FranklinWoodWorks

Пікірлер

@pepsilove6306 4 күн бұрын

did something similar to this for a old ranger I had. the center two floor/bed boards tho I put on hinges and didnt bolt them down but used a groove sorta like cabinets so they could sit flush. this way if I ever needed to get at the fuel pump I'd never have to drop the tank. after doing two fuel pumps on my other trucks, I will never ever drop a tank every again. so i wanted to be able to just flip open a small section of my bed and easily reach the fuel pump.

@andrewerickson6690 11 күн бұрын

Ya couda changed the oil 8n the truck or dust crush up some charcoal in the mix

@antonioperez1624 16 күн бұрын

Sweet!

@RubenWoodcraft 21 күн бұрын

I realise this is an older video, but it might help if you cut a slot in the clamping piece. that way you can slide it on from the side and you don't have to remove the wing nut anymore since the rings can pass over it.

@FranklinWoodWorks2016 20 күн бұрын

Great idea!

@chriscolameco6850 26 күн бұрын

How is this holding up?

@FranklinWoodWorks2016 25 күн бұрын

Well, to be honest, I had to rebuild it using pressure treated wood. But other than that, no complaints. I also added "fender" cutouts when I put bigger tires on it.

@woodyholland9865 29 күн бұрын

Nice to see a woodworker build a flat bed. So many folks have no woodworking skills.

@woodyholland9865 24 күн бұрын

Also I just watched again. The pink color would be less if you use off road diesel. It is clear. Use it in my tractor.

@edwinbrown3303 Ай бұрын

Very cool restoration

@badsamaritan8223 Ай бұрын

a piece of angle-aluminum would improve the rigidity a lot.

@jameslaiola4976 Ай бұрын

Sir. I love it!!!!!!!!!!!!!! Im sendin you love❤ that is sooo awesome. I very respectfully wish to do the same.

@erschiessen Ай бұрын

How is the bed holding up after 4 years?

@go_rizzo_grow Ай бұрын

I think I'm going to copy this design, fantastic job man.

@Death2Compromise Ай бұрын

Were the floor boards just screwed into the wood frame? Flat bedding my 02 ranger.

@FranklinWoodWorks2016 Ай бұрын

Yes, just screwed in. But I would suggest using washers with the screws.

@corycampbell7000 Ай бұрын

I will be atempting this this summer. Thank you for the tutorial!!

@funk4t934 2 ай бұрын

Outstanding! Great tunes too ... thanks for sharing!

@timtaylor8998 2 ай бұрын

Awesome job!!!

@timtaylor8998 2 ай бұрын

Awesome job!!!

@timtaylor8998 2 ай бұрын

Awesome job!!!

@ARTUR_RUTRA 2 ай бұрын

Problem with this that's it already coast like a commercial samples

@NGinuity 2 ай бұрын

Chiming in from camp thumb cut due to Japanese pull saw. That thing is unforgiving. Opened me right up.

@FranklinWoodWorks2016 2 ай бұрын

You got that right!

@richranchernot 2 ай бұрын

You should have squared the fence with the blade not table.

@Tool-Meister 2 ай бұрын

Tre-wax for me, appears to be more durable than Johnson’s. I think Tre-Wax dries with a harder finish. I’ve used it since 1962, trying many alternatives throughout the years.

@anthonyperkins5856 3 ай бұрын

VERY NICE

@FranklinWoodWorks2016 3 ай бұрын

My goal has always been to get folks to think, even if it means folks figure out a way to make my designs better. Success! And let me know how it works out.

@gerardboulanger3702 3 ай бұрын

💪🏆 🌈

@ccpeter68 3 ай бұрын

Why not use 1/2 inch on just the back piece. The back piece only runs against the runner. That way the side where you cut can still be the 1/4. That back piece is even the bigger of the 2.

@torreydavis1690 3 ай бұрын

Did your fuel nozzle cap area end up too low for fall into the tank? How did you support it under the bed?

@CChase-rb5fv 3 ай бұрын

I just bought a Chevy Colorado that I need to build a bed on your very informative

@gregjohnson1872 3 ай бұрын

I looked through your videos and did not see how you made your baffle. I'll keep looking, but if you see this and feel like pushing me in the right direction it would be appreciated.

@FranklinWoodWorks2016 3 ай бұрын

It's called a "thien baffle." I didn't do a video because others on KZfaq have already posted builds. The videos I used as a guide were "Thien Baffle Top Hat Dust Separator" by ghostses. It's a five part series (really long but super detailed). I think I used his plans exactly, the variation may have been accounting for the size of my dust bin. Don't make the same mistake as others - make sure your dust bin is rigid. A plastic Rubbermaid trash can will collapse under the suction. I used a 55 gal drum, but I think any metal trash can will work. Although the build was tedious, it was very fun and the results are awesome. Good luck.

@Montgomeryleather2 3 ай бұрын

Man this looks great

@user-dp8nz7qn8e 4 ай бұрын

Just use Evaporust to remove the rust. No rubbing. Then get it copper plated then Nickel electroplated. It will never rust again.

@user-cz9mj6is5g 4 ай бұрын

Where did you find those tail lights?

@gnomacide07 4 ай бұрын

Very helpful video. Thanks.

@MarcusRefusius 4 ай бұрын

Johnson’s Paste waxx is now >$140 a can.

@njmxjunkie3128 4 ай бұрын

Came out beautiful

@jacklewis5394 4 ай бұрын

Someone (me) got drunk and kicked a fat dent in the side of my truck ive always wanted a flatbed and figured id look it up see what other people did this looks great and is exactly what i want to do with mine

@schechnera 4 ай бұрын

What a great design! I'm going to tweak it a bit for my lathe, but definitely will be building one of these. Thanks!

@DN-zh1bv 4 ай бұрын

anyone in MD DC area want to build one on my F350?

@NOSNOOB11 4 ай бұрын

You have inspired me to build somthing like this for my C 600 :)

@24revealer 4 ай бұрын

A piece of cardboard works to keep rust off machines too. I think it stop the moisture in the air.

@johnmilner7603 4 ай бұрын

I would have left the sides off. Now your elbows will hit it.

@cjustus648 5 ай бұрын

GREAT JIG! I drilled 1/8" holes 1/2' deep, cut pins 1" long. Rubber bands roll off the pins and center on 1" thick rings!

@dthomas6184 5 ай бұрын

Real late to the party, what depth did you cut to?

@basher875 5 ай бұрын

Much better than that plastic option I saw on related video Wood workers love wood End of

@crossgrainwoodproductsltd9230 5 ай бұрын

Of course you have the skills to align the holes. Next time, just drill the first hole all the way through, and using a larger diameter drill bit go through just the front. Do not go through it. This allows the screw heads to be recessed. Great job.

@davidlangston6927 5 ай бұрын

Love this. I have needed to upgrade my dust collection, this sure helps. You are right we have to do with what we have in the space that we have to work in.

@theshepster901 5 ай бұрын

No problem sexy hows your day

@theshepster901 5 ай бұрын

Looks awesome brother

@SMOKEY-JAYS-DIESEL 6 ай бұрын

Awesome job 👏🙏

@emeraldfox7175 6 ай бұрын

Whats this weigh compared to original metal bed? Thanks

@JoseRodriguez-dw9dv 6 ай бұрын

Looks nice 🙂

Ең жақсы KZfaq

Пікірлер