бұрын
Я намереваюсь подключить поворотный стол на двигателях MDS-B-SVJ2 k linuxcnc . Как их подрубить а ?
@tarikkuru2 жыл бұрын
Hello sir. Is it possible to do this with Arduino? What is the program that takes smd and shows where to put it?
@hakankum61492 жыл бұрын
Hello, I'm Hakan Kum. I like your machine. I want to use this machine in a different sector. How can I contact you?
@fadywageeh23342 жыл бұрын
How much will it cost to buy the pick and place machine?
@srikrishnasonone84252 жыл бұрын
Prise
@BIDOTEC2 жыл бұрын
Can you share wiring diagram ! Please
@aminelabidi61132 жыл бұрын
I'm hypnotized..! this is so cool congratulations man ♥
@ozgekaptan14872 жыл бұрын
Hello, it is very nice, can you share the design and the materials used?
@farhadvishkaee57562 жыл бұрын
Impossible! The video is sped up!!!
@Kevin_Tokyo2 жыл бұрын
By watching this video, I decided to apply 100w class servo to my Grizzly G0704, 400w was planed. LOL.
@kentvandervelden2 жыл бұрын
This appears to work astonishingly well! Your servos are very nice. Without the necessary resolution or response time on current measurements, the servos I have would lead to a very course height map. You are testing many interesting concepts! Thank you
@m3rkwurdigliebe2 жыл бұрын
thanks. the next video shows the resolution better... :)
@dimabelitskiy2 жыл бұрын
Крутяк.
@Pro_Stanki2 жыл бұрын
Дим, а что за платка на жопе? Где почитать?
@m3rkwurdigliebe2 жыл бұрын
так энкодер ж... самодельный, магнитный. модель микросхемы датчика - описании
@Pro_Stanki2 жыл бұрын
@@m3rkwurdigliebe магнитный, нормально живёт на таких оборотах? Ахренеть... 👍👍👍
@m3rkwurdigliebe2 жыл бұрын
@@Pro_Stanki ага, сам удивился. в даташите обещали 10000
@Pro_Stanki2 жыл бұрын
@@m3rkwurdigliebe да я потому и удивился. Думал они на больших скоростях не живут.. 👍